GE Lighting CYNC Smart Temperature Sensor Smart WiFi Thermostat Sensor Humidity Sensor User Guide
- June 13, 2024
- GE Lighting
Table of Contents
GE Lighting CYNC Smart Temperature Sensor Smart WiFi Thermostat Sensor
Humidity Sensor
Connecting Your Thermostat
Complete the installation and setup of your Cync App & Thermostat before setting up your Sensor
STEP 1 Open the Cync App, powered by Savant.
STEP 2 Follow the setup instructions in the Cync App. Keep your Sensor handy as you’ll need to scan the QR code or enter the PIN to complete setup.
For installation or setup help, visit cyncsupport.gelighting.com or call l-8Lili-302-2Li93
lnStalling Your Sensor
Set up in the Cync App before mounting to access the QR code and PIN. You’ll need a Phillips Screwdriver, Pencil, Drill with 3/16″ Bit & Tape Measure.
- STEP 1 Remove plastic battery tab before installing.
- STEP 2 Find a location for your Sensor. Place on a wall L,8″-60″ from the floor and away from direct sunlight and air vents.
- STEP 3 Mark the hole location.
- STEP 4 Drill a hole using a 3/16″ drill bit and insert anchor.
- STEP 5 Insert screw leaving about 1/8″ spacing between the screwhead and wall.
- STEP 6 Mount the Sensor by sliding the eyehole over the screwhead.
Optional Mounting: Use the provided adhesive to adhere to the wall. Make sure not to cover the QR code or PIN.
Ready for a New Sense-sation?
Reduce Hot Spots &
Drafty Spaces.
Place a Sensor where the temperature is warmer or colder than the rest of the
house. Use the Cync App to average temperature between the Thermostat and
Sensor.
Enhance Comfort in Your Most Important Rooms.
Your Sensor can adjust the temperature to the room it is in. Install multiple
Sensors (sold separately) in different rooms and create a schedule in the Cync
App to adjust the temperature to the room you are in during different times of
day.
Support Your Sleep/Wake Cycle.
Place a Sensor in your bedroom and set a schedule in the Cync App to cool vour
room before bedtime and warm up in the morning. Take your sleep space to the
next level by creating an evening and morning scene for your Cync Smart Lights
(sold separately).
Battery Replacement
- STEP 1 Remove the Sensor from the wall.
- STEP 2 Using a small Phillips screwdriver, remove the screw and then the back cover.
- STEP 3 Remove old battery.
- STEP 4 Install one new CR2032 battery.
- STEP 5 Replace back cover.
- STEP 6 Remount to wall.
WARNING Chemical Burn Hazard – Do not ingest or swallow coin cell battery. This sensor contains a coin cell battery. If the coin cell battery is swallowed or ingested, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used coin cell batteries away from children. If the battery compartment does not close securely, stop using the remote control and keep away from children. If you think coin cell batteries have been swallowed or placed inside any part of the body, seek immediate medical attention.
FCC
FCC ID: PUU-CWLMSONNWWI
IC: 10798A-CWLMSONNWW1
Suitable for Dry locations. This device complies with Part 15 of the _F_CC
Rules . Operation is subject to the following two conditions: (I) this .
device may not cause harmful interference, and (2) this device must accept any
interference received, induding interference that may cause undesired
operation. Any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment. NOTE:
This equipment has been _tested and found to comply with the limits for a
Class B d1g1tal device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residenti_al install_ation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used In accordance with the
instructions, may cause harmful interference to radio communications. However,
there Is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the 1nter_ference by one or more
of the following measures: reorient or relocate the receiving antenna,
increase the separation between the equipment and receiver connect the
equipment into an outlet on a circuit differe?t from that to which the
receiver is connected, or consult the dealer or an experienced radio/TV
technician for help.
This device complies with CAN ICES-3(B)/NMB-3(B)
RF Exposure Information: This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. In order to avoid the
possibility of exceeding the FCC radio frequency exposure limits human
proximity to the antenna shall not be less than’ 8 inches during normal
operation.
RF Exposure Statement: This equipment complies with ISED RSS-102 radiation
exposure limits set forth for an uncontrolled environment. This transmitter
must be installed to provide a separation distance of at least 8 inches from
all persons and must not be collocated or operating in conjunction with any
other antenna or transmitter.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
FCC Supplier’s Declaration of Conformity Model: CWLMSONNWWI This device
complies with part 15
of the FCC Rules. Operation is subject to the following two conditions: (I)
This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation. GE Lighting, a Savant company, 1975 Noble Road,
Cleveland ‘ OH ‘ gelighting.com/cync
GE and C by GE are trademarks of General Electric Company. Used under trademark license.
Like your new Room Temperature Sensor?
Share your experience!
Leave a review where you purchased the product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>