ATTICA ATTJL01B111-BX Terra Series Rear Bumper Instruction Manual
- June 13, 2024
- ATTICA
Table of Contents
ATTICA ATTJL01B111-BX Terra Series Rear Bumper
Product Information
The product is a Terra Series Rear Bumper (model number ATTJL01B111-BX) designed for 2018-2023 Jeep Wrangler JL vehicles. It is manufactured by ATTICA4X4 and is intended for outdoor use. The bumper comes with optional lights, which can be installed according to the customer’s preference. The package includes a hardware kit consisting of various washers (W35, W27, W36, W25), hex head bolts (B56, B37), and a spare parts hardware kit.
Product Usage Instructions
-
Before installation, carefully read and understand all instructions, warnings, cautions, and notes provided in the installation instruction guide.
-
Refer to your vehicle owner’s manual for proper disconnection of electrical systems and lifting procedures if necessary for installing the rear bumper.
-
This installation may require technical skills and knowledge of basic mechanical work. If you are unsure of your capabilities, it is recommended to seek assistance from a trained professional.
-
Contact ATTICA4X4 customer service at 626-369-2121 for any questions or concerns before proceeding with the installation.
-
ATTICA4X4 is not responsible for any bodily injury or harm caused by improper installation.
-
Proper installation of the rear bumper requires familiaritywith the factory recommended procedures for removing and installing original equipment components. It is advised to have the factory shop manual and any specialized tools for your vehicle on hand during the installation.
-
Always wear eye protection when operating power tools.
-
Inspect all contents of the package upon receipt to ensure there is no damage and all installation hardware is included.
- Name of purchase location
- Bar Code on side of box
- Date above Bar Code
- Date inside box coverIf any parts are missing from the kit, provide the following information to ATTICA4X4:
Contact tech@attica4x4.com or call 626-369-2121.
-
Begin the installation by unpacking all items and inspecting them for damage or missing parts. If any concerns arise, contact the company from which you purchased the bumper.
-
If you have chosen to install the optional lights, do so before proceeding with the bumper installation. The wiring setup for the lights is left to the customer’s discretion.
-
Place the threaded plate(s) inside the frame as shown on the right side.
-
For the side mounting points, use W35 and W36 washers along with B56 bolts, using a 21mm socket tool. For the bottom mounting points, use W25 and W27 washers along with B37 bolts, using an 18mm socket tool.
-
Once the installation is complete, your Attica Terra Series Rear Bumper will be fully installed and ready for outdoor use.
-
If you have any further questions, email tech@attica4x4.com or call 626-369-2121 for assistance.
CAUTION BEFORE INSTALLING
Before installation – Read and understand all instructions,warnings, cautions,
and notes contained in this installation instruction guide. Consult your
vehicle owner’s manual for proper disconnection of electrical and lifting of
vehicle if required for installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing this
install please take this product to a trained professional.
After reading this guide please contact us with any questions or concerns
before installing product.
Customer Service: 626-369-2121
ATTICA4X4 is not responsible for any bodily injury or harm to you or your
vehicle as a result of an improper install.
Proper installation of this kit requires knowledge of the factory-recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory-recommended procedures may affect the performance of these components and the safety of the vehicle.
- Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information:
- Name of purchase location
- Bar Code on side of box
- Date above Bar Code
- Date insde box cover
TOOLS REQUIRED
- 21mm socket
- 18mm socket
HARDWARE KIT
INSTALLATION
Begin by unpacking all items and inspecting them for damage or missing items.
Any concerns, please contact the company you purchased the bumper from.
After inspection, remove your factory bumper.
Optional lights are included, if you choose to use them, install them first.
Wiring setup is up to the customers.
Place the threaded plate(s) inside the frame as shown on the right.
For the side mounting points, use W35 and W36 washers, and B56 bolts with a
21mm socket tool.
For the bottom mounting points, use W25 and W27 washers, and B37 bolts with a
18mm socket tool.
Once finished your Attica Terra Series Rear Bumper will be completely installed and ready to take to the outdoors!
IF YOU HAVE ANY QUESTIONS, PLEASE EMAIL US AT
TECH@ATTICA4X4.COM OR CALL US AT
626-369-2121
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>