LASERWORLD FX Series Professional Show Laser Instruction Manual

LASERWORLD FX Series Professional Show Laser

Product Information

• Product Name: FX Series
• Manual: FX Series
• Date: 10/2021
• Page Count: 26

Product Usage Instructions

Product and Package Contents
Please check if all listed parts are included and undamaged.

Included in delivery:

• Laser system with power cable
• Mount
• DMX cable
• Manual

Preliminary Warning Notices

1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels, power supplies, or power cords.
3. Never look directly into the light source of a laser projector. The danger of damage to the eyes or even blindness in extreme circumstances!
4. This device must not be permanently connected to the mains. Disconnect it from the mains or use the power button to switch it off if not in use.
5. Any warranty claims are void if the warranty label is removed or tampered with in any way.

Initial Operations, Safety Instructions

1. Make sure to use the correct voltage; see the information on the device and in this manual.
2. Make sure that the device is not connected to mains during installation.
3. The installation has to be done by technically experienced and qualified persons according to safety regulations of the respective country.
4. Always ensure that the maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.
5. In some countries, an additional inspection by technical control institutes could be necessary.
6. Connect an easily accessible circuit breaker to the projector and objects.
7. For safe setup e.g. on walls or ceilings, please use a safety cord. The safety cord should be able to withstand tenfold the weight of the device. Please follow the accident prevention regulations of professional associations and/or comparable regulations for accident prevention.
8. If the device has been exposed to great temperature changes, do not switch it on immediately. Condensation (or any moisture/water formed) may damage this device.
9. Never use a dimmer, RC, or other electronically switched sockets. Whenever possible, do not use the laser projector together with large appliances (especially fog machines) on the same mains!
10. The power supply should be easily accessible.
11. When installing the laser, mount it with a minimum distance of 15 cm from the walls.

Please refer to the complete user manual for detailed instructions and additional information.

Legal notice

Thank you for purchasing this Laserworld product. Due to continual product developments and technical improvements, Laserworld (Switzerland) AG reserves the right to make modifications to its products. This manual and its content have been made with due care but Laserworld (Switzerland) AG cannot, however, take any responsibility for any errors, omissions, or any resulting damages forthwith. The brands and product names mentioned in this manual are trade marks or registered trademarks of their respective owners.

Attention:
This device is a show laser device for commercial use. This device is not a laser pointer, is not suitable for printing purposes, and must not be used as a laser pointer.

Security Label

Please read manual before operation

1. Laser radiation!
2. Laser class 3R
3. Caution of radiation if cover is removed
4. Model type
5. Output power
6. Production year
7. Wavelength
8. Power supply & consumption

Overview

Front Panel

• A. Laser aperture warning label
• B. Laser aperture

Back Panel

1. LED display
2. Mode
3. Up
4. Down
5. Enter
6. DMX cable
7. Power cable

Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery:

• Laser system with power cable
• mount
• DMX cable
• manual

Preliminary warning notices

1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels, power supplies or power cords.
3. Never look directly into the light source of a laser projector. The danger of damage to the eyes or even blindness in extreme circumstances!
4. This device must not be permanently connected to the mains. Disconnect it from the mains or use the power button to switch if off if not in use.

Any warranty claims are void if the warranty label is removed or tampered with in any way.

Initial operations, safety instructions

1. Make sure to use the correct voltage; see the information on the device & in this manual.
2. Make sure that the device is not connected to mains during installation.
3. The installation has to be done by technical experienced and qualified persons according to the safety regulations of the respective country.
4. Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.
5. In some countries, an additional inspection by technical control institutes could be necessary.
6. Connect an easily accessible circuit breaker to the projector.
7. The power supply should be easily accessible.
8. When installing the laser mount it with a minimum distance of 15 cm from the walls and objects.
9. For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord should be able to withstand tenfold the weight of the device. Please follow the accident prevention regulations of professional associations and/or comparable regulations for accident prevention.
10. If the device has been exposed to great temperature changes, do not switch it on immediately. Condensation (or any moisture/water formed) may damage this device.
11. Never use a dimmer, RC or other electronically switched sockets. Whenever possible, do not use the laser projector together with large appliances (especially fog machines) on the same mains!
12. Ensure sufficient ventilation and do not place the device on any warm or heat-ra-diating surface. Especially the ventilation openings must not be covered!
13. Ensure that the device does not get overheated. Make sure that the device is not exposed to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little while and leads to a degra-dation of performance.
14. This unit is intended for indoor as well as outdoor use.

Working on the device

1. This product has no user-serviceable parts inside and should only be maintained and serviced by a qualified engineer.
2. Be sure that the mains plug is not connected to the power supply while installing the device.
3. Take off all reflecting things like rings, watches, etc. before starting to work with or at the projector.
4. Only use non-reflecting tools to work on the device.
5. Wear protective clothing (like goggles, gloves, etc.) according to laser power and wave length of the laser.

Service notes

• Moisture and heat can reduce the lifetime of the laser system dramatically and expires any warranty claim.
• Quick on/off switching of this device will reduce the durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this device an ensure sufficient protection during transportation. Look after your Laserworld product.
• To increase the durability of your laser, protect the device against overheating:
  • Always ensure sufficient ventilation.
  • Do not face spotlights (especially moving heads) to the device.
  • Check temperature after approx. 30 minutes with each new installation. If necessary install the projector at a place with different temperatures.
  • Switch off the device when it is not needed. Diodes are switched on and can wear out even if there is no visible laser output.
• Please ensure the fans and heatsinks are clear from dust and debris otherwise the risk of overheating may occur. If the unit or air inlets appear to be blocked, please contact a qualified service engineer to maintain and service the product.
• Always place the laser behind fog machines and hazers
• Avoid direct exposure of the laser to moisture
• Clean the exit window with glass cleaner from time to time
• Removal of the warranty label, as well as damages to the device caused by improper handling, neglect of the safety instructions, and service notes, will void the warranty.

General Operation

1. Power
   Connect the device power plug to the mains. Make sure that your device is provided with the correct voltage. Wrong voltage could lead to irreparable damages. Please find the correct voltage data in the synoptical table at the end of this manual. Make sure that the device is not directed to people or inflammable objects during installation. To start the device just switch it on.

2. Modes/Functions
   The different operation modes can be selected via the four buttons next to the „Settings “ display.

3. „Mode“ button allows navigation through the menu. Press once to jump to the next menu point.

4. „Up“ / „Down“ allows for changing values.

5. „Exit“ confirms a selection.

MENU DESCRIPTION

AUTO
Auto operation allows to random playback the internal sequences. They are played back according to the internal system settings.

• Select „AUTF“ for fast run by navigating with the „Up“ / „Down“ buttons and confirm with „Enter“.
• Select „AUTS“ for slow run by navigating with the „Up“ / „Down“ buttons and confirm with „Enter“.
• Select „AUTH“ for slow run for white color by navigating with the „Up“ / „Down“ buttons and confirm with „Enter“.

DMX 512
The DMX mode requires a DMX controller or a Master laser (see 2.4. Master- Slave operation) to be connected to the laser. To switch to DMX mode, select „A001“ by navigating with the „Up“ / „Down“ buttons. Use the „Up“ / „Down“ buttons to set the desired DMX address and confirm with „Enter“.

DMX Chart
The laser uses 7 DMX channels, so make sure that the next device uses an address that doesn’t overlap with this range.

100%
4| Blue Laser Dimmer| 0 – 255| Dimmer laser output power from 0% to 100%
5| Strobe| 0 – 4| No strobe
5 – 255| Strobe from fast to slow
6| Rotation Speed| 0 – 255| Speed from fast to slow, 255 is stop
7| Rotation Direction| 0 – 99| Clockwise rotation
100 – 199| No rotarion
200 – 255| Counterclockwise rotation

MASTER-SLAVE

• This laser is Master-Slave capable. This means that the Master laser system can hand on a control signal to one or more Slave lasers, so all do the same.
• Master-Slave only works with lasers of the same product series of the same product generation.

Link lasers with DMX cable
To use Master-Slave operation, link the Master with the Slave lasers with DMX cables. Make sure to use the „DMX out“ port on the Master and the „DMX in“ on the Slave lasers. If several Slave lasers are used, link the first one to the Master laser and daisy-chain the control signal from the first Slave laser to the second etc..

Establish link to Slave lasers
The Slave units must be set to SLAVE („SLAV“) mode.

Activate Master Laser
The Master laser needs to be set as control source. To do that simply select „A001“ by naviga-ting with the „Up“ / „Down“ buttons. Confirm with „Enter“.

Set Auto mode on Master laser
To use the Master-Slave operation: set the Master to Auto mode (2.2.).

Final statement

Laserworld products are tested and product packaging is inspected before leaving our warehouse.

Users must to follow the local safety regulations and warnings within this manual and adhere to any regulations within its place of use. Damages through inappropriate use will void any liability or warranty of our products. Due to continual product developments, please check for the latest update of this product manual at www.laserworld.com. If you do have any further questions, then please contact your dealer/place of purchase or use our contact section on our website.A
For service issues, please contact your dealer/place of purchase and ensure only genuine Laserworld spare parts are used in any service repairs.

Errors and Omissions excepted and products are subject to change.

Laserworld (Switzerland) AG

Kreuzlingerstrasse 5 8574 Lengwil Switzerland

Registered office:
8574 Lengwil / Switzerland

• Company number: CH-440.3.020.548-6 Commercial Registry Kanton Thurgau
• CEO: Martin Werner
• VAT no. (Switzerland): 683 180
• UID (Switzerland): CHE-113.954.889
• VAT no. (Germany): DE 258030001
• WEEE-Reg.-No. (Germany): DE 90759352
• www.laserworld.com.
• info@laserworld.com.

Representative according to EMVG:
Tarm laser technologies tilt GmbH & Co. KG Lindenallee 27 D-44625 Herne.

Technical Data

(L x W x H) / (B x T x H) / (H x L x P)

Weight| 2.4 kg

Power specifications (at laser module)

 | guar. – typ.| Red (638 nm)| Green (520 nm)| Blue (450nm)
---|---|---|---|---
FX-700 Hydro| 700 mW| 200 mW| 220 mW| 300 mW

Laserworld (Switzerland) AG

Kreuzlingerstrasse 5 8574 Lengwil Switzerland

Registered office:
8574 Lengwil / Switzerland

• Company number: CH-440.3.020.548-6 Commercial Registry Kanton Thurgau
• CEO: Martin Werner
• VAT no. (Switzerland): 683 180
• UID (Switzerland): CHE-113.954.889
• VAT no. (Germany): DE 258030001
• WEEE-Reg.-No. (Germany): DE 90759352
• www.laserworld.com.
• info@laserworld.com.

Representative according to EMVG:
Tarm laser technologies tilt GmbH & Co. KG Lindenallee 27 D-44625 Herne.

References

• Laser Systems and Laser Show by Laserworld - lasershow, showlaser, laser display, entertainment laser, dj laser, club laser, laser rental, showcontroller, laser software

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>