infobit iSpeaker DAP6 Network PoE Speaker User Guide
- June 13, 2024
- infobit
Table of Contents
infobit iSpeaker DAP6 Network PoE Speaker
Product Information
The iSpeaker DAP6 is a network PoE speaker that provides power supply, audio transmission, and signal control using a low-cost Cat5 twisted pair cable. It can be powered by any 802.3AT standard Ethernet switch and utilizes SSA inverter technology for efficient amplification and superior sound quality, even for low-power designs. The speaker supports high-quality audio and control signals through the DanteTM network port and can be controlled remotely from a PC or Mac using control software. It also features DSP integration for gain control, silence control, 5-band equalizer control, and amplitude limiting control functions.
Technical Parameters
- Technical: Bass 6.5-inch x1, treble 1-inch imported magnesium film + horn drive
- Sensitivity: 92dB (1w@1m)
- Output Power: 15.4-30W (Determined by PoE output)
- Maximum Sound Pressure Power: 118dB
- Impedance: 8 Ohms
- Vertical Coverage: Bass 6.5-inch x1, Treble 1-inch imported magnesium film + horn drive
- Horizontal Coverage: 60W
- Frequency Response Range: 70 Hz-21kHz
- Interface: RJ45
- Transmission Protocol: Dante
- Power Supply Method: PoE power supply
- DSP Processing: Supported
- Installation: Bring your own hangers
- Net Weight: 4.1 Kg
- Speaker Size: 197mm X 300mm X 118mm
Product Usage Instructions
- Connect:
- Connect the RJ45 port of the speaker to the Ethernet port of the PoE switch using a twisted pair Cat5 cable.
- Before switching on the power supply, ensure that the device is properly connected.
- The input source should be connected to the Ethernet port of the PoE switch using a twisted pair Cat5 cable.
- Note: Ensure that the PoE switch is compatible with the 802.3at standard.
- Connect the RJ45 port of the speaker to the Ethernet port of the PoE switch using twisted pair Cat5 cable. Before switching on the power supply, connect the device properly.
- About the input source: Connect the input source to the Ethernet port of the PoE switch using a twisted pair Cat5 cable. The input should be Dante™.
- Note: PoE switches are compatible with the 802.3at standard.
- Software Control – Dante Controller:
- After connecting the speaker to the switch, open the Dante Controller software.
- Complete the routing and device setup of Dante audio in the software.
- The software will automatically search for all Dante devices. No additional setup is required.
- To pair devices, find and click the crossing point of the input terminal and output terminal. A green icon will indicate successful pairing.
- Customize the name of Dante devices for easy memory.
- Dante also has a feature to remember previously matched pathways, so re-pairing is not required when reconnecting disconnected devices.
- Software Control – Download:
- Visit the download page of the official website to download the control software.
- Open the software and select the desired speaker from the drop-down menu.
- If no speaker appears in the menu, click the Scan button to scan for connected devices.
- To connect a mobile speaker, select the device ID of the speaker.
Overview
The network PoE speaker provides power supply, audio transmission, and signal
control using only a low-cost Cat5 twisted pair cable. It can get power supply
from any 802.3AT-standard Ethernet switch and uses SSA inverter technology to
achieve efficient amplification with superior sound quality even for low-power
designs. High-quality audio and control signals can be delivered through the
Dante™ network port and routed through the Dante™ Controller. DSP integrates
gain control, silence control, 5-band equalizer control and amplitude limiting
control functions, all of which can be controlled remotely from PC or Mac by
control software.
Software control
Dante Controller
After the speaker is connected to the switch, open the Dante Controller
software, where the routing and device setup of Dante audio will be completed.
When users connect to Dante devices, there is no need to set up the software,
and the software can search for all Dante devices in the first time. The
diagram below:
All Dante devices appear on the software, so the next step is to start matching device channels one by one. When we click on the plus sign next to the device name, the Dante channel for the device is displayed.
Users can customize the name of Dante device according to their own needs for easy memory. At the same time, open the input terminal and output terminal of the device for pairing. You only need to find and click the crossing point of the input terminal and output terminal, and the green icon as shown below indicates that the channel is successfully paired.
Dante also has a very nice feature, which is the ability to remember previously matched pathways, and when all of your Dante devices are disconnected, when reconnect, you don’t have to re-pair them, all of the route connections remain as they were before they were disconnected.
Please visit the download page of our official website to download.
Open the software and select the speaker you want to control from the drop-
down menu at the top left. If there is no speaker to control in the menu,
click the “Scan” button to scan the connected devices.
After opening the software, click to select the device ID of the mobile
speaker to connect the mobile speaker.
Note: After scanning, the computer will detect all connected Dante™
devices, please select a matching type of device for control.
Scene Setting Area
Save Settings Load Settings Default Settings
Fader control area
Frequency division area
Attention
To ensure the reliable use of the equipment and the safety of personnel,
observe the following precautions when installing, using, and maintaining the
equipment:
- Avoid the danger of electric shock, do not open the case. There is no part in the machine that can be repaired by the user. Non-professionals are not allowed to disassemble the equipment without permission, so as to avoid increasing the damage of the equipment. When repairs are needed, please contact the designated professional maintenance personnel.
- The machine shall not be exposed to dripping or splashing water. Do not place liquid objects such as vases on the device.
- Do not spill any corrosive chemicals or liquids on or near the equipment.
www.infobitav.com
info@infobitav.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>