VEVOR 0.98 inch-25mm Button Maker Machine Instruction Manual

: June 13, 2024
: VEVOR

Table of Contents

VEVOR 0.98 inch-25mm Button Maker Machine
SAFETY REMINDER
COMPONENTS
INSTALLATION STEPS
MODEL AND PARAMETER
FAILURE AND TROUBLESHOOTING
Documents / Resources

VEVOR 0.98 inch-25mm Button Maker Machine

SAFETY REMINDER

This badge machine is only applied for the intended purpose. Don’t apply in other applications which exceed safety considerations.
Children cannot operate this product unless accompanied by an adult.
Pay attention to safety during operation, and avoid crushing fingers.

COMPONENTS

INSTALLATION STEPS

MODEL AND PARAMETER

Product Model

Model

| ****

JMB- 25

| ****

JMB- 32

---|---|---
Manufactured Badge

Specification

Copper Plate Paper

| 127-157g

Copper Plate Paper

Accessories With Machine| 1. Φ25 Metal back plate 250 Φ25 Plastic back plate 250

2. Φ25 Tin Up Cover *500

3. Φ25 White paper *20

4. Φ25 Transparent plastic film *500

5. Φ25 Round Cutter * 1

6. Allen Key * 2

7. Magic Book *1

8. Instruction *1

| 1. Φ32 Metal back plate 250 Φ32 Plastic back plate 250

2. Φ32 Tin Up Cover *500

3. Φ32 White paper *20

4. Φ32 Transparent plastic film *500

5. Φ32 Round Cutter * 1

6. Allen Key * 2

7. Magic Book *1

8. Instruction *1

Product Model

Model

| ****

JMB- 58

---|---
Manufactured Badge

Specification

| Φ58
Machine Body Color| Black
Paper Requirements| 127-157g

Copper Plate Paper

Accessories With Machine| 1. Φ58 Metal back plate 50 Φ58 Plastic back plate 50

2. Φ58 Tin Up Cover *100

3. Φ58 White paper *20

4. Φ58 Transparent plastic film *100

5. Φ58 Round Cutter * 1

6. Allen Key * 2

7. Magic Book 1 8.Washer 1

9. Instruction *1

FAILURE AND TROUBLESHOOTING

Failure Appearance	Possible Reasons	Troubleshooting
First time downward press iron cover and not absorbed to up mold	1.

Unsuitable operating method

2. Too much lubricating oil in the up mold

| 1. First time downward press up mold hinge is in a separate state

2. Use clean cloth or tissue completely wipe it if found too much lubricating oil on the up mold

3. The up and down mold must be on

the same vertical line when closing

Second downward press part not wrapped in| 1. Unsuitable operating method

2. Unsuitable paper thickness

3. Up mold screws loosen

| 1. The up and down mold must be on the same vertical line when closing

2. Use the stipulated thickness paper

3. Place the up mold on the machine body, use the complimentary Allen key to fix the screws in the up mold internal hole center.

Not tightly press the badge, pressed in but not firm| 1. The downward press is not in place, not press to the bottom

2. Paper is thinner

3. ( 25mm ) Configured metal back consumables do not place the washer

| 1. Need press to the bottom when downward pressing

2. Change to use a slightly thicker paper

3. Right side mold place 2mm thickness washer when using the metal back consumables

Up mold unable to lift up after pressing manufacture, blocked| 1. Up and down mold position deviated

2. The paper is incorrectly cut round or blocked by a foreign object.

| Use a sharp tool (such as a straight screwdriver) to align to middle merge position clearance which is between up and down mold, and pry open with the object like a hammer (Attention: Just tap it, generally, it

will not be too tightened).

Address : Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA : Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Technical Support and E-Warranty Certificate
www.vevor.com/support

Documents / Resources

| VEVOR 0.98 inch-25mm Button Maker Machine [pdf] Instruction Manual
0.98 inch-25mm Button Maker Machine, 0.98 inch-25mm, Button Maker Machine, Maker Machine, Machine
---|---