ONFORU BDB36G-3 PIR LED Wall Lights with Motion Sensor Instruction Manual
- June 13, 2024
- ONFORU
Table of Contents
ONFORU BDB36G-3 PIR LED Wall Lights with Motion Sensor
Product Information
This product is a light fixture that is designed for installation in an electrical system. It is important to follow the preparation and installation steps provided in this manual to ensure safe and proper usage of the product.
Preparation
Risk of Shock: Before beginning installation,it is crucial to turn off electricity at the circuit breaker box or the main fuse box. This precautionary measure helps to prevent electric shock during the installation process.
Note: When connecting wires, it is essential to use wire nuts/connectors that are rated for the correct gauge and number of wires used. Additionally, ensure that there are no exposed wire bundles outside the wire nut/connector, and take care not to damage or cut the wire insulation (covering) during installation. Avoid letting the wires touch any sharp edges.
Warning: Do not connect this light fixture to an ungrounded electrical system. It is necessary to attach the ground fixture wire to either the green ground screw on the mounting plate or the ground wire in the outlet box. Failure to ground the fixture may result in electric shock if any wires or wire connections are damaged or loose, potentially causing injury or death.
Installation Steps
- For wet locations, ensure that the gap between the EVA gasket and mounting surface is filled completely with sealing compound or silicone glue.
- Follow steps 8, 9, and 10 provided in the user manual for the detailed installation process.
Tbroubleshooting
| Malfunction | Cause | Remedy |
|---|---|---|
| The light does not light up when the LED senses movement | 1. The light is not |
energized
2. Other surrounding light sources make the light misjudge it as
daytime
3. During the day, the brightness is in night mode
4. Internal wiring is loose| 1. Check power-on status
2. Turn off nearby lights or sensor head to other directions
3. Reset
4. Rewire after power failure
The LED sensor light continues to light up even when there is
no movement| Check the relevant area and retune or override the sensor head
if necessary
The LED sensor light illuminates during the day| –| 1. Do not cover the
sensor head
2. Place the light in a place where the light is bright enough
during the day
The LED sensor light is flashing| The shadows around the sensor make it
mistakenly think it’s
night
Surrounded by other unstable light sources shining onto the
induction| Avoid being exposed to such light sources
The LED lights turn on unexpectedly| 1. Wind blows branches and bushes within
the sensing
range
2. Sensing cars on the road
3. Sudden temperature change due to climate factors or fans,
exhaust from open windows| 1. Adjust its scope
2. Adjust its scope
3. Change irradiation area
COMPONENTSAND STRUCTURE
- Cover
- LED Light Source
- Lamp Bracket
- Sensor Head
PARTS LIST
SPECIFICATIONS
Note:
The testing standard of the product’s luminous flux: Place the three/two
lights on the same horizontal surface for testing, and the tested luminous
flux is the accurate luminous flux.
Operation Instructions
- SENS adjustable: It can be adjusted according to using location; low sensitivity with 5m for detection distance; high sensitivity with 10m, it fits for large room.
- Can identify daay and night: The consumer can adjust work ambient light. It can work in the daytime and at night when it is adjusted on the “+” position (max). It can work in the ambient light less than 10LUX when it is adjusted on the “_” position (min).
- Time-delay adjustment: It can be set according to the consumer’s desire. The minimum time is 10sec 3sec. The maximum is 7min 2min. Time-delay is added continually: When it receives the second induction signals after the first induction, it will compute time once more on the rest of the first time-delay basic (set time).
OPERATION INSTRUCTIONS
Detection Range: 180°
NOTE:
- The PIR sensor shall always be tilted slightly downward.
- The orientation angle of the sensor shall be between 0-45°.
RECOMMENDED INSTALLATION HEIGHT: 6.5-13.1 feet above the ground.
- When mounted 8ft above the ground and the sensor is oriented horizontally, the maximum sensing distance is about accc72ft.
- When mounted 8ft above the ground and the sensor is 45° down, the minimum sensing distance is about 19ft.
Note: The detection distance of the sensor is the farthest when the ambient temperature is 25 C.
Any temperature fluctuations above or below 25 C will affect the detection
distance.
If the light continues to detect motion while it is on, it will remain on
until the motion stops.
The sensor will be more sensitive to motion across the motion towards it directly.
PREPARATION
RISK OF SHOCK:
BEFORE BEGINNING INSTALLATION, TURN OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX
OR THE MAIN FUSE BOX.
NOTE:
BE SURE TO USE WIRE NUTS/CONNECTORS RATED FOR THE CORRECT GAUGE AND NUMBER OF
WIRES USED.
MAKE SURE THERE ARE NO EXPOSED WIRE BUNDLES OUTSIDE THE WIRE NUT/CONNECTOR (IF
APPLICABLE).
BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULATION (COVERING) DURING
INSTALLATION. DO NOT LET THE WIRES TOUCH ANY SHARP EDGES.
WARNING:
DO NOT CONNECT THIS LIGHT FIXTURE TO AN UNGROUNDED ELECTRICAL SYSTEM. ATTACH
GROUND FIXTURE WIRE TO EITHER GREEN GROUND SCREW ON MOUNTING PLATE OR THE
GROUND WIRE IN THE OUTLET BOX.
INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY CAUSE THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH.
INSTALLATION STEPS
FOR WET LOCATION, MAKE SURE FILL FULL THE GAP OF EVA GASKET AND MOUNTING SURFACE WITH SEALING COMPOUND OR SILICONE GLUE
Note:
The raised part (RA) of the metal plate must be engaged with the recessed part
(RE) of the base,otherwise it cannot be installed.
Troubleshooting
HK Bright International Lighting Co., Limited
Unit 616, 6/F., Kam Teem Industrial Building, 135
Connaught Road West, Sai Wan Hong Kong
Manufacturer/Hersteller: MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos Nicosia
Cyprus
UK Importer: MDH LIGHTING LTD
69 Aberdeen Avenue,Cambridge CB2 8DL,United Kingdom
Made in China
support@onforuled.com
www.onforuleds.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>