Clinton Electronics CE-PTZ10XHD HD-SDI Indoor Recess Mount PTZ Installation Guide
- June 9, 2024
- Clinton Electronics
Table of Contents
- Included Items
- Required Items
- REMOVE TOP COVER & LENS COVER
- SET DIP SWITCHES
- Address ID Number
- Settings
- SET TERMINATION SWITCH
- CONNECT CABLES
- RS-422/RS-485 Connection
- ATTACH MOUNTING PLATE
- ATTACH MOUNT ARM
- REPLACE TOP COVER
- CONNECT SAFETY LEASH
- CONNECT WIRING HARNESS
- CLOSE & LOCK CAMERA TO BRACKET
- CUSTOMER SUPPORT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Clinton Electronics CE-PTZ10XHD HD-SDI Indoor Recess Mount PTZ
Included Items
- Camera xl
- Mount Arm x 1
- Mount Arm Silicone Gasket x 1
- Mounting Plate x 4
- Mounting Plate Silicone Gasket x 1
- Cable Harness x 1
- Installation Manual x 1
- T20 Security Torx Wrench x 1
- 1-1/2″ Phillips Head Screws x 4
- Mount Arm Screws x 3
- Cable Access Hole Plugs x 2
- Plug Tightening Tool x 1
Required Items
- Power Supply
- PTZ Keyboard
REMOVE TOP COVER & LENS COVER
a. Use the T20 security torx wrench to remove the four top cover screws, and remove the cover.
b. Peel off the tape which holds the camera lens in place, then remove the lens cover from the lens.
SET DIP SWITCHES
Before installing the camera, set the camera address, and protocol settings with the dip switches. Address ID and Settings dip switches can be found on the interior of the camera housing after removing the top cover.
Address ID Number
The first set of numbered switches corresponds to the device’s address ID number. When a combination of switches are set to on, the ID number will be the sum of those switches. To confirm the ID number, it will appear on-screen during the initial information boot up screen. Camera IDs can be set from 1-255.
SWITCH# | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
---|---|---|---|---|---|---|---|---|
ID# | 1* | 2 | 4 | 8 | 16 | 32 | 64 | 128 |
*Indicates default setting
Settings
The second set of numbered switches corresponds to the PTZ’s settings .
PROTOCOL | 1 | 2 |
---|---|---|
CLINTON* | OFF | OFF |
PELCO-D | OFF | ON |
PELCO-P | ON | OFF |
AD | ON | ON |
BAUDRATE | 3 | 4 |
--- | --- | --- |
2400 | OFF | OFF |
4800* | OFF | OFF |
9600 | OFF | ON |
19200 | OFF | ON |
38400 | ON | OFF |
57600 | ON | OFF |
115200 | ON | ON |
NTSC/PAL | 6 | |
--- | --- | |
PAL | ON | |
NTSC* | OFF | |
COMM. | 7 | |
--- | --- | |
RS-485 | ON | |
RS-422* | OFF |
Dip switch 8 is disabled on this model.
*Indicates default setting
SET TERMINATION SWITCH
The device which is connected at the end of the line must have the cable communication terminated. Without proper termination, there is potential for control signal errors. The termination dip switch can be found on the bottom side of the camera body.
TERMINATION
TERMINATED| ON
NOT TERMINATED*| OFF
*Indicates default setting
CONNECT CABLES
Before the camera can be installed, you will need to connect the power, video, and communication cables to the PTZ’s wiring harness.
RS-422/RS-485 Connection
The PTZ can be controlled by an external device or control system such as a keyboard or DVR using the RS-485 half duplex, or RS-422 duplex or simplex serial communication signals. Connect Rx+ and Rx- on the PTZ communication cable to Tx+ and Tx- on the controller. Total length of the cable should not exceed 3,900 feet.
ATTACH MOUNTING PLATE
a. If mounting to a flat surface, affix the included mounting plate
silicone gasket to the back side of the mounting plate.
b. Route the cable through the top, or bottom cable access hole, or
through the center of the mounting plate. Cover any unused cable hole with the
included hole plugs.
c. Depending on your mounting surface, attach to the plate to the
mounting surface using either the four included 1-1/2″ Phillips Head screws,
or use other appropriate fasteners (not included). If mounting to a double
gang box, use the correct hardware for the box.
ATTACH MOUNT ARM
a. Affix the included mount arm silicone gasket to the back side of the
mount arm.
b. Route the cable through the arm.
c. Attach the mount arm to the mounting plate using the three included
T20 security Torx screws, or if mounting the arm without the mounting plate,
use the included 1-1/2″ Phillips head screws, or other appropriate hardware.
REPLACE TOP COVER
Reattach the top cover to the camera base, and secure using the four T20 Security Torx screws.
CONNECT SAFETY LEASH
Pull the safety leash from the inside rim of the mount arm and connect the leash to the hook on the base of the camera body.
CONNECT WIRING HARNESS
Plug the end of the wiring harness into the port on the top of the camera body. Do not force the plug into the port; the plug can only be inserted one way. Insert HD-SDI and analog plugs into their respective connections.
CLOSE & LOCK CAMERA TO BRACKET
a. Align the notch on the camera body to the triangle on the front center
of the mount arm.
b. Rotate the camera body clockwise until the notch on the camera body
aligns with the triangle on the mount arm cover.
c. Tighten the Phillips head screw on the top of the mount arm to lock
the camera to the bracket.
CUSTOMER SUPPORT
Clinton electronics I 6701 Clinton Road Loves Park, IL 61111 I 800.549.6393 (Support) I www.clintonelectronics.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>