X-JOY W94G-403-9090-BТ Shower Enclosure Square Slide User Guide
- June 13, 2024
- X-JOY
Table of Contents
W94G-403-9090-BТ Shower Enclosure Square Slide
User Guide
- W94G-403-9090-BТ
- W94G-403-9090-МТ
- W94G-403-10080-BТ
- W94G-403-10080-MТ
- W94G-403-12080-BТ
- W94G-403-12080-MТ
- W94G-403-12090-BТ
- W94G-403-12090-MТ
Installation instruction
Attention!
- installation of item should be carried out only by qualified professional, following the instructions of this guidance;
- assembly is carried out by two persons;
- please, check for presence of all details after unpacking. Glass panels must be transported vertically;
- please, lean glass panels vertically against the wall during assembly of other parts;
- it is expressly prohibited to wap upon corners of glass panels
Recommendations for use
Attention!
It is required to remove protective film after carrying out of assembly
operations.
Product maintenance
Attention!
- for correct operation of the system it is required to install purification filters at feed pipelines with degree of purification of 100-300 micron.
- for the avoidance of damage of the surface of the product it is not allowed to use water of temperature more than 60 degrees C.
- use only mild detergents and soap for cleaning of the item.
- do not use corrosive washing agents or abrasive pastes for cleaning of the item.
- acute contaminations on the surface is recommended to treat with diluted vinegar and wash off with the water.
- shallow scratches (for acrylic parts of the item) can be removed with fine grid sandpaper (grade 2000) Instruction is designed for expert.
Assembly and installation must be carried out only by qualified professional
following the instructions of this guideline.
Attention!
Assembly is carried out by two persons. Manufacturer has a right to introduce
change of component parts that has no effect on appearance and functionality
of product.
All parameters indicated in this instruction have formal meaning. Manufacturer
reserves the right for technical changes.
Attention!
After assembly sealant must be given some time to harden. It is forbidden to
use item within 24 hours after completion of installation.
Disposal
The product to be disposed of in the usual way.
W94G-403-12080-BТ
W94G-403-12080-MТ
W94G-403-12090-BТ
W94G-403-12090-MТ 
Enclosure con
figuration
| 1 | mounting kit | х8 |
|---|---|---|
| 2 | vertical profile left | х1 |
| 3 | sealing rubber band | х2 |
| 4 | fixed glass 1/2 | х2 |
| 5 | F-shaped seal big | х2 |
| 6 | F-shaped seal small | х2 |
| 7 | door 1/2 | х2 |
| 8 | set of handles | х2 |
| 9 | magnet sealant kit | х1 |
| 10 | glass guide kit (right – left) with screw | х1 |
| 11 | S-shaped seal | х2 |
| 12 | bottom sill | х2 |
| 13 | Sill connector | х1 |
| 14 | decorative plug | х2 |
|---|---|---|
| 15 | top rail connector | х1 |
| 16 | roller | х4 |
| 17 | locking glass | х2 |
| 18 | glass stopper | х4 |
| 19 | self-tapping screw 3.9×9.5 | х8 |
| 20 | self-tapping screw 3.9×32 | х4 |
AM.PM Europe GmbH
Torstrasse 177 D-10115 Berlin
www.ampm-world.com 10/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>