ATTICA ATTJL01B109-BX Apex Series Rear Bumper Instruction Manual
- June 13, 2024
- ATTICA
Table of Contents
ATTICA ATTJL01B109-BX Apex Series Rear Bumper
Product Information
- Product Name: ATTJL01B109-BX
- Manufacturer : ATTICA4X4
- Customer Service Contact : 626-369-2121
- Manufacturer’s Website : www.attica4x4.com
Product Usage Instructions
- Before installation, read and understand all instructions, warnings, cautions, and notes provided in the installation instruction guide.
- Consult your vehicle owner’s manual for proper disconnection of electrical systems and lifting procedures, if required for the installation of this product.
- This installation may require technical skills and knowledge of basic mechanical work. If you do not feel capable of performing the installation, please seek assistance from a trained professional.
- Contact customer service at 626-369-2121 for any questions or concerns before installing the product.
- ATTICA4X4 is not responsible for any bodily injury or harm to you or your vehicle resulting from an improper install.
- Proper installation of this kit requires knowledge of factory recommended procedures for the removal and installation of original equipment components.
- We recommend having the factory shop manual and any special tools needed to service your vehicle on hand during the installation.
- Always wear eye protection when operating power tools.
- Inspect all contents of the package to ensure that the product is not damaged and all installation hardware is included.
- If any parts are missing from the kit, provide the following information to the purchase location or contact tech@attica4x4.com or 626-369-2121
- Name of purchase location
- Bar Code on the side of the box
- The date above Bar Code
- The date inside the box cover
- Begin by unpacking all items and inspecting them for damage or missing items.
- If there are any concerns, contact the Afternan y from which you purchased the bumper.
- A ter inspection, remove your factory rear bumper.
- Transfer your parking sensors to the Attica Apex Series Rear Bumper using the B55 bolts, N29 nuts, and a 10mm Socket.
- Place the threaded plate as shown. Note that some models of the Wrangler JL may have a threaded insert in the same location; in that case, flip the threaded plate over and only fasten the outermost nut.
- Once the threaded plate(s) are in position, insert your rear bumper into place.
- Mount your rear bumper using B56 bolts, W36 lock washer, and W35 washer.
- Hand-tighten the bolts on both sides of the rear bumper to mirror the provided illustration.
- Use B37 bolts, W25 lock washer, and W27 washer to secure both under-sides of the bumper.
For any further assistance or information, please contact ATTICA4X4 at 626-369-2121 or visit their website at www.attica4x4.com.
CAUTION BEFORE INSTALLING
Before installation Read and understand all instructions, warnings,
cautions, and notes contained in this installation instruction guide. Consult
your vehicle owner’s manual for proper disconnection of electrical and li˜ting
of the vehicle if required for installation of this product. This installation
may require some technical skills and knowledge of basic mechanical work. If
you do not feel that you are capable of performing this install please take
this product to a trained professional. After reading this guide please
contact us with any questions or concerns before installing the product.
Customer Service : 626-369-2121
ATTICA4X4 is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper installation. Proper installation of this kit requires knowledge of the factory-recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory-recommended procedures may affect the performance of these components and the safety of the vehicle.
- Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure the product is not damaged and all installation hardware has been included. If parts are missing from the kit, please be prepared to provide the following information:
- Name of purchase location
- Bar Code on the side of the box
- The date above Bar Code
- Date iinsidebthe ox cover
**Tools required
**
- 10mm socket
- 18mm socket
- 21mm socket
- 4mm hex tool
Hardware kit
INSTALLATION
- Begin by unpacking all items and inspecting them for damage or missing items. Any concerns, please contact the company you purchased the bumper from.
- After inspection, remove your factory rear bumper.
- Transfer your parking sensors to the Attica Apex Series Rear Bumper using the B55 bolts | N29 nuts | 10mm Socket.
- Begin by placing your threaded plate as shown.
- Please Note : Some model’s of the Wrangler JL have a threaded insert located where your threaded plate should go. If so, do not panic, just flip your threaded plate over and only fasten the outermost nut as shown above.
- Please Note : Some model’s of the Wrangler JL have a threaded insert located where your threaded plate should go. If so, do not panic, just flip your threaded plate over and only fasten the outermost nut as shown above.
- Once your threaded plate(s) are in position, proceed with inserting your rear bumper into place.
- After mounting your rear bumper, use B56 bolts, a W36 lock washer, and a W35 washer.
- Once you are done hand-tightening the bolts on both sides of your rear bumper, it should mirror what is shown to the le˜t.
- Use B37 bolts, W25 lock washer, and W27 washer into both undersides of the bumper.
- Please note: Some models of the Wrangler JL have a threaded insert located where your threaded plate should go. If so you will need to proceed with using the B56 bolt, W36 lock washer & W35 washer in the same location where the threaded insert resides as shown on the right.
- Please note: Some models of the Wrangler JL have a threaded insert located where your threaded plate should go. If so you will need to proceed with using the B56 bolt, W36 lock washer & W35 washer in the same location where the threaded insert resides as shown on the right.
- After all your bolts are hand-tightened. Proceed with tightening the B37 bolts on both sides of the rear bumper with your 18mm Socket to help your li˜t bumper into position.
- Please note: Use your 21mm Socket for the bottom B56 bolt if needed.
- Please note: Use your 21mm Socket for the bottom B56 bolt if needed.
- Once your B37 bolts are tightened, continue tightening the B56 bolts on both sides of your rear bumper by using your 21mm Socket.
- Finally, your Attica Wrangler Apex Series Rear Bumper is fully installed and ready to hit all forms of terrains.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>