Gaabor GVCM-M14Y01 Vacuum Cleaner User Manual
- June 13, 2024
- Gaabor
Table of Contents
Gaabor GVCM-M14Y01 Vacuum Cleaner
Precautions
Your vacuum cleaner is an electric appliance, which must be used under normal
conditions. Do not allow the vacuum cleaner to operate alone when unattended.
It is forbidden to use a vacuum cleaner to clean the following objects, so as
to avoid damaging the vacuum cleaner or causing fire, personal injury, and
other accidents. A. Heating objects, such as carbon fiber and cigarette butts.
B. A large shard, such as glass. C. Hazardous substances (solvents,
corrosives), corrosives (acids, cleaning agents), water and other liquids. D.
Inflammable and explosive materials, such as gasoline or alcohol products.
The power must be cut off when cleaning, repairing, or not using the vacuum
cleaner.
- Do not pull the power cord when cutting off the power supply. Hold the plastic part of the plug with your hand and pull out the plug.
- Please check whether the operating voltage of the vacuum cleaner is consistent with the power supply voltage.
- Do not use sharp objects to pass through the power cord of the vacuum cleaner to avoid damage.
- Please do not immerse the vacuum cleaner in water, and avoid approaching heating appliances or exposure to the sun to avoid fire.
- Do not drag the power cord to move the vacuum cleaner.
- Do not let children play with or operate the vacuum cleaner to avoid accidents.
- Do not use the vacuum cleaner under the following circumstances
- A. When the vacuum cleaner falls and is obviously damaged or operates abnormally. B. When the power cord is damaged.
- Do not open the machine under the following conditions, and send it to the maintenance department designated by the company for maintenance.
- Do not operate for a long time when the suction inlet is blocked to avoid motor damage and heat deformation of the vacuum cleaner. The power cord of this product is connected to the motor in a Y shape, so if the power cord is damaged, it must be replaced with a special power cord in the maintenance department designated by our factory.
Technical parameters
Model| Rated voltage| Rated frequency| Rated power|
Rated capacity
---|---|---|---|---
GVCM-Ml4Y0l| 220-240V| 50/60Hz| 400W| 1.2L
Product parts description
l. Holder
2. Power switch
3. HEPA filter element
4. Dust cup assembly
5. Injection nozzle
6. Four-wheel floor brush
7. Long-flat suction
Operation method
Note: Please unplug the power plug when installing or removing the parts of
the vacuum cleaner! Vacuum cleaner installation
Method 1
- Take out the host head of the vacuum cleaner, and connect the larger end of the injection nozzle interface with the dust cup assembly (Fig. 1).
- Connect the smaller end of the injection nozzle interface with the four-wheel floor brush (Fig. 2).
Method 2
- Take out the host head of the vacuum cleaner, and connect the long oblate suction interface with the dust cup assembly (Fig. 3).
Operation guide
Note: The suction inlet must always be kept unblocked and free of any foreign matters to avoid accidents caused by the overheating of the motor.
-
Power switch
Press the power switch to start the vacuum cleaner as shown in Fig. 4); Press the switch again, and the switch will pop up and the vacuum cleaner will stop working. -
Use this product vertically
Release the power cord and plug it into the 220V AC power socket; Select the correct accessories (four-wheel floor brush or long-flat suction) and connect them with the dust cup assembly of the vacuum cleaner according to the correct installation method; Press down the power switch to open the vacuum cleaner for cleaning. Press the switch again after use, the switch will pop up, the vacuum cleaner will stop working, and keep it properly.
Preventive measures
Important I: please turn off the vacuum cleaner when the suction port of the dust cup is blocked, and take out the lumpy substance before use.
- Do not put the vacuum cleaner near the heat source, radiation source, or burning cigarette end.
- Do not plug in the power plug when your hands are wet.
- Please remove large or sharp objects before using the vacuum cleaner to avoid damaging the filter of the dust cup.
- Please distinguish the plug and power cord when unplugging the power plug.
- Do not use this product to clean burning cigarettes, matches, or other burning objects.
- Do not use the machine until the dust cup is properly installed.
Maintenance
Please empty the dust cup and clean the dust cup filter after each use to achieve the best use effect.
- Hold the body of the vacuum cleaner with the left hand and the dust cup assembly with the right hand, and rotate it anticlockwise to remove the dust cup (Fig. 5).
- Take the dust cup and directly pull out the filter (Fig. 6).
- Empty the dust cup and wash the fine ash on the filter directly with water.
- Please wash the filter in cold water when it is seriously blocked, and install it into the dust cup after drying for 24 hours.
- Carefully replace the filter in the dust cup. It is prohibited to use the vacuum cleaner when the filter is not installed! Please replace the dust cup carefully.
- Install the dust cup on the machine body.
Note: Do not use the washing machine to clean the dust cup filter! Do not use a hair dryer to dry the filter, and dry it naturally.
FAQ
Scheduled spare parts filters
Note: The dust cup can be cleaned. Please replace the filter every three
months (depending on the actual use) to ensure the best filtering effect of
the product.
Important: Please make sure that the filter is dry when installed on the
whole machine!
Packing list
| Name | Host | Extension rod | Floor brush | long-flat suction | Manual |
|---|---|---|---|---|---|
| Oty. | 1 | 2 | 1 | 1 | 1 |
Manufacturer: UNITED GAIN LIMITED
- Entrusting party: HANGZHOU GLOBAL JET E-COMMERCE CO ., LTD
- Address: 1-1407, 501 2nd Avenue, QianTang New Area, Hangzhou.P.R.China
- Telephone:0571-88269187
- Origin: Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>