Clinton Electronics S8 IDX Series Camera Installation Guide

June 9, 2024
Clinton Electronics

Clinton Electronics S8 IDX Series Camera Installation Guide
Clinton Electronics S8 IDX Series Camera

Included Items

  • IDX Series Camera x 1
  • Mounting Plate x 1
  • 4x2Omm Screws x 4
  • Instructions x 1
  • Test Monitor BNC Lead x 1
  • Mounting Template x 1

Required Items:

  • Phillips Head Screwdriver or Drill with Phillips Head Bit

Optional Items:

  • CE-REMOTE (OSD Remote Control)

INSTALL MOUNTING

PLATE Secure the Mounting Plate to a compatible conduit box (Single Gang, Double Gang, 3-1/4″ & 3-1/2″, or 4″ Oct/Rd) using the screws that came with the conduit box, or mount to a solid surface using the 4 screws included with this camera.
INSTALL MOUNTING

NOTE: It is recommended to use drywall anchors if mounting to drywall. Drywall anchors not included.

REMOVE DOME COVER

Hold the dome cover with one hand while gripping the finger grip tabs on the bottom of the camera base. Turn the finger grip tabs (camera base) counter- clockwise to separate it from the dome cover.
REMOVE DOME COVER

CONNECT CABLES

Make connections to the BNC cable and the power connection. Feed any cable slack into the mounting surface. A Power LED (on the circuit board) will illuminate GREEN when the camera is receiving correct power. To ensure quality operation, verify proper BNC and power termination, along with proper voltage at camera.
CONNECT CABLES

Default Analog Output: CVBS
Analog Output Selectable: (CVBS I A_HD I G_VI I T_VI) Refer to included “HD ANALOG” page for information on changing signal type.

RVM – Rated Voltage Monitoring

LED COLOR  STATUS
GREEN SOLID RED – BLINK
Safe Power Over 29 Volts (AC24V)
RED – Under 10 Volts (DC12V)

ATTACH CAMERA TO MOUNTING PLATE

Attach the camera to the mounting plate by aligning the hooks on the mounting plate to the tabs on the camera base. Twist the camera base clockwise to lock it in place.
MOUNTING PLATE
TEST MONITOR / OSO CONTROL

To test the camera with a test monitor use either the supplied Test Monitor BNC Lead or optional CE-REMOTE. The Test Monitor BNC Lead plugs into the small, 2 PIN connector (marked CN2) next to the wide 12 wire connection on the circuit board. The CE-REMOTE plugs into the DIN Port. OSD Adjustment can be made by using the OW Joystick or the optional CE-REMOTE. Refer to OSD Manual for detailed instructions on adjusting camera settings.
TEST MONITO

Warning IconNOTICE
The test monitor connection on the CE-REMOTE and the 2-pin connector on the camera board will match the output from the main Analog connector. If the camera is set to an HD Analog option, ensure the test monitor will support that signal type.

CAMERA ANGLE ADJUSTMENT

Adjust the angle of the camera as necessary.

A. Lens Rotation: Rotate the U-Bracket on the gimbal to adjust.
B. Lens Angle: Loosen thumb screws on each side to adjust the tilt of the lens.
C. Camera Plate Rotation: Pinch the gimbal U-Bracket and rotate the camera assembly on the base.
CAMERA ANGLE ADJUSTMENT
ZOOM/FOCUS ADJUSTMENT

Loosen the appropriate adjustment lever by turning counter-clockwise. To widen the viewing angle (zoom the image out), rotate the ZOOM lever to the RIGHT (Counter-clockwise). To narrow the viewing angle (zoom the image in), rotate the ZOOM lever to the LEFT (Clockwise). Adjust the focus near or far as needed by moving the FOCUS lever Left or Right to focus the lens.
ZOOM/FOCUS ADJUSTMENT

After zoom /focus adjustments have been made, tighten the adjustment levers to lock the adjustments. %Lens shown and adjustments may vary depending on camera model.

REPLACE DOME COVER

Carefully replace the dome cover onto the camera assembly by twisting the dome cover clockwise to lock into place. For standard/non-IR cameras with a dome mask, it may be necessary to rotate the clear dome slightly to align the cut out in the mask with the lens.
REPLACE DOME COVER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Clinton Electronics User Manuals

Related Manuals