Gaabor Dust Mite Controller Instruction Manual

Gaabor Dust Mite Controller Instruction Manual

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order fo avoid a hazard.
‘The appliance was intended to household and indoor use.

Safety Notice for Using

1. Please check whether the power supply voltage is consistent with the parameers marked on the botiomnameplate before use.

2. .Please do not use the machine outdoors or on wet surfaces. It is only for indoor use.

3. Please ensure that the collection bin is correctly installed on the machine before use, so as not fo cause damage to the machine or affect the working effect. Please dry the collection bin before installing.

4. .Please do not block the air inlet and outlet of the machine with objects. Do not operate the machine when the air inlet is blocked. Please keep the air inlet away from garbage, hair and other substances that may affect the air flow. 5 Please turn off the power before moving the machine fo ofher places. Please unplug the plug when not in use or before maintenance. Do not pullthe wire when pulling out the plug, but pinch the plug and pull it out.

5. .Please do not use or store the machine near the following objects: heating devices such as furnaces,
   flammable gases and flammable materials. 7.Please do not run multiple appliances on one power terminal block at the same fime.

6. Please use a dry towel fo clean the metal head of the plug when it is covered with dust or water. Please do ot connect the power supply or run the machine when the power plug is wet,

7. Please do not use the power cord to move or ift the machine, or close the door when the power cord is pressed under it, or place the power cord on sharp objects or in corners, or press the power cord fo run the. machine.

8. Do not use the machine to clean burning, smoking or sharp-edged obiects, such as smoke, knives and other objects, and do not absorb water and other liquids. 11.Do not touch the metal parts of the plug with your fingers while plugging in or unplugging, and do not touch the power plug and power switch with wet hands.

9. Please make sure you have unplugged the machine before each cleaning, and do not clean the machine: directly with non-nevtral cleaning agents such as water and alcohol

10. Please furn off the machine and stop using it immediately when the following conditions occur. (1) If there is abnormal noise, smell or smoke. (2) When the machine should work but fails to work.

11. UV-C ultraviolet light will harm human skin and eyes, please do not directly (long fime) irradiation of human, plants, animals, irradiation for too long to produce discomfort off, please seek medical atenfion quickly. Please conduct local tests on the object to be irradiated for sterilization and purification first fo avoid damage to photosensitive or non-UV resistant objects, do not panic if you are accidentally injured, facial burns can be healed after the epidermis falls off. When your eyes are injured, they will become red,
    swollen, watery and stinging and will take about three to four days to heal. We still recommended that you seek medical attention as soon s you are injured. Do not look directly at the lighted lamp with your eyes at any time to avoid injury.

Technical parameters

Product parts.

Electrical schematic diagram

Use instructions

1. Please connect the plug at the end and outside of the power cord to the civil voltage, then connect the power and press the switch button

2. Place the machine on the object o be cleaned (such as the bed), make sure that the two sefs of movable wheels at the bottom of the machine are pressed in, at this fime you can see a green light at the indicator light on the top cover, indicating that the UV lamp and slap has started to work, and slowly push the machine back and forth to clean. 3 Please put the machine and power cord in order affer use

Power on: plug inthe power supply, and turn 2Please gently push the machine while on the power swich. dleaning the bed, keeping the machine parallel * When the switch is pressed, it means “on”, to the edge of the bed and laying it fat on the ¢ when the switch is raised, it means “off”. bed

3. .Please place the machine flat on the surface 4.Please clean pillows, cushions and similar when cleaning carpet mats and move the items by moving the machine from back fo front machine up and down and back and forth as as shown in the diagram. shown in the diagram.

4. items by moving the machine from back fo front as shown in the diagram.

NOTE

Please clean the collection bin after each use of the machine.

Cleaning and maintenance

Mainfenance: 1.Although the penetrating power of ultraviolet light is sirong, but the dust on the lamp, stains will directly affect its penetrating ability. Quartz lamp shall be regularly wiped clean, so as ot to affect the UV penefration rate and irradiation intensity. 2.Please do not touch the quartz glass of the lamp with your fingers to avoid stains affecting the germicidal lamp. 3 Regularly clean the high efficiency filter HAPE, or replace the HAPE with a new one. 4.Please send the lamp fo repair when itis broken and do not disassemble it by yourself.

Cleaning:

Ploase fistfurn of the machine, unplug the power supply, press the dust box cover upward on both sides
with your hands to lift the dust collection bin assembly, and remove the filter parts to clean the waste. The
filter element and the filter cover can be rinsed with water, dried and put back into the dust box. 1.Al roufine maintenance and repair work must be done affer the vacuum cleaner is unplugged from the power source.
2.Please clean the waste in the dust bin frequently to avoid vacuum cleaner failure.
3.The surface of the vacuum cleaner should not be scrubbed with gasoline or oil-like substances, but with soft loth or neutral detergent, and the cloth must be wrung out when scrubbing, so that no water can seep into the electrical components of the vacuum cleaner. 4.Unplug the power cord, separae the power cord from the machine and store it properly. 5Keep the storage place dry. 6.D0 not stack heavy objects on top of the machine.

FAQ

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>