X-MAKER JOY V40-2A35N Creating Toys Better Than Playing User Guide

May 15, 2024
X-MAKER JOY

X-MAKER JOY Quick Guide
CREATING TOYS BETTER
THAN PLAYING

V40-2A35N Creating Toys Better Than Playing

Packing List

X-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Packing
List

Notes

  • AOSEED filaments are recommended. Do not frequently change filaments of various brands to avoid nozzle jamming.
  • Please notice the supported versions when installing X-MAKER App
  • Recommended ambient temp for using the printer is 0-35℃. Please turn off the printer when not in use
    For more information, please visit www.aoseed.com

How to start?

X-MAKER JOY V40-2A35N Creating Toys Better Than Playing - How to
start

  1. Power on X-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Power onNote
    Please keep your hands dry when taking out the power cord.
    Connect the power cord first, then turn on the power switch.

  2. Connect to PrinterX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Connect to PrinterLong press the red button at the back until you hear a prompt beep, and the indicator light turns yellow, indicating a successful reset
    Launch the app. Select X-MAKER JOY, then follow the operations shown in the diagram. Click the ”  Connect Hotspot ” button. Enter the Wi-Fi account and password, and connect to the printer.

  3. Install the filament holderX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - filament holderPlease make sure the filaments are not knotted or intersected before placing the spool on the holder.

  4. Install the filamentX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Install the filamentInsert the tip into the filament inlet until the prefeeder grabs the material. Push the spring upward (as shown by the red arrow in the figure above), to make the filament enter smoothly.

  5. Load the filamentX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Load the filamentAfter connection, go to App Printer-Printer Settings-Filament,and click Load. Wait for the nozzle to heat. Loading is complete when filament comes out.(Make sure the nozzle is clean before printing.)

  6. Place the BaseplateX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - BaseplateEnsure the baseplate is aligned with the heating platform.Keep the baseplate clean and flat after placement.

  7. Model printingX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Model printingCreative U-disk Printable Models Easy-to-use one-press printing with the X-MAKER App

  8. Print completeX-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Print completeAllow the printer to cool down below 45 °C before taking out the model in case of burns.
    Remove the support structures of modelsm using pliers.

X-MAKER App

Download and installation

X-MAKER JOY V40-2A35N Creating Toys Better Than Playing - Download and
installation

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

X-MAKER JOY

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals