LOREX 393ACSOL3E Solar Panel User Guide
- June 13, 2024
- Lorex
Table of Contents
LOREX 393ACSOL3E Solar Panel
Product Information
| Product Name | Lorex Solar Panel |
|---|---|
| Model Number | ACSOL3 |
| Dimensions | 185mm x 120mm x 6.5mm |
| Weight | 0.286 kg |
| Material | Plastic, White |
| Power Interface | Micro USB |
| Cable Length | 13 ft (4 Meters) |
| Waterproof Level | IP65 |
| Solar Conversion Rate | Electronic Solar Cell |
| Maximum Power Voltage | Current Operating Temperature |
Product Usage Instructions
- Set the Bracket to the desired mounting position.
- Mark holes through the Bracket.
- Using the included drill bit, drill holes where marked. Always be careful of existing wiring, pipes, or other hazards when drilling. If you are not comfortable doing it yourself, consult a licensed electrician or installer.
- Using a screwdriver, secure the Bracket with the provided screws. Optionally, if you are mounting the Solar Panel into drywall, use the provided drywall anchors.
- To adjust the Bracket, loosen the Bracket adjustment ring by turning it counterclockwise.
- Turn the Bracket’s Threaded Ring counterclockwise to lower the Ring.
- Twist the solar panel clockwise onto the Bracket.
- Adjust the angle of the solar panel to receive direct sunlight, then tighten the Adjustment Ring.
- Connect the Solar Panel cord to the desired adapter.
- Run the Solar Panel cord to the camera.
- Pull up the power port cover on the camera and then connect the Solar Panel cord to the camera.
- Connect the MicroUSB Adapter to the Solar Panel cord.
- Run the Solar Panel cord to the camera.
- Pull up the power port cover on the camera.
- Connect the adapter to the camera power port.
- Open the Lorex Home app and then check the device battery status to ensure the Solar Panel is receiving enough light to power on the device.
Quick Start Guide
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Copyright © 2023 Lorex Technology Inc.
As our products are subject to continuous improvement, Lorex reserves the
right to modify product design, specifications and prices, without notice and
without incurring any obligation. E&OE. All rights reserved.
What’s Included
- Solar Panel
- Bracket
- MicroUSB Adapter
- Mounting Anchors & Screws (x6)
- Drill Bit
Tools Needed
- Drill
- Screwdriver
Installation Tips
- Choose a location for the solar panel with plenty of direct sunlight exposure. Do not install in a covered or shaded area. Performance is dependent on temperature and light exposure.
- Make sure to fully charge the camera battery pack. Refer to the product documentation for charging instructions.
- (Optional) To install the camera without any gaps between the device and the wall, drill holes to run the Solar Panel power cord through the wall.
Always be careful of existing wiring, pipes, or other hazards when drilling. If you are not comfortable doing it yourself, consult a licensed electrician or installer.
Installation
- Set the Bracket to the desired mounting position.
- Mark holes through the Bracket.
- Using the included drill bit, drill holes were marked.
- Using a screwdriver, secure the Bracket with the provided screws.
- Optional: If you are mounting the Solar Panel into drywall, use the provided drywall anchors.
- To adjust the Bracket, loosen the Bracket adjustment ring by turning it counterclockwise.
- Turn the Bracket’s Threaded Ring counterclockwise, to lower the Ring.
- Twist the solar panel clockwise onto the Bracket.
- Adjust the angle of the solar panel to receive direct sunlight, then tighten the Adjustment Ring.
- Connect the Solar Panel cord to the desired adapter.
Connect Directly to a Camera
- Run the Solar Panel cord to the camera.
- Pull up the power port cover on the camera, and then connect the Solar Panel cord to the camera.
Check the compatibility chart at lorex.com for up-to-date information about product compatibility.
Connect the Adapter to a Camera
- Connect the MicroUSB Adapter to the Solar Panel cord.
- Run the Solar Panel cord to the camera.
- Pull up the power port cover on the camera.
- Connect the adapter to the camera power port.
Check the Battery Status
- Open the Lorex Home app, and then check the device battery status to ensure the Solar Panel is receiving enough light to power on the device.
Need Help?
For additional support material, scan the below QR code or visit:
Register Your Product
Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty
Product Specifications
- Electronic : Monocrystalline Silicon
- Solar Cell : 20%
- Solar Conversion Rate Maximum Power : 3.2W
- Voltage : 6V
- Current : 530mA
- Operating Temperature : -30 ºC ~ 70 ºC
Structure
- Dimension : 185mm x 120mm x 6.5mm
- Weight : 0.286 kg
- Material : Plastic, White
- Power Interface : Micro USB
- Cable Length : 13 ft (4 Meters)
- Waterproof Level : IP65
Bracket
- 360° Adjustable wall mount bracket: Winding cable bracket
Model Information
- ACSOL3 : Lorex Solar Panel 6-95529-05222-9
Dimensions
- Package: Blue Box with Retail Sleeve
- Package Weight: 1.8 lb / 0.84 kg
- Package Dimensions (W × D × H): 7.9 × 5.1 × 3.5” /201 × 129 × 88mm
- Package Cube: 0.08cbf / 0.02cbm
What’s Included
Lorex Corporation 10440 Little Patuxent Parkway, Ste, 300, Columbia, MD 21044, United States
© 2023 Lorex Corporation
As our product is subject to continuous improvement, Lorex Technology &
subsidiaries reserve the right to modify product design, specifications &
prices without notice and without incurring any obligation. E&OE.
(23-0018-LOR) 06082023-1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>