MiBOXER FUT100 RGB and CCT Lamp Instruction Manual

MiBOXER FUT100 RGB and CCT Lamp

Product Information

The Subordinate New Brand RGB+CCT lamp is a smart lighting device that uses Zigbee 3.0 and 2.4G wireless transmission technology. It features low power consumption, automatic network building capability, and anti-interference. With the MiBoxer Zigbee gateway, users can enjoy wireless dimming, color control, remote control, group control, and music rhythm functions. The lamp supports a 2.4G RF remote control and follows the Zigbee 3.0 standard protocol. It offers 16 million colors to choose from and adjustable color temperature. Users can also dim the brightness and saturation of the light.

Product Usage Instructions

Linking Code Instructions

1. Power off the lamp and wait for 10 seconds.
2. Press the Link/Unlink button on the remote control three times within 3 seconds.
3. The lights on the lamp will blink slowly for 3 times, indicating successful linking.
4. If the lights are not blinking slowly, the linking process has failed. Please repeat the above steps. Note: Once a light is linked, it cannot be linked again.

Unlinking Code Instructions

1. Power off the lamp and wait for 10 seconds.
2. Press the Link/Unlink button on the remote control five times within 3 seconds.
3. The lights on the lamp will blink quickly for 10 times, indicating successful unlinking.
4. If the lights are not blinking quickly, the unlinking process has failed. Please repeat the above steps. Note: Lights that haven’t been linked do not need to be unlinked.

Compatible 2.4G RF Remote Controls
The Subordinate New Brand RGB+CCT lamp is compatible with the following 2.4G RF remote controls (purchased separately):

• FUT100
• FUT089S
• FUT089
• FUT089-B
• FUT088
• FUT092
• FUT092-B
• FUT096
• FUT096-B
• B8
• B0 / B0-B
• B3 / B3-B / T3
• B4 / B4-B / T4
• S2-B / S2-W S2-G
• SET 8.8.8.8+
• FUTD01

Dynamic Mode Table Selection (only for remote control)
To select a dynamic mode from the table, follow these steps:

1. Make sure the light is in static mode.
2. Press the S+ button on the remote control five times quickly until the blue light flashes slowly for 3 times, indicating successful activation of dynamic mode table 1.
3. To activate dynamic mode table 2, press the S- button on the remote control five times quickly until the yellow light flashes slowly for 3 times.

Dynamic Mode Table 1 (default)

Dynamic Mode Table 2 (manually switched)

Product features

Made by new Zigbee 3.0 wireless transforming technology with low power consumption, strong ability to build network automatically and an- interference. with MiBoxer Zigbee gateway to get wireless dimming color, remote control, timing control, group control, and music rhythm functions. Support 2.4G RF remote control.

• 16 Millions of colors to choose
• Color temperature adjustable
• Dim brightness / Saturation
• Follow Zigbee 3.0 standard protocol
• Support Zigbee 3.0 remote control (Zigbee 3.0 gateway is needed)
• Support 2.4G Remote control
• Auto-transmuting & Synchronization
• Support Smartphone app control (Zigbee 3.0 gateway is needed)
• Support third-party voice control (Zigbee 3.0 gateway is needed)
• DMX512 controllable (Only for RGB+CCT output mode DMX512 LED transmitter is needed)

Various control solutions:

2.4G RF Remote control instruction

Linking Code Instructions

1. Power off and power on again are 10 seconds.
2. Short press the ” I ” button 3 times within 3 seconds
3. Lights blink 3 times slowly means linking is done successfully

Linking fails if the light is not blinking slowly, Please follow the above steps again. (Note: Light that has linked can’t link again)

unlinking Code Instructions

1. Power off and power on again after 10 seconds.
2. Short press the ” I “button 5 times within 3 seconds.
3. Lights blink 10 times quickly means unlinking is done successfully.

Unlinking fails if the light is not blinking quickly, Please follow the above steps again. (Note: Light hasn’t linked that doesn’t need to unlink)

compatible with these 2.4G RF remote controls (Purchased separately)

Dynamic mode table selection (only for remote control

1. Select dynamic mode table 1:
   While the light is in static mode, short press the ” S+ ” button 5 times quickly until the blue light flashes 3 times slowly, and static mode is activated successfully.

2. Select dynamic mode table 2:
   While the light is in static mode, short press the” S- ” button 5 times quickly until the yellow light flashes 3 times slowly, and static mode is activated successfully.

Dynamic mode table 1 (default)

Adjustable

2| Automatic color change
3| Sam
4| Gemstone
5| Twilight
6| American
7| Fat Tuesday
8| Party
9| Slow Color Splash

Dynamic mode table 2 (need to switch manually)

Adjustable

2| White light Gradual change
3| RGB gradual change
4| Seven colors jump to change
5| Jump to change randomly
6| Red light gradual change

+Flash 3 times

7| Green light gradual change

+Flash 3 times

8| Blue light gradual change

+Flash 3 times

9| White light gradual change

+Flash 3 times

Auto transmitting and synchronization (only for remote control)

• Remote signal auto-transmitting
  One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.

• Dynamic modes auto synchronization
  Multi lights can synchronize if they are in the same dynamic mode and linked with the same remote (the distance between each light is within 30m)

. “Do Not Disturb” mode is activated and shut down (default activated)
Turn on “Do Not Disturb” mode (wide use in the area which has power failure frequently to save energy)

2.4G RF Remote turn on and turn off instruction
Turn on “Do Not Disturb” mode: Press the “OFF” button three times within three seconds and press the “ON” button three times, Activated successfully once the LED light flashes four times quickly.
Attention : Do not disturb mode is activated

1. When the light is OFF status (For example: Use app or remote to turn off light) The light is OFF status once you turn off the power and turn it on again. (User must turn off and turn on power twice times to activate light or use APP / remote to activate light)
2. When the light is ON status The light is ON status once you turn off and turn on power one time.

Turn off “Do Not Disturb” mode: Press the “ON” button three times within three seconds and press the “OFF” button three times, closed successfully once the led light flashes four times slowly.

• Attention : The light will be always on “ON” status if you turn on and turn off the power once the user closes “Do Not Disturb” mode.

App turns on and off “Do Not Disturb” mode instruction check details

Smartphone APP control instruction

Added Zigbee 3.0 gateway into “Tuya Smart” App (please review instructions for Zigbee 3.0 gateway)

1. Connect with power supply.
2. Pairing network (attention: factory default is pairing network). Way one: Turn off and turn on light 3 times or over 3 times continuously, the light is in breathing status. Way two: Long press the ” SET ” key until the indicator light flashes.
3. Open the “Tuya Smart” APP to click Zigbee gateway, then click “Add sub device”.
4. Click “Indicator is flashing quickly”.
5. Support APP dimming or group control etc. once added successfully.

App turns on and off “Do Not Disturb” mode (default activated)
Click the light that need to be set up or group control click “More” and click “Power-on behavior” Turn on or off

Philips Hue control instruction

Added “Philips Hue” into the APP

1. Connect with the power supply
2. Pairing network (attention: factory default is pairing network) Way one: Turn off and turn on the light 3 times or over 3 times continuously, the light is in breathing status. Way two: Long press the ” SET ” key until the indicator light flashes.
3. Open “Philips Hue” App to click “SETTINGS” and click “Lights”
4. Click “+” on the top of the right corner
5. Click “Search”
6. Click “Start configuration”, Follow the app instructions to complete the configuration

Alexa voice control instruction

Alexa control (Audio support Zigbee 3.0 protocol)
You can connect directly if your Amazon ECHO already is built-in Zigbee 3.0 protocol, following the model with Zigbee 3.0 protocol:
Amazon ECHO Plus ( 2nd Cen), ECHO (4th Cen), ECHO Studio, ECHO Show (2. Gen)

1. Connect with the power supply
2. Pairing network (attention: factory default is pairing network) Way one: Turn off and turn on the light 3 times or over 3 times continuously, the light is in breathing status. Way two: Long press the ” SET ” key until the indicator light flashes.
3. Say to Amazon ECHO “Alexa, Discover devices” Wait for a while to discover the device, Voice control is activated

Alexa control (Audio doesn’t support Zigbee 3.0 protocol)
Please add device to Miboxer Zigbee 3.0 gateway if your Alexa doesn’t support ZigBee 3.0 protocol (check details in page 7), then start following the steps

1. Open Alexa App
2. Click “More” at the bottom of the right corner
3. Click “Skills & Games”
4. Click “Q” on the top of the right corner
5. Type into “Smart life” and search
6. Click the “Smart Life” skill, follow the instructions to finish the configuration, and start the voice control

Google Home voice control instruction

Please add device to the MiBoxer Zigbee 3.0 gateway (check details on page 7) and start following the steps

1.  Open Google Home App
2. Click “+” on the top of left corner
3. Click “Set up device”
4. Click “Works with Google”
5. Click “Q” on the top of the right corner
6. Type into “Smart life” and search
7. Click the “Smart Life” skill, follow the instructions to finish the configuration, and start the voice control

DMX512 LED Transmitter Control

(Purchased separately)

DMX512 LED Transmitter Link/Unlink

1. Follow the instructions of the DMXS12 transmitter (FUTDOI), Choose the zone for the light by pressing (e.g. “CH 12” means zone 12)
2. Link Power off and power on again after 10 seconds.
3. When the light is on, short press “O” 3 times within 3 seconds
4. The light blinks slowly 3 times, which means the linking is done successfully

Unlink

• Power off and power on again after 10 seconds.
• When the light is on, short press “O” 5 times within 3 seconds
• The light blinks quickly 10 times, which means the unlinking is done successfully

If the link or unlink failed, please follow the above steps again.

Attention

1. Please turn off the power supply before installation.
2. Please ensure the input voltage to be same as the requirements from the device.
3. Don’t disassemble the device if you are not an expert, otherwise, it will damage it.
4. Please do not use the light in a place with a wide range of metal areas or strong electromagnetic waves nearby, otherwise, the remote distance will be seriously affected.

Scan the QR code to watch the Zigbee series video instructions Or enter into following link directly
https://miboxer.com/light/video/zigbee.html

References

• Zigbee Series Video - MiBoxer
• Zigbee Series Video - MiBoxer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>