SLC S32201 DALI-2 Driver CC Multi 50W DT6 User Manual
- June 13, 2024
- SLC
Table of Contents
SLC DALI-2 Driver CC Multi 50W DT6
User Manual
Important: Read All Instructions Prior to Installation
Function introduction
Product Data
Output | LED Channel | 1 |
---|---|---|
Selectable Current | 350mA | 450mA |
DC Voltage Range | 8-52V | 8-52V |
Selectable Current | 950mA | 1050mA |
1500mA
DC Voltage Range| 8-52V| 8-47V| 8-45V| 8-41V| 8-40V| 8-37V| 8-35V| 8-33V
Current Tolerance| ±5%
Rated Power| Max. 50W
Input| Voltage Range| 200-240V AC
Frequency Range| 50/60Hz
Power Factor (Typ.)| > 0.93
Total Harmonic Distortion| THD ≤ 15% (@ full load / 230VAC)
Efficiency (Typ.)| 87% @ 230VAC full load
AC Current (Typ.)| 0.27A @ 230VAC
Inrush Current (Typ.)| COLD START Max. 2A at 230VAC
Leakage Current| < 0.5mA /230VAC
Control| Dimming Interface| DALI DT6 (DALI consumption<2mA)/ PUSH
Dimming Range| 0.1%-100%
Dimming Method| Amplitude dimming (PWM dimming under 1%)
Dimming Curve| Logarithmic
Protection| Short Circuit| Yes, recovers automatically after fault condition
is removed
---|---|---
Over Voltage| Yes, recovers automatically after fault condition is removed
Over Temperature| Yes, recovers automatically after fault condition is removed
Environment| Working Temp.| -20℃ ~ +45℃
Max. Case Temp.| 75℃ (Ta=”45℃”)
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH
Safety & EMC| Safety Standards| ENEC EN61347-1, EN61347-2-13 approved
Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| EN55015, EN61000-3-2, EN61000-3-3
EMC Immunity| EN61547, EN61000-4-2,3,4,5,6,8,11
Others| MTBF| 191300H, MIL-HDBK-217F @ 230VAC at full load and 25 ambient
temperature
Dimension| 2105032mm (LWH)
Dips to set the operation current
- Dimmable DALI LED driver
- In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2
- Built-in DALI-2 interface, DALI DT6 device
- Amplitude dimming (PWM dimming under 1%), flicker free
- Smooth and deep dimming to 0.1%
- 1 channel constant current output , max. output power 50W
- Dip switches to select operation current from 350mA-1500mA
- Class 2 power supply, full isolated plastic case
- High power factor and efficiency
- Stand-by power consumption less than 0.5W
- Compatible with universal DALI masters that support DT6 commands
- IP20 rating, suitable for indoor LED lighting applications
- 5 years warranty
Safety & Warnings
- DO NOT install with power applied to device.
- DO NOT set operation current with power applied to the device.
- DO NOT expose the device to moisture.
Operation
-
DALI Address Assigned by DALI Masters
DALI address can be assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations. -
Power On Level
Power on level is a DALI parameter that defines the level of a control gear after power is restored. The factory default power on level for this driver is 100, which means the driver will be at 100% intensity when power is restored. -
Push Dimmer Mode
While connected with a AC PUSH, operations under Push Dimmer Mode are as follows:
1.1. Click the button to switch ON/OFF
1.2. Press and hold down the button to increase or decrease light intensity to
desired level and release it, then repeat the operation to adjust light
intensity to opposite direction. The dimming range is from 0.1% to 100%.
1.3. Memory function after power off or power failure enables the device to
memorize the status before power off while power on again.
Wiring Diagram
- With DALI BUS
- With PUSH dimmer
Product Dimension
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>