RONGTA Intelligent Data Terminal User Guide
- June 4, 2024
- RONGTA
Table of Contents
Intelligent Data Terminal
Quick Start Guide
Please read
this manual carefully before using the product and keep it properly
Introduction to Device Appearance and Commonly Used Keys
Introduction to the Obverse Side
Power-on: Press the power key for a long time in the power-off state until the
device vibrates. Power-off: Press the power key for a long time in the power-
on state until the power-off prompt appears, and click OK to power off. Close
screen: When the device is in normal working condition, press the power key
lightly, and the screen will be dosed. Sleep: The sleep mode can be triggered
by manually pressing the power key or setting the system to sleep. Wake up:
When the device is in sleep state, press the power key lightly. and the screen
lights up and the system wakes up.
Note: If you don’t use the device for a long time, please power it off.
The pictures are for reference only, please subject to practicality
Introduction to the Lateral Side
Introduction to the Reverse Side
Method of Installing SIM Card / TF Card
Unscrew the screws on the back cover of the bottom card slot with a tool,
and correctly place SIM1, PSAM card and TF card on the card slot.
Battery Charging Instructions
Use Direct Charger to Charge
Plug the Type C USB data cable into one end of the power adapter, and directly
connect one end of the Type C USE data cable to the charging port of the
device for charging.
Battery Use Instructions
The battery of this device is a polymer battery and cannot be disassembled.
Only the charger specified by the original factory can be used. Never
disassemble or replace the adapter at will. The battery should be charged in
time after it is out of power. It should not be stored for a long time under
the condition of empty or full power, and it is best to store it at about 50%
of the power, if you don’t use the device for a long time, please power it off
and store it.
Note: When you get the device for the first time, the remaining battery
power may be only about 50%. You can charge it through the attached power
adapter or charger with a holder (which needs to be purchased separately), and
use it after the first power consumption, Device Online Operation Instructions
When your personal computer is installed with an Android system driver or
mobile phone assistant, you can connect the device to the personal computer
through the USB data cable attached to the device. (You can download the above
software from the official website or other websites) Once you have installed
the above software, use the USB data cable attached to the device and insert
it into the USB port of the device and computer respectively, press the top of
the screen and scroll downward, the USB setting interface will appear. By
clicking ‘see more options, enter into the USB debugging interface, as shown
in right figure: The pictures are for reference only, please subject to
practicality.
| 
---|---
Note: If there is any change in the content of the manual, no prior notice will be given.
**FCC WARNING
**
Any Changes expressly or modifications not approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and {2)This device must
accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class 6 digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur ina particular installation. used for a long time,
remove the battery and store it separately.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or approved antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>