ATTICA ATTFB01C103-BX Frontier Series Side Steps Instruction Manual
- June 13, 2024
- ATTICA
Table of Contents
ATTICA ATTFB01C103-BX Frontier Series Side Steps
Product Information
The 21-23 Ford Bronco Frontier Series Side Steps ATTFB01C103-BX are a set of
side steps designed for installation on a Ford Bronco. These side steps are
manufactured by ATTICA4X4 and are intended to provide easier access to the
vehicle’s cabin.
Before installing the side steps, it is important to read and understand all
instructions, warnings, cautions, and notes contained in the installation
instruction guide. It is also recommended to consult the vehicle owner’s
manual for proper disconnection of electrical and lifting of the vehicle if
required for installation.
This installation may require some technical skills and knowledge of basic
mechanical work. If you do not feel capable of performing the installation, it
is advised to take the product to a trained professional.
ATTICA4X4 is not responsible for any bodily injury or harm to you or your
vehicle as a result of an improper install. Proper installation of this kit
requires knowledge of the factory recommended procedures for removal and
installation of original equipment components.
Always wear eye protection when operating power tools.
Inspect all contents of the package to ensure that the product is not damaged
and all installation hardware has been included. In case of missing parts,
please provide the following information to the purchase location
- Name of purchase location
- Bar Code on side of box
- Date above Bar Code
- Date inside box cover
Contact ATTICA4X4 customer service with any questions or concerns before installing the product: 626-369-2121 or tech@attica4x4.com.
Product Usage Instructions
- Begin by unpacking all items and inspecting them for damage or missing items. If any concerns arise, contact the company you purchased the side steps from.
- After inspection, remove your factory side steps.
- Start by installing the two hardware support brackets together using the provided B20 bolts, W16 and W19 washers, and N22 nuts. Leave the hardware loose to allow bracket movement. The hardware will be tightened in a later step.
- Attach the hardware support brackets to the side step using the provided B20 bolts, W16 and W19 washers, and N22 nuts. Leave the hardware loose to allow movement in the bracket.
- Mount the side steps to your vehicle using the provided B32 bolts, W22 and W23 washers. For the smaller mounting points, use the provided B20 bolts, W16 and W19 washers, and N22 nuts. Once in place, secure them by tightening with a 13mm wrench and a 13mm socket tool.
- The side step lights can be connected to your tail light harness. Install the Attica inline tail light harness adapter and connect the side step light harness to it. Note that the extra connectors are intended for use with Attica Terra Series Rear Bumper and Roof Rack lighting.
For further assistance or inquiries, contact ATTICA4X4 customer service: 626-369-2121 or tech@attica4x4.com.
ATTICA4X4 is located at 13942 Valley Blvd, City of Industry, CA 91746. Visit their website at www.attica4x4.com.
CAUTION BEFORE INSTALLING
- Before installation – Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide. Consult your vehicle owner’s manual for proper disconnection of electrical and li˜ting of vehicle if required for installation of this product.
- This install may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional.
- A˜ter reading this guide please contact us with any questions or concerns before installing product.
- Customer Service : 626-369-2121
- ATTICA4X4 is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.
Proper installation of this kit requires knowledge of the factory recommended
procedures for removal and installation of original equipment components. We
recommend that the factory shop manual and any special tools needed to service
your vehicle be on hand during the installation. Installation of this kit
without proper knowledge of the factory recommended procedures may a°ect the
performance of these components and the safety of the vehicle.
Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information
- Name of purchase location
- Bar Code on side of box
- Date above Bar Code
- Date insde box cover
INSTALLATION MANUAL
tools required
- 13mm Hex socket
- 13mm wrench
hardware kit
Begin by unpacking all items and inspecting them for damage or missing items.
Any concerns, please contact the company you purchased the side steps from.
A˜ter inspection, remove your factory side steps.
- Start by installing the two hardware support brackets together using B20 bolts, W16 and W19 washers, and N22 nuts.
- Once in place, leave the hardware loose allowing the bracket movement, they will be tightened at the later step.
- Attach the hardware support brackets to the side step using B20 bolts, W16 and W19 washers, and N22 nuts. Leave the hardware loose allowing movement in the bracket.
- The side steps mount to your vehicle using B32 bolts, W22 and W23 washers. For the smaller mounting points, use B20 bolts, W16 and W19 washers, and N22 nuts.
- Once in place, secure them by tightening with a 13mm wrench and a 13mm socket tool.
- The side step lights connect to your tail light harness. Install the Attica inline tail light harness adapter.
- Connect the side step light harness to the inline tail light harness adapter.
- *The extra connecters are used for our Attica Terra Series Rear Bumper and Roof Rack lighting.
- A˜ter completing the previous step, connect it to the other adapter(s). Once finished, feed the wire harness underneath so that it can be connected to the lights on the side step.
Refer to the image shown on the right to see how to connect your Attica Frontier Series Side Step with the adapter(s).
Secure the wiring harness using zipties.
Once finished, your Attica Frontier Series Side Steps will be completely
installed and ready to take to the outdoors!
if you have any questions, please
- email us at tech@attica4x4.com or
- call us at 626-369-2121
- tech@attica4x4.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>