GOLDEN LIGHTING 3308-LP BLK-WTG Kepler 4 Light 39 Wide Linear Pendant Instruction Manual
- June 13, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3308-LP BLK-WTG Kepler 4 Light 39 Wide Linear Pendant
Instruction Manual
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Mounting strap (B) contains several threaded holes. Two
sets of mounting screws (A & D) should be attached to mounting strap
(B). You may need to tighten nuts (C) which hold mounting screws
(A) in place. If the screws are not attached, please hold canopy (F)
up to mounting strap ( B ). Line up the holes in canopy (F) with the
holes in mounting strap (B) and insert mounting screws (A) into
mounting strap (B) so that mounting screws (A) protrude through the
holes in canopy (F). Mounting screws (A) are long, please test the
canopy against the mounting strap to see how far you should insert the screws.
Tighten nuts (C) onto mounting screws (A) to hold the screws in place.
2. Pull the house wires through the center of mounting strap (B). Place
mounting strap (B) over the junction box so that mounting screws (A)
are in alignment with the hole locations on the fixture’s canopy (F).
Secure mounting strap (B) to the junction box with mounting screws (D)
and a screwdriver. Tighten the screws securely
ASSEMBLING THE FIXTURE
Measure to determine the correct number of rods (L) needed for proper
hanging height. There are three 12-inch rods and one 6-inch rod included for
each side of the fixture. To shorten the fixture, slide the desired number of
excess rods off. To lengthen the fixture, add additional rods. If additional
rods are needed, please contact the place of purchase to order more. Feed the
fixture wires from posts (I) into rods (H). Pull the wires until taut.
4. Thread the rods together to secure. Secure rods onto the fixture frame by
twisting the bottom of the rods onto post (I). Twist the top of the rods
into the threads of swivel posts (O). Pull the fixture’s wires through
swivel (O) and canopy (F). Trim the wires to the desired length adding
at least 8 to 10 inches of wire. 5. Attach swivel posts (O) to the canopy
(F) by placing the plate (P) inside canopy (F). Twist on washers
(Q) and hex nuts (R) to secure the plate (P) to the canopy and to
the top threads of swivels posts (O).
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting
strap and wrap the fixture’s ground wire around the ground screw. Use a
screwdriver to tighten the top of ground screw (E) onto the wires and into
the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (F) up to the ceiling so that mounting screws (A) protrude
through the holes in canopy (F). Tightly thread deco nuts (P) onto the
exposed threads of mounting screws (A). 8. Thread metal shades (L)
through bottom of glass shades (K). Lift metal shades (K) up to
sockets (J). Secure metal shades (K) to sockets (J) using socket
rings (M). Install light bulbs (not provided) in accordance with the
fixture’s specifications. Do not exceed the maximum recommended wattage. Your
installation is complete. Turn on the power and test the fixture.
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>