OTTO OTRLGTST 10 Inch Ring Light Tripod Kit Instruction Manual
- June 4, 2024
- OTTO
Table of Contents
OTTO OTRLGTST 10 Inch Ring Light Tripod Kit
Safety and General Information
Please read all safety instructions before using this product. Improper use of this product may result in damage to this or attached products. To ensure the product works well, please never use the product in the following condition:
- Moist or underwater condition.
- Do not use chemical solvent on cleaning this product.
- Do not subject the device to liquid or attempt to disassemble the device.
- Do not use this product in an aircraft.
- Do not expose the device to direct sunlight, heat or flame.
WARNING
-
ONLY CONNECT USB CORD TO POWER SUPPLY WITH 1A MAX
-
HANDLE WITH CARE, DO NOT USE SHARP METAL OBJECTS.
-
STORE THE UNIT IN A DRY PLACE WHEN NOT IN USE.
-
INDOOR USE ONLY.
Product Specifications
- Model : OTRLGTST
- Officeworks Product Code : OTRLGTST
- Light diameter 10″
- Light temperature: 3200-6000K B62-100mm
- Tripod height: 80-180cm
- Rated input : 5V=1A
- Rated power : 12.5W (Max)
- Power supply: USB 2.0 cable (included)
Assembly Instructions
- Step 1: Prepare the folded tripod stand.
- Step 2: Loosen the screw knob anticlockwise
- Step 3: Use both hands to pull the stand legs open.
- Step 4: Adjust the stand legs then tighten the screw knob
- Step 5: Loosen the screw knobs on the middle pole and the top pole.
- Step 6: Pull the poles up to the height (max 1. m) you want and tighten the knobs
- Step 7 : Install the tripod ball-head on the tripod and tighten IT
- Step 8: Install the ring light and the phone holder on the ball head head and tighten it.
- Step 9: Loosen the ball-head knob to adjust the right light then tighten, assembly completed
Function
- Increase brightness
- Light mode
- Decrease brightness
- On/off
- Phone holder
- LED light
- Tripod
- Main pole
- DLOcking device
- Ball head
The height is adjustable, loosen the locking device to adjust it and tighten it whenever needed. The LED light has 3 light modes with 10 adjustable brightness levels.
Packing Accessories
- 10″ LED Ring Light with USB cable x 1
- Phone cradle x 1
- Phone cradle holder x 1
- Connector piece x 1
- Tripod x 1
- Instruction manual x 1
(Smartphone device and power adaptor are not included.)
Product Warranty
Valid for Australian Customers Only
Officeworks Ltd warrants that this product will be free from defects and work
as intended for 3 years from the date of purchase by the original customer.
If the product has any defects or does not work as specified during the
Warranty Period, Officeworks will, at its election and at its expense, repair
or replace the product.
This warranty does not apply:
- to cosmetic damage;
- to damage caused by consumables used in connection with the product ;
- where the product has not been used in accordance with all provided instructions;
- to damage arising from fair wear and tear;
- where the product has not been subject to reasonable use;
- where the product has been intentionally or negligently damaged; and/or
- if the customer has attempted to repair the product
To make a claim under this warranty, please return your product with your
receipt or proof of purchase to your nearest Officeworks store or contact 1300
633 423.
This warranty is provided in addition to any rights you may be entitled to
under the Competition & Consumer Act 2010. Our goods come with guarantees that
cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure
OFFICEWORKS LTD 236-262EAST BOUNDARY ROAD EAST BENTLEIGH VIC 3165 AUSTRALIA
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>