VIVO STAND-V200T Dual Ultrawide Vertical Monitor Desk Mount Instruction Manual
- June 13, 2024
- Vivo
Table of Contents
Dual Ultrawide Vertical Monitor Desk Mount
Instruction Manual
STAND-V200T Dual Ultrawide Vertical Monitor Desk Mount
SKU: STAND-V200T
https://vivo-
us.com/products/stand-v200t
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v200t
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that
is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly
or inappropriate use.
TIPOVER WARNING
- SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 – Option A – Clamp
Connect Clamp Brace (K) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen
Wrench (T-A).
Remove protective film from Soft Pad (I) and apply to the underside of Clamp
Brace (K). Loosen the screws on the back of Lower Clamp (L) using 4mm Allen
Wrench (T-A), leaving 6mm of thread exposed.
Desk Thickness 0.4” to 2.25” (10mm-58mm)
Hang Lower Clamp (L) into the top 4 slots on Clamp Brace (K). Tighten rear
screws with 4mm Allen Wrench (T-A). Place Clamp Plate (G) on top of the clamp
bolts on Lower Clamp (L).
Desk
Thickness 2” to 3.35” (50mm-85mm)
Hang Lower Clamp (L) into the lower 4 slots on Clamp Brace (K). Tighten rear
screws with 4mm Allen Wrench (T-A). Place Clamp Plate (G) on top of the clamp
bolts on Lower Clamp (L).
Install
to desk and tighten clamp bolt using 6mm Allen Wrench (T-B). Snap Cover (J)
onto the back of assembled base.
STEP 1 – Option B – Grommet
Attach Grommet Plate (H) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen
Wrench (T-A).
Remove protective film from Soft Pad (I) and apply to the underside of Grommet
Plate (H).
Position Base (A)
over grommet hole in desk. If there is no existing grommet hole, drill a
0.375” (10mm) hole through the desktop in the desired mounting position.
Remove a single clamp bolt from Lower Clamp (L) using 6mm Allen Wrench (T-B).
Insert clamp bolt with Clamp Plate (G) through the underside of the desk and
secure to Base (A) using 6mm Allen Wrench (T-B).
STEP 2
Screw Lower Pole (C) into Base (A), and tighten set screws using 4mm Allen
Wrench (T-A). Slide Pole Cable Clip (M) onto Lower Pole (C).
STEP 3
Slide one Arm (B) onto Lower Pole (C) and secure using 6mm Allen Wrench (T-B).
Thread Upper Pole (D) onto Lower Pole (C). Attach Pole Cable Clip (M) to Upper
Pole (D). 
STEP 4
Slide remaining Arm (B) onto Upper Pole (D) and tighten to the pole using 6mm
Allen Wrench (T-B).
Attach Cable Clips (F) to Arms (B).
STEP 5
Install VESA Plate (E) to your monitor using appropriate Screws (M-A, M-B), M5
Washer (M-C) and a Phillips screwdriver. 
STEP 6
Partially install one Wing Nut (S-A) to the top screw on VESA Plate (E) on
monitor and hang over the slot in the top of Arm (B). Install the second Wing
Nut (S-A) to the lower screw on VESA Plate (E).
Adjust as Desired
Adjust the tilt support screws using 4mm Allen Wrench (T-A) and swivel joints
using Wrench (T-C).
Cable Management
Organize cables using Cable Clips (F), Pole Cable Clips (M), and Cover
(J).
Love your new VIVO
setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 04/12/2023
REV1 Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Dual Ultrawide Vertical Monitor Desk Mount with Arms – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>