TIRAMISUBEST W550XY58044 Nest Swing with Swing Set Stand Instruction Manual

TIRAMISUBEST W550XY58044 Nest Swing with Swing Set Stand

• Stand Assembled Height: 79
• Nest Swing Diameter: 43
• Maximum User Weight: 150KG (330LB)

Light strip set

1. Lay the nest swing (1) on the floor and open the tabs with the Velcro straps.
2. Slide swing tubes (2) into the pockets of nest swing (1) as shown below.
3. Place the two swing cords (3) with the suspensions made ofplastic in the correct sequence next to the nest swing (1). Pleasemake sure that the swing cords (3) are not twisted.
4. Slide the plastic suspension of the swing cords (3) from above through the opening of the tab with the Velcro straps. Then use side II (see marking) to attach the suspension to the thickertube.
5. Now connect the swing tubes (2) to each other, while pressing down the spring button on the thinner end of the tube. Theinter-locking is achieved through the latching and clicking of thespring button. Now, close the tab with the Velcro straps.
6. Now, the nest swing seat is assembled as the photo shows.
7. Slide the light strip in the light strip set (18) into the pockets of nest swing (1). Control the light strip with the remotecontroller in the light strip set (18).
8. Put the thicker end of bottom frame tube (4) to plastic protective sleeve (16) and please make sure they are tightlyconnected. Connect upper frame tube (6) to middle frame tube (5),and the connection is achieved with M8 Bolt (8), M8 Spring washer(10), and M8 washer (9). Tighten the Connection with L shaped wrench (B). Repeat the process on the connection between upper frame tube (6) and middle frame tube (5).
9. Connect cruciform tube (7) to the 4 pcs upper frame tubes (6),using M8 Bolt (8), M8 Spring washer (10), and M8 washer (9).Tighten the Connection with L shaped wrench (B).
10. Attach carabiner (14) and M10 ring bolt (13) to cruciform tube (7) with M10 washer (12), M10 spring washer (19), and M10 nut (11). Tighten them with M10 wrench (C).
11. Rotate the lock of carabiner (14) until it is open. Hang the nest Swing on the stand by putting the ring of swing cords (3) in the carabiner (14). Make sure you lock the carabiner (14).
12. Remove part a and b from rope (15). Attach the bolt of rope (15) to bottom frame tube (4). Then Tighten connection with part a,b, and wrench (A).
13. Put Ceiling (17) on the top of the stand.
14. Congratulations! All Steps are finished. Please check again whether all connections are tightened or not. If all tightened well, you can enjoy the fun now!

WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT

AGE LIMIT

• This product is designed to be used by maximum one child between the ages of over 3. Maximum user weight is 330 lb (150kg)
• Do not allow children under three (3) years old nearby during assembly due to choking hazard from small parts.
• On-site adult supervision is required at all times for children of all ages.
• Do not allow use by children with any physical condition that may affect his/her ability to use this equipment safely.

BEFORE YOU BEGIN

• Carefully read all instructions in this manual before assembling and using this product.
• This unit must be assembled by adults. Heavy duty working gloves must be worn to avoid injuries during assembly.
• Children must not use the equipment until it is properly assembled
• Adult supervision is required during the use of this equipment at all times.
• Unpack all parts. Take a complete inventory of all parts and hardware using the parts and hardware lists in the following pages.
• Never add extra length to chain or rope. The chains or ropes provided are the maximum length designed for the swinging element(s).

LOCATION OF PLAY SET

• The equipment must be placed more than six (6) feet ( 1.8 meters) from any structures or obstructions, including but not limited to buildings, fence, garage, trees, laundry lines, electrical wires. Children can be seriously injured running or swinging into obstacles.
• The play set must be installed on level ground. Uneven ground must be leveled prior to installation. Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose and unstable which may result in serious injuries.
• Remove any tripping hazards from the safe play area, such as roots, tree stumps, rocks, landscaping, sprinkler heads, railroad ties, plumbing and electrical connections.

INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION

• DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use.
• ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous to users.
• DO NOT attach items to the equipment that are not specifically designed for use with the equipment, including, but not limited to, jump ropes, clothesline, pet leashes, cables and chains as they may cause choke hazards.
• The steel and plastic parts used in your product are subject to normal wear. Gradual deterioration of the material will occur, the speed of which will depend on the level of exposure to UV rays, airborne pollution, outdoor weather conditions such as rain and wind and the amount of use. You must inspect the equipment prior to every use. This includes, but is not limited to inspecting the set for cracks, excess wear, missing parts, loose connections, and for overall integrity. When the set shows any signs of weakness, you must stop using the play set immediately, properly store the set or restrict access by users until the condition is resolved.
• Verify that the suspended climbing ropes, chain or cable are secured at both ends and tightened, sothat there is no loose ropes, chain or cable hanging that can result in choking hazard.

When conducting inspections, it is recommended that you use the Suggested General Maintenance Checklist and Routine Inspection and Maintenance Issues checklists provided by the US Consumer Product Safety Commission, a copy of which is contained in this user manual.

CARE & MAINTENANCE INSTRUCTIONS

• Inspect all nuts and bolts twice monthly during the usage season for tightness and tighten as required. It is particularly important that this procedure is followed at the beginning of each season.
• Oil all metallic moving parts monthly during the usage period.
• Sand rusted areas on metal tubing and repaint using a non lead-based paint meeting the requirements of Title 16 CFR Part 1303.
• Check swing seats, ropes, cables and chains monthly during usage season for deterioration. Replacements should be made in accordance with the manufacturer’s instructions.
• Check all coverings for bolts and sharp edges twice monthly during usage season to be certain that they are in place and replace when necessary. It is especially important to do this at the beginning of each new season.
• Do not use when the temperature drops below 32 degrees F (0 degrees C); remove and store the plastic swing seats and slides indoors.

The Consumer Product Safety Commission estimates there are about 200,000 playground related injuries involving children each year. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self evident that a fall onto a shock absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed on hard surfaces such as concrete or asphalt and while grass may appear to be acceptable it may quickly turn to hard packed earth in areas of high traffic. Shredded bark, mulch, wood chips, fine sand or fine gravel are considered to be acceptable shock absorbing surface when installed and maintained at a sufficient depth under and around playground equipment.
Table below lists the maximum height from which a child would not be expected to sustain a life-threatening head injury in a fall onto four different loose- fill surfacing materials if they are installed and maintained at depths of 6″
(15.25CM), 9″ (22.9CM), and 12″ (30.5CM).

However, it should be recognized that all injuries due to falls cannot be prevented no matter what surfacing material is used.
We recommend that a shock absorbing material should extend a minimum of 6ft in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock- absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when Properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability of the material in your area and its cost.

• Observing the following statements and warnings reduces the likelihood of serious or fatal injury.
• Warning the owner to instruct children not to walk close to, in front of, behind, or between moving items.
• Warning the owner to instruct children not to twist swing chains or ropes or loop them over the top support bar since this may reduce the strength of the chain or rope.
• Warning the owner to instruct children to avoid swinging empty seats.
• Warning the owner to instruct children not to use the equipment in a manner other than intended.
• Warning the owner to instruct children not to get off equipment while it is in motion.
• Warning the owner not to allow children to wear inappropriate items, such as but not limited to, loose fitting clothing, hood and neck drawstrings, scarves, cord-connected items, capes and ponchos. These items can cause death by strangulation.
• Warning the owner to instruct children not to climb when the equipment is wet.
• Warning the owner to instruct children to remove their bike or other sports helmet before playing on the playground equipment.
• Warning the owner to dress children with well fitting and full foot enclosing footwear. Examples of inappropriate footwear are clogs, flip flops, and sandals.

AT THE BEGINNING OF EACH PLAY SEASON:

• Tighten all hardware.
• Lubricate all metallic moving parts per manufacturer’s instructions.
• Check all protective coverings on bolls, pipes, edges, and comers. Replace if they are loose,cracked, or missing.
• Check all moving parts including swing seats, ropes, cables and chains for wear, rust or otherdeterioration. Replace as needed.
• Check metal parts for rust. If found, sand and repaint using a non-lead paint meeting the requirements of 16 CFR 1303.
• Reinstall any plastic parts, such as swing seats or any other ttems that were removed for the cold season.
• Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as needed.

TWICE A MONTH DURING PLAY SEASON:

1. Tighten all hardware.
2. Check all protective coverings on bolts, pipes, edges and comers. Replace if they are loose, cracked or missing.
3. Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as needed.

ONCE A MONTH DURING PLAY SEASON:

1. Lubricate all metallic moving parts per manufacturer’s instructions.
2. Check all moving parts including swing seats, ropes, cables and chains for wear, rust or other deterioration. Replace as needed.
3. Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as needed.

AT THE END OF EACH PLAY SEASON:

1. At the end of each play season or when the temperature drops below 32 degrees F (0 degrees C).
2. Remove plastic swing seats and other items as specified by the manufacturer and take indoors or do not use.
3. Rake and check depth of loose fill protective surfacing materials to prevent compaction and tomaintain appropriate depth. Replace as needed. As a general rule, maintenance should be performed at any time it is deemed necessary.

DISPOSAL INSTRUCTIONS

1. Please use care when disassembling the equipment, when tt is no longer in operational condition. Wear heavy duty working gloves to avoid injuries.
2. Fully disassemble the entire swing and slide sets before disposal. Do not leave partially disassembled parts in areas accessible by children.
3. Should you wish to recycle the steel tubing, please take the frame to your local recyding center.
4. All plastic parts can be recyded, take it to your local recycling center. Do not let children play with any disassembled parts meant for disposal, such as chains, slide, tubing, bolts, nuts, screws, etc.
5. Ovvners shall be responsible for mai1taini1g the legoility of the warning labels.

Part List

INSTALLATION

1. Lay the nest swing (1) on the floor and open the tabs with the Velcro straps.

2. Slide swing tubes (2) into the pockets of nest swing (1) as shown below.

3. Make sure that thicker tube end with hole follows a pipe end with a spring button.

4. Place the two swing cords (3) with the suspensions made of plastic in the correct sequence next to the nest swing (1).Please make sure that the swing cords (3) are not twisted.

5. Slide the plastic suspension of the swing cords (3) from above through the opening of the tab with the Velcro straps.Then use side “II” (see marking) to attach the suspension to the thicker tube

6. Now connect the swing tubes (2) to each other,while pressing down the spring button on the thinner end of the tube.The inter-locking is achieved through the latching and clicking of the spring button.Now,close the tab with the Velcro straps.
   Now,the nest swing seat is assembled as the photo shows.

7. Slide the light strip in the light strip set (18) into the pockets of nest swing (1) .Control the light strip with the remote controller in the light strip set (18)

8. Put the thicker end of bottom frame tube (4) to plastic protective sleeve (16) and please make sure they are tightenly connected.Connect upper frame tube (6) to middle frame tube (5),and the connection is achieved with M8 Bolt (8) ,M8 Spring washer (10),and M8 washer (9).Tighten the Connection with L shaped wrench (B).Repeat the process on the connection between upper frame tube (6) and middle frame tube (5).

9. Connect cruciform tube (7) to the 4 pcs upper frame tubes (6),using M8 Bolt (8), M8 Spring washer (10),and M8 washer (9).Tighten the Connection with L shaped wrench (B).

10. Attach carabiner (14) and M10 ring bolt (13) to cruciform tube (7) with M10 washer (12),M10 spring washer (19) and M10 nut (11). Tighten them with M10 wrench (C).

11. Rotate the lock of carabiner (14) until it is open.Hang the nest Swing on the stand by putting the ring of swing cords (3) in the carabiner (14).Make sure you lock the carabiner (14).

12. Remove part a and b from rope (15). Attach the bolt of rope (15) to bottom frame tube (4).Then Tighten connection with part a,b and wrench (A).

13. Put Ceiling (17) on the top of the stand.

14. Congratulations! All Steps are finished. please check again whether All connections are tightened or not.If all tightened well,You Can enjoy the fun now!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>