clinton electronics CE-CM-LX-9 9 Inch Telescoping Ceiling Mount LCD-PVM Pole Installation Guide

Clinton Electronics CE-CM-LX-9 9 Inch Telescoping Ceiling Mount LCD-PVM

Pole

Telescoping Monitor Pole

The Telescoping Monitor Pole is designed to mount a monitor or PVM from the ceiling steel support truss or channel strut structure. It is not designed to be mounted to a wooden surface and should only be used with the maximum weight indicated. Using it with products heavier than the maximum weight may result in instability and possible injury.

Product Usage Instructions

1. Secure to Building Structure:
   The pole should be secured to a steel truss or strut channel with a minimum thickness of 22 Ga. There should be a maximum gap of 1 between the pole and the structure.

2. Adjust Height:
   While supporting the pole from the bottom end, loosen the twist-lock collar by turning it counterclockwise. Gently lower the pole to the desired height. Once adjusted, lock the pole in position by rotating the twist-lock collar clockwise. Hand tighten the collar as snugly as possible to prevent the pole from dropping down.

3. Install Rivet:
   After setting the pole to the desired length, drill a 3/16 hole through one side of the inner pole at the pre-drilled hole location in the outer pole. Insert the rivet until the backside of the head is flush with the outer surface of the pole. Strike the pin sharply with a hammer to expand the rivet. For three-section poles, repeat this step for each section of the pole.

4. Route Safety Cable:
   Loop the safety cable around the truss or a secure member of the building structure. Tighten the nuts on the included wire clamp using a 5/16 wrench. Feed the eyelet end of the cable into the slotted hole near the top of the pole and down through the bottom of the pole.

5. Route Cables:
   Feed the eyelet end of the safety cable, along with the desired power and video cables, through the slotted hole near the top of the pole and down through the bottom of the pole.

6. Attach VESA Plate:
   Place the VESA plate on the backside of the monitor with the UP indicator oriented towards the top. Tighten the four M4 Phillips head screws into the 75mm or 100mm hole pattern.

7. Attach Receiver Bracket:
   Slide the Receiver Bracket over the bottom end of the pole, aligning the slot and square hole in the bracket to the holes on each side of the pole. The square cutout should be positioned on the bottom end of the pole. Slide two carriage bolts into the side and through the bracket & pole. Place a washer on the opposite side of each bolt and securely fasten a lock nut onto each bolt using a 7/16 wrench.

For any further support or information, please contact Clinton Electronics at 800.549.6393 or visit their website at www.clintonelectronics.com.

Included Items

• Telescoping Pole
• Receiver Bracket
• Mounting Hardware
• Rivet(s)
• Safety Cable
• VESA Plate(s)

Required Items

• Phillips Head Screwdriver
• Drill with 3/16” Drill Bit
• 3/4“ Wrench
• 5/16” Wrench
• 7/16” Wrench
• Hammer

USE ONLY AS DESIGNED
ATTENTION!
THIS MOUNT IS DESIGNED TO MOUNT A MONITOR OR PVM FROM THE CEILING STEEL SUPPORT TRUSS OR CHANNEL STRUT STRUCTURE. IT IS NOT DESIGNED TO MOUNT TO A WOODEN SURFACE. IT IS INTENDED FOR USE ONLY WITH THE MAXIMUM WEIGHT INDICATED. USE WITH PRODUCTS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.

INSTRUCTIONS

1. Secure to Building Structure

2. Insert threaded rod between truss gap or into hole in channel strut.

3. Place 1/2″ fender washer over the threaded rod and then 1/2″ lock nut.

4. Tighten the 1/2″-13 lock nut using a 3/4″ wrench.

5. Adjust Height
   While supporting the pole by the bottom end, loosen the twist-lock collar by turning it counterclockwise. Extend the pole by gently lowering it to the desired height.
   Once the height of the pole has been adjusted, lock the pole in position by rotating the twist-lock collar clockwise. The collar should be hand-tightened as snug as possible to prevent the pole from extending (dropping down).

6. Install Rivet
   After the pole is set to its desired length, drill a 3/16” hole through one side of the inner pole at the pre-drilled hole location in the outer pole. Insert the rivet until the backside of the head is flush with the outer surface of the pole. While supporting the backside of the pole, strike the pin sharply with a hammer to expand the rivet.
   *Three-Section poles only: Poles with three tube sections require two rivets to be installed, one for each section of telescoping pole length, (one above each locking collar). Repeat the steps above for each section of pole.

7. Route Safety Cable
   Loop the safety cable around the truss or nearby secure member of the building structure, and tighten nuts on the included wire clamp with a 5/16” wrench.˜ Feed the eyelet end of the cable into the slotted hole near the top of the pole and down through the bottom of the pole.

8. Route Cables
   Feed the eyelet end of the safety cable, and the desired power and video cables through the slotted hole near the top of the pole and down through the bottom of the pole.

9. Attach VESA Plate
   Place the VESA plate on the backside of the monitor. The “UP” indicator should be oriented towards the top of the monitor. Tighten the four M4 Phillips head screws into the 75mm or 100mm hole pattern.

10. Attach Receiver Bracket
    Slide the Receiver Bracket over the bottom end of the pole, and align the slot and square hole in the bracket to the holes on each side of the pole.
    The square cutout should be positioned on the bottom end of the pole.
    Slide the two carriage bolts into the side and through the bracket & pole. Place a washer on the opposite side of each bolt and using a 7/16” Wrench, securely fasten a lock-nut onto each bolt.

11. Hang Monitor
    With the VESA plate secured to the monitor, slide the receiving hooks onthe VESA plate over the tabs on the receiver bracket at the end of the pole.

12. Attach VESA Retaining Screw
    Screw the remaining 6mm long M4 screw through the backside of the receiver bracket, and into the threaded center hole in the VESA plate

13. Attach Safety Cable
    Attach the eyelet end of the safety cable to the monitor by securing the 10mm long M4 screw through the safety cable’s eyelet, and into an available M4 hole in the monitor. If no other M4 holes are available in the monitor, remove one of the screws from the VESA plate, and replace it with the safety cable’s screw.

14. Adjust Angle
    To adjust the angle of the monitor, loosen the upper locknut on the side of the Receiver Bracket with a 7/16” Wrench. Once the desired angle is set, ensure both upper and lower lock-nuts are firmly tightened.

15. Level the Pole

16.  You can ensure the pole is plumb by tightening the 1/4”-20 lock nuts on the top of the pole where it attaches to the structure using a 7/16” wrench.

17. Place a level on the pole and tighten the nuts that correspond to the direction that the pole needs to move (see illustration on the lower-right).

18. Check and adjust 2 adjacent sides of the pole until it is plumb in each direction.

clinton electronics | 6701 Clinton Road Loves Park, IL 61111 | 800.549.6393 (Support) | www.clintonelectronics.com
*Information in this document is subject to change without notice

References

• Clinton Electronics - CCTV, Public View Monitors and Displays

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>