VIVO MOUNT-CAR02 Car Tablet Mount Instruction Manual
- June 13, 2024
- Vivo
Table of Contents
VIVO MOUNT-CAR02 Car Tablet Mount
Product Information
Product Name | Car Tablet Mount |
---|---|
SKU | MOUNT-CAR02 |
Weight Capacity | Tablet Mount: 5.5lbs (2.5kg), Arm: 11lbs (5kg) |
Product Usage Instructions
Package Contents
Item | Quantity |
---|---|
Base | 1 |
Arm | 1 |
Pole | 1 |
Knob | 4 |
Cable Clips | 2 |
Support Screw | 2 |
Connecting Bracket | 1 |
Screw Cap | 2 |
Adapter | 1 |
M6x10mm Screw | 4 |
M6 Washer | 8 |
M4x16 Thumbscrews | 6 |
M4 Washers | 4 |
M6 Nut | 2 |
M6 Flanged Nut | 1 |
M6x45mm Screw | 1 |
5mm Allen Wrench | 1 |
Wrench | 1 |
TOOLS NEEDED
Assembly Steps
-
Step 1
Begin by identifying what foot style is needed for your passenger seat configuration, using the images below. Please note that the two front seat bolts of some vehicles will differ from each other in angle.Attach the appropriate foot for the passenger seat’s left bolt [ 0° Foot (B), 90° Foot (C), or 45° Foot (D) ] to the left underside of of Base (A) using M6x10mm Screws (S-A), M6 Washers (S-B), and a Phillips screwdriver.Install compatible Foot (B, C, D) for your passenger seat’s left bolt to the threads on Connecting Bracket (L) using M6 Nuts (S-C), M6 Washers (S-B), and Wrench (T-B). Please note, based on your passenger seat’s floor bolts, you may need a different foot than what was used above . -
Step 2
Loosely assemble the right foot assembly to Base (A) using M6x10mm Screws (S-A), M6 Washers (S-B), and a Phillips screwdriver. Align the left foot with the left seat bolt on the passenger seat. Adjust the right foot to match up with the right bolt on the seat and tighten M6x10mm Screws (S-A). -
Step 3
Loosen the front seat bolts on passenger seat using a socket wrench (size needed depends on manufacturer). Slide the left foot under the left seat bolt and the right foot under the right seat bolt. Adjust the placement as needed and re-tighten bolts. -
Step 4
Attach Pole (F) to back of Base (A) using Knobs (I). -
Step 5
Thread Support Screws (K) onto Base (A) and place Screw Caps (P) onto the ends once threaded. -
Step 6
- Slide Arm (G) onto Pole (F) with the adjustment bolt pointing up. Tighten and secure with 5mm Allen Wrench (T-A). Adjust the arm tension using 5mm Allen Wrench.
- Determine desired Pole (F) height and Insert M6x45mm Screw (S-J) into slot. Secure using M6 Flanged Nut (S-I), making sure the flanged, wider part of the nut is faing outward, with the hex side fitting into the hex indention on Pole (F).
-
Step 7
Mount the Adapter (K) to the Arm (F) using the M4x16mm Thumbscrews (S-F) with M4 Washers (S-G) in mounting holes. Loosely install remaining M4x16mm Thumbscrews (S-F) into the top adjustment holes in Adapter. Place Cable Clips (H) on Arm (F) to manage cables. -
STEP 8
If assembled mount feels unlevel, tighten Support Screws (I) to level out. Note: Before continuing, we recommend checking that your tilt joint on your VESA mount is tight.
To adjust the Adapter (K) to fit the device, push device down onto springloaded tabs and position device against the face of the adapter. With the M4x16mm Thumbscrews (S-F) adjustment screws still loose, center the device on the adapter. Then tighten the M4x16mm Thumbscrews (S-F) adustment screws. -
STEP 9
To remove the device, while holding both sides of the device, pull down, tilt the devide, then lift it out. Reinstall the device in reverse order
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PART S – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
www.vivo-us.com
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Car Tablet Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>