ATTICA4X4 Terra Series Side Steps Instruction Manual
- June 13, 2024
- ATTICA
Table of Contents
ATTICA4X4 Terra Series Side Steps
Product Information
The product is the Terra Series side steps ATTJT02C104-BX designed for the 19-23 Jeep Gladiator JT. These side steps are manufactured by ATTICA4X4 and are intended to provide easier access to the vehicle while also enhancing its appearance. The installation of these side steps requires some technical skills and knowledge of basic mechanical work. It is recommended to consult the vehicle owner’s manual for proper disconnection of electrical and lifting of the vehicle if required during installation.
ATTICA4X4 is not responsible for any bodily injury or harm caused by an improper installation. Proper installation of this kit requires knowledge of the factory recommended procedures for removing and installing original equipment components. It is advised to have the factory shop manual and any special tools needed for servicing the vehicle on hand during installation. Failure to follow the recommended procedures may affect the performance of the components and compromise vehicle safety.
Always wear eye protection when operating power tools. Prior to installation, inspect all contents of the package to ensure that the product is not damaged and all installation hardware is included. If any parts are missing from the kit, please provide the following information to the purchase location or contact ATTICA4X4:
- Name of purchase location
- Bar Code on side of box
- Date above Bar Code
- Date inside box cover
- Email: tech@attica4x4.com
- Customer Service: 626-369-2121
The product comes with a hardware kit containing the following items:
- 12 x W23 Washers
- 4 x N17 Hex Flange Nuts
- 12 x W22 Washers
- 8 x B35 Hex Head Bolts
- 1 x Spare Parts Hardware Kit
The company’s contact details are as follows:
- ATTICA4X4
- 13942 Valley Blvd, City of Industry, CA 91746
- Email: tech@attica4x4.com
- Customer Service: 626-369-2121
- Website: www.attica4x4.com
Product Usage Instructions
- Begin by unpacking all items and inspecting them for damage or missing items. If there are any concerns, contact the company from which you purchased the side steps.
- After inspection, remove your factory side steps.
- Position the threaded plate by feeding it through the hole as shown on the right side of the vehicle.
- The front mount should be fastened using B35 bolts, W22, and W23 washers. These components should be connected to the threaded plate using a 16mm socket tool.
- Repeat the previous step for the other mounting point.
- The middle mount requires W23 washers and N17 nuts. Use a 15mm socket tool to secure these components.
- The rear mount is similar to the front mount. Fasten it with B35 bolts, W22, and W23 washers. Connect these components to the threaded plate using a 16mm socket tool.
- Once finished, your Attica Terra Series Side Steps will be completely installed and ready to take on the outdoors!
If you have any questions or need further assistance, please email tech@attica4x4.com or call 626-369-2121.
CAUTION BEFORE INSTALLING
Before installation – Read and understand all instructions,warnings, cautions,
and notes contained in this installation instruction guide. Consult your
vehicle owner’s manual for proper disconnection of electrical and lifting of
vehicle if required for installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing this
install please take this product to a trained professional.
After reading this guide please contact us with any questions or concerns
before installing product.
Customer Service: 626-369-2121
ATTICA4X4 is not responsible for any bodily injury or harm to you or your
vehicle as a result of an improper install.
Proper installation of this kit requires knowledge of the factory-recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory-recommended procedures may affect the performance of these components and the safety of the vehicle.
Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information:
- Name of purchase location
- Bar Code on side of box
- Date above Bar Code
- Date insde box cover
TOOLS REQUIRED
- 15MM SOCKET
- 16MM SOCKET
HARDWARE KIT
INSTALLATION
Begin by unpacking all items and inspecting them for damage or missing items.
Any concerns, please contact the company you purchased the side steps from.
After inspection, remove your factory side steps.
Position the threaded plate by feeding it through the hole as shown on the right.
The front mount is fastened with B35 bolts, W22 and W23 washers. These components are connected to the threaded plate using a 16mm socket tool.
Repeat the previous step for the other mounting point.
The middle mount uses W23 washers and N17 nuts with a 15mm socket tool.
The rear mount is similar to the front, fastened with B35 bolts, W22 and W23 washers. These components are connected to the threaded plate using a 16mm socket tool.
Once finished your Attica Terra Series Side Steps will be completely installed and ready to take to the outdoors!
if you have any questions, please email us at
tech@attica4x4.com or call us at
626-369-2121
13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
TECH@ATTICA4X4.COM
626-369-2121
WWW.ATTICA4X4.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>