Aurora I003868 Desk Lamp with Wireless Charging Instruction Manual
- June 6, 2024
- Aurora
Table of Contents
I003868 Mirabella Genio AURORA Desk Lamp with Wireless Charging
Main Features and Technical Parameters
- Power input: 12V 1.2A
- Rated power for light: 5.5W
- Dimming Type: Capacitive touch control ON/OFF, Step‐less dimming
- Three LED light mode switches: Warm White, Cool White, Day Light
- Color temperature: 2700‐6500K
- Wireless Charging output: 5W (MAX)
IMPORTANT SAFETY INSTRUCTION WARNING ‐ DO NOT EXPOSE THE ADAPTOR TO
MOISTURE.
WARNING: USE THIS PRODUCT ONLY ON A FIRM, LEVEL SURFACE AND PREVENT ANY
OBJECTS OR MATERIALS FROM COVERING THE LIGHT SOURCE AND/OR VENTILATION HOLES
OF THE PRODUCT. PLEASE READ THE INSTRUCTIONS BEFORE OPERATING THIS PRODUCT.
Indoor use only. ‐ Do not look directly at the light. ‐ LED module lamp head may get hot after several hours of continuous use, AVOID placing your hands directly on LED light panel. ‐ Keep the lamp away from materials that may burn. ‐ If the power cord or adaptor is damaged, replace the power supply cord and adapter.
Operation Instructions
Use this product only on a firm, level surface and prevent any objects or
materials from covering the light source and/or ventilation holes of the
product
- Connect the AC adapter input into the connector in the rear of the lamp. Note: Use only with the supplied AC adapter to avoid damage or fire.
- Touch the On/Off button to turn the lamp On or Off.
- To adjust the brightness, press and hold the On/Off button until the desired level of brightness has been reached.
- Touch the mode button to switch between 3 light temperature modes: Warm White, Cool White, Daylight.
- Timer Function: Press and hold the button to set the 40-minute countdown, the light will flash twice to advise you that the countdown is set. The light will shut down after the 40 mins have elapsed.
- Wireless Charging Function: Place your phone in the center of the charging pad to commence charging.
Note your smartphone must be compatible with Qi wireless charging to be able
to charge correctly.
Please refer to your device instructions for enabled capability. The device
case or cover should be removed to ensure a stable connection.
APP Connection Preparation
It is important that your phone is connected to 2.4Ghz Wi‐Fi and not to the
5GHz network.
To verify your mobile device is set to a 2.4Ghz Wi‐Fi network, navigate to
the Settings menu and click on Wi‐Fi. In this menu, you will see all the
detectable networks in your area. Locate the SSID (the name of your network),
and ensure that the Wi‐Fi SSID does not end with a 5G/5GHz.
Check you have a strong WI‐FI signal (at least two bars) in the location where the light is to be located.
If you don’t have at least two bars signal on your phone, then you may need to reconsider relocating the light to a different location or obtain a Wi‐Fi extender to boost the WI‐FI signal strength.
Install the APP and register Account
For the best experience, download the “Mirabella Genio” APP to your smartphone
from the App Store or Google Play, the Genio APP icon will be displayed after
it has been installed successfully.
Pairing the Light using Mirabella Genio App
Bluetooth Pairing Assistant (BK method)
Our latest Genio smart Wi‐Fi lighting range has a Bluetooth pairing assistant
function, to make the pairing even easier than before, to take advantage of
this function, please turn ON the Bluetooth function on your phone.
- Connect the supplied adaptor to the light and power on the light
- Wait for the blue indicator light to start to blink rapidly (1 blink per second) –The light is now ready to be paired, if it fails to blink rapidly, press and hold the M key until it starts to blink,
- Open the Mirabella genio APP, tap on +, it will automatically detect the smart device in your local network, follow the below steps to pair the light into your APP, please make sure you are using the 2.4Ghz Wi‐Fi name and password, do not use the Wi‐Fi Name that ends with ‐5G
If this method doesn’t work for you, please Turn OFF your Bluetooth on your phone, then re‐try the EZ method or AP method listed on the following pages.
Fast Blinking EZ method,
- Connect the supplied adaptor to the light and power on the light
- Wait for the blue indicator light to start to blink rapidly (1 blink per second) – The light is now ready to pair, if it fails to blink rapidly, press and hold the M key until it starts to blink,
- Please ensure your mobile phone is connected to your 2.4Ghz Wi‐Fi network (Genio Smart light is not compatible on 5GHz Wi‐Fi network)
- Open the Mirabella Genio APP, then tap on the “+” symbol, then choose Smart Lighting, and select the genio desk light from the list
- Follow the APP’s instructions carefully to complete the network pairing process. Please make sure you are using the correct 2.4Ghz Wi‐Fi name and password.
if the fast‐blinking method (EZ method, mentioned above) doesn’t work, please try the slow blinking (AP method) listed below.
Slow Blinking AP method (recommended method if you are using Telstra NBN
while the blue indicator light is blinking rapidly, press and hold the M key
again until the blue indicator light is slowly blinking (1 blink every 2
seconds) open the APP this time on the reset the device first screen tap
on EZ mode in the top right-hand corner just below the battery image,
select AP Mode (refer to the 1st and 2nd image below)
Now Confirm indicator slowly blinking (refer to image 3), hit Next,
then Go to connect and connect to Wi‐Fi named SmartLife_XXXX
After connected to SmartLife_XXXX, return to Mirabella Genio, APP will commence the 2 minutes countdown process
| Please pay attention to the screen to determent the cause of the time‐out
error
If the light never stops blinking, please check your phone setting, if you are
using iPhone IOS 14, please make sure Local Network permission is turned
on
if the light does stop blinking but is unable to progress to “register on
the cloud” it indicates a communication error with your router to our
cloud service (need to check router setting)| please check and ensure
1. You enter the correct 2.4Ghz Wi‐Fi name and password
2. move the light closer to the router to get a better Wi‐Fi signal
3. Manually disable the 5Ghz Wi‐Fi signal on the router. You can turn it back
after the device is paired
FAQs
Q. How to connect the light to another Wi‐Fi network?
A. tap on …Go into the lights settings page, tap on “remove device” to
remove it, reset the light, and pair it again through the app.
Q. Followed the pairing process but received time-out error?
A. Check the following;
- 5GHz Wi‐Fi signal on the router setting has been disabled
- Please ensure you entered the correct 2.4Ghz Wi‐Fi SSID and password
- Please try using Ipad or iPhone, if you have no luck with android devices
- Please read the latest FAQs on our website https://www.mirabellagenio.com.au/faqs/
- Please move the light closer to the router to get better wifi coverage
- Please call Mirabella Technical support
If you have done all of the above, but still failed to connect, then your modem could be incompatible with a smart device.
All trademarks are used for reference purposes only. Made in China
MIRABELLA INTERNATIONAL PTY LTD
1 MIRABELLA DRIVE TULLAMRINE VICTORIA 3043 AUSTRALIA
TOLL-FREE: 1800 636 528 WWW.MIRABELLAGENIO.COM.AU
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>