LASERWORLD DS-1000RGB MK3 Professional Laser with Built In Multi Control Mainboard Owner’s Manual

LASERWORLD DS-1000RGB MK3 Professional Laser with Built In Multi Control

Mainboard

Product Information: Diode Series MK3

The Diode Series MK3 is a laser system designed for use in enclosed spaces only. It comes with a power cable, key, interlock bridge plug, manual, and technical datasheet. The device must not be permanently connected to mains and should be protected against dripping or splashing water. It is important to use the correct voltage and ensure that the maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.

Preliminary Warning Notices

1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels, power supplies or power cords.
3. This device must not be permanently connected to the mains. Disconnect it from the mains or use the power button to switch if off if not in use.
4. Never look directly into the light source of a laser projector. The danger of damage to the eyes or even blindness in extreme circumstances!
5. Do not operate the device at high humidity or in the rain or in dusty environments.
6. Protect device against dripping or splashing water. Do not place any liquid-filled containers near to this device.
   Any warranty claims are void if the warranty label is removed or tampered with in any way.

Security Label

• Laser radiation! Avoid exposure to beam
• Laser class 4
• Caution of radiation if cover is removed
• Model type
• Output power
• Production year |
• Wavelength
• Power supply & consumption

Initial Operations and Safety Instructions

1. Make sure to use the correct voltage; see the information on the device & in this manual.
2. Make sure that the device is not connected to the mains during installation.
3. The installation has to be done by technical experience and qualified persons according to the safety regulations of the respective country.
4. Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.
5. In some countries, an additional inspection by technical control institutes could be necessary.
6. Connect an easily accessible interlock connector or circuit breaker to the projector.
7. The power supply should be easily accessible.
8. When installing the laser mount it with a minimum distance of 15 cm from walls and objects.
9. For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord should be able to withstand tenfold the weight of the device. Please follow the accident prevention regulations of professional associations and/or comparable regulations for accident prevention.
10. If the device has been exposed to great temperature changes, do not switch it on immediately. Condensation (or any moisture/water formed) may damage this device.
11. Never use a dimmer, RC or other electronically switched sockets. Whenever possible, do not use the laser projector together with large appliances (especially fog machines) on the same mains!
12. Ensure sufficient ventilation and do not place the device on any warm or heat-ra-diating surface. Especially the ventilation-on openings must not be covered!
13. Ensure that device does not get overheated. Make sure that the device is not exposed to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little while and leads to a degradation of performance.
14. This unit is intended for indoor use only.

Working on the device

1. This product has no user serviceable parts inside and should
   only be maintained and serviced by a qualified engineer.

2. Be sure that the mains plug is not connected to the power
   supply while installing the device.

3. Take off all reflecting things like rings, watches, etc.
   before starting to work with or at the projector.

4. Only use non-reflecting tools to work on the device.

5. Wear protective clothing (like goggles, gloves etc.) according to laser power and wavelength of the laser.

Service notes

• Moisture and heat can reduce lifetime of the laser system dramatically and expires any warranty claim.
• Quick on/off switching of this device will reduce the durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this device an ensure sufficient protection during transportation. Look after your Laserworld product.
• To increase the durability of your laser, protect device against overheating:
  • Always ensure sufficient ventilation.
  • Do not face spotlights (especially mo-ving heads) to the device.
  • Check temperature after approx. 30 minutes with each new installation. If necessary install the projector at a place with different temperatures.
  • Keep the device dry. Protect it from moisture, rain and damp.
  • Switch off device when it is not needed. Diodes are switched on and can wear out even if there is no visible la-ser output.
• Please ensure the fans and heatsinks are clear from dust and debris otherwise the risk of overheating may occur. If the unit or air inlets appear to be blocked, please contact a qualified service engineer to maintain and service the product.
• Removal of the warranty label as well as damages to the device caused by improper handling, neglect of the sa-fety instructions and service notes will void the warranty.

OVERVIEW

Front Panel

• A. Emission led
• B. Laser aperture
• C. Beam block

Back Panel

1. LAN: Computer connection
2. Key switch |
3. 3. Scan Safety
4. 4. ShowNET DIP switches
5. X/Y Inversion
6. On/Off switch
7. Interlock In
8. Interl
9. Fuse
10. DMX In
11. DMX Out
12. ILDA Out
13. ILDA In
14. Power In
15. Power Out
16. Loop for safety cord |

Back Panel

1. ILDA Out
2. ILDA In
3. LAN: Computer connection
4. FB4 Display
5. Fuse
6. On/Off switch
7. Key switch
8. DMX In
9. DMX Out
10. Interlock In
11. Power Out
12. Power In
13. Loop for safety cord

Back Panel

1. Color control
2. Scan Safety
3. X/Y Inversion
4. LAN: Computer connection
5. On/Off switch
6. Interlok Thru
7. Interlock In
8. ShowNET DIP switches
9. Fuse
10. Key switch
11. DMX In
12. DMX Out
13. ILDA Out
14. ILDA In
15. Power In
16. Power Out
17. Loop for safety cord

Back Panel

1. ILDA Out
2. ILDA In
3. LAN: Computer connection
4. FB4 Display
5. Fuse
6. On/Off switch
7. Key switch
8. DMX In
9. DMX Out
10. Interlock In
11. Power Out
12. Power In
13. Loop for a safety cord

Preliminary warning notices

1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels, power supplies or power cords.
3. This device must not be permanently connected to mains. Disconnect it from mains or use the power button to switch if off if not in use.
4. Never look directly into the light source of a laser projector. Danger of damage to the eyes or even blindness in extreme circumstances!
5. Do not operate the device at high humidity or in the rain or in dusty environments.
6. Protect device against dripping or splashing water. Do not place any liquid-filled containers near to this device.
   Any warranty claims are void if the warranty label is removed or tampered with in any way.

3. Initial operations, safety instructions

General Operation

To operate the Diode Series MK3, please follow the instructions provided in the manual. It is important to avoid exposure to the laser beam and to only use the device in enclosed spaces. Refer to the product manual for more detailed instructions on working with the device.

1. Power
   Connect the power cord to the device and to the mains. Make sure that your device is provided with the correct voltage. Wrong voltage could lead to irreparable damages. Please find the correct voltage data in the synoptical table at the end of this manual. Make sure that the device is not directed to people or inflammable objects during installation. To start the device, connect the interlocking bridge, insert the key and switch it on, and switch the device on. The “Emission – Laser on“ LED at the front side of the device begins to light up when the device is ready for use.

2. Key Switch
   There is a key switch at the back of the laser system. Please plug the key to the switch and turn it on. The laser device only runs when the key is inserted and switched on. Prevent misuse! Unplug the key when the laser is unattended to prevent misuse of the system.

3. Fuse
   There is a fuse at the back side of the device. If the fuse should blow, please exchange it with a new one. If the problems recurs, please contact your dealer or the Laserworld service department.

4. Safety Presets
   This device has an integrated Scan Safety (SFS). Is the Scan Safety active (on), single be-ams are prevented. If the Scan Safety is switched off, it is possible to create full power single beams – be careful!
   Operating the laser system with disabled SFS may not be allowed in some countries. Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.

5. X / Y Inversion (only standard version with ShowNET mainboard)
   Use the X, Y buttons to invert the beams resp. patterns on the x-axis and/or y-axis.

6. Colors (not available for DS-1000RGB MK3, nor lasers with FB4 mainboard)
   Use the „red“, „green“ and „blue“ knobs to control the intensity per output color channel.

7. Modes / Functions
   The different operation modes can be selected by using the DIP switches next to the ShowNET-Display (or FB4) at the back of the device. Any change of the operation mode for ShowNET devices requires a restart of the device (disconnect power and reconnect it again). Do not change any ShowNET-Display settings during operation, as random and dangerous laser output can occur.

8. Turn device off
   To turn off the device, use the power button („OFF“), turn the key to ‚OFF‘ and disconnect the power cable from the mains.

Operation Modes

The Diode Series MK3 has different operation modes, which are explained in detail in the product manual. Refer to the manual for information on how to switch between modes and how to use each mode effectively.

Final Statement

Laserworld products are tested and product packaging is inspected before leaving our warehouse.
Users must to follow the local safety regulations and warnings within this manual and adhere to any regulations within its place of use. Damages through inappropriate use will void any liability or warranty of our products.
Due to continual product developments, please check for the latest update of this product manual at www.laserworld.com. If you do have any further questions, then please contact your dealer/place of purchase or use our contact section on our website.
For service issues, please contact your dealer/place of purchase and ensure only genuine Laserworld spare parts are used in any service repairs.
Errors and Omissions excepted and products are subject to change.
Laserworld (Switzerland) AG www.laserworld.com info@laserworld.com

For more information on how to operate your laser, please visit https://www.laserworld.com/en/online-manual.

References

• Laser Systems and Laser Show by Laserworld - lasershow, showlaser, laser display, entertainment laser, dj laser, club laser, laser rental, showcontroller, laser software
• Bedienungsanleitung
• Laser User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>