VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs Instructions

June 13, 2024
VINGLI

VINGLI logo Loft Bed

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs Thank you for your purchase.
Please contact us if you have difficulty with assembley or need replacement parts.
VINGLI Customer Service is here to assist you.
Email: support@vingli.com
Please attach your User Name or Order ID so that we can assist you better.

Introduction

Guide of Manual

  • Please read the following instruction carefully and use the product properly.
  • Please keep this manual and hand it over when you transfer the product.
  • Please contact us when further information and help needed.

Notes

  • Make sure to start on the correct instruction page for the bed configuration you are assembling.
  • Unpack parts and hardware carefully to prevent scratching of lacquered components.
  • Please assemble the product according to the steps on the diagram strictly.
  • Do not fully tighten the screws until all pieces are situated in place.
  • For continued use, it’s suggested you regularly check the tightness of bolts and connections to ensure safety.
  • Do not assemble and disassemble the product repeatedly to avoid damaged.
  • To avoid confusion keep all parts and hardware together with the boxes that they came in; some bed configurations require multiple boxes.

SAFETY WARNING:

  1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.
  2. Always use the recommended size mattress or mat tress support, or both, to help prevent the likelihood of entrapment or falls.
  3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
  4. Do not allow children under 6 years of age to use the upper bunk.
  5. Periodically check and ensure that the guardrail, ladder, and other components are in their proper position, free from damage, and that all connectors are tight.
  6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
  7. Always use the ladder for entering and leaving the upper bunk.
  8. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
  9. Use of a night light may provide added safety precau tion for a child using the upper bunk.
  10. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and wall.
  11. The use of water or sleep flotation mattresses is prohibited.
  12. Keep these instructions for future reference.

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - parts
1

Assembly Steps

STEP 1 Assemble Ladder

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - STEP
1

Assembly method:

  1. Insert Screw (A) through a step holder on Ladder Rail (6) to secure Ladder Step (7) to the rail (Notice: The welding joint should face downward and make sure the contact surface of Ladder Step (7) and Ladder Rail (6) is smooth and even.)
  2. Remove the release liner of the double-sided tape on the back of Rubber Tread Cover (13) and attach it to Ladder Step (7)
CODE HARDWARE QTY
A 8

STEP 2 Assemble Side Guard Rail and Post (With Ladder)

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - STEP
2

Assembly method:

  1. Mount Screw (B) and Washer (D) to the hole on Post (10&11) to attach the top of Side Guard Rail (2), then use Screw (C) and Washer (E) to attach the bottom of Side Guard Rail (2) to Post (10&11).
  2. Use Screw (C) and Washer (E) to attach Short Spreader Bar (3) to Post (10&11).
  3. Install the ladder in Step 1 to Side Guard Rail (2) and Short Spreader Bar (3) use Screw (A) to secure.
CODE HARDWARE QTY
A 8
B 2
C 4
D 2
E 4

STEP 3 Assemble Side Guard Rail and Post

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - HARDWARE
7

Assembly method:

  1. Mount Screw (B) with Washer (D) to the hole on Post (10&11) to attach the top of Side Guard Rail (1)
  2. Use Screw (C) with Washer (E) to attach the bottom of Side Guard Rail (1) to Post (10&11).
  3. Use Screw (C) with Washer (E) to attach Short Spreader Bar (4) to Post (10&11).
CODE HARDWARE Qry
B 2
c 4
D 2
E 4

STEP 4 Assemble Long Guard Rails

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - STEP
4

Assembly method:
Insert Screw (A) through the holes on the upper part of Long Guard Rail (5) and Post (10&11), then use Screw (C) and Washer (E) to attach Post (10&11) to Long Guard Rail (5). Both long guard rails at the front and back install in the same way.
NOTE:
Please check the correct direction of plastic slots as shown in the picture before assembly. Tighten screws finger-tight only at this step.

CODE HARDWARE QTY
A 4
C 8
E 8

STEP 5 Assemble the Back Side Long Spreader Bar

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - STEP
5

Assembly method:

  1. Insert Screw (C) and Washer (E) to the center and bottom holes on Post (10) to attach Long Spreader Bar (9)
  2. Tighten all screws on the bed frame further.
CODE HARDWARE QTY
C 4
E 4

STEP 6 Install Bed Slats

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - STEP
6

Assembly method:
Push Slat (8) to plastic slots as shown in the picture.
If you fail to insert Slat (8) into the slot, please make sure the direction of plastic slots is correct following Step 4.

STEP 7 Secure Bed to the Wall

VINGLI G13004389 Twin Metal Loft Bed Frame with Stairs - STEP
7

Assembly method:
Attach bed to the wall for extra stability by using Connector (12) with Expansion bolt (F) and Screw (G). This step is optional.

CODE HARDWARE QTY
F 4
G 4

VINGLI logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals