GE Lighting Cync Outdoor Dynamic Effects Light Strip and Extension Installation Guide

GE Lighting Cync Outdoor Dynamic Effects Light Strip and Extension

What’s Included

(Devices each sold separately) ****

Light Strip Contents

16 ti. Full Color Light Strip

• 16 ft. Full Color Light Strip
• Power supply with plug
• (15) Mounting clips
• (15) Mounting screws
• (l) End cap and glue

32 ft. Full Color Light Strip

• 32 ft Full Color Light Strip
• Power supply with plug
• (30) Mounting clips
• (30) Mounting screws
• (l) End cap and glue

Light Strip Extension Contents

Light Strip Extension

• 8 ft. Full Color Light Strip
• (8) Mounting clips
• (8) Mounling screws

What You’ll Need

1. Drill with l/16″ drill bit
2. Screwdriver
3. Tape measure
4. Scissors

SET UP

Set up your Light Strips with three easy steps

1. STEP 1
   Connect to the Cync App, powered by Savant

2. STEP 2
   Trim to desired length

3. STEP 3
   Prep surface and install

SET UP in the CYNC APP

1. STEP 1
   Plug in and power on your Light Strip by pressing the On/Off button on the power supply.

2. STEP 2
   Download the Cync App, powered by Savant, on your smartphone.

3. STEP 3
   Add your smart lights to the Cync App, then connect to Hey Google or Amazon Alexa voice assistants (sold separately) in the Cync App.

For set up help, visit cyncsupport.gelighting.com or call 1-8lili-302-29li3
GE and C by GE are trademarks of General Electric Campany. Used under trademark license. Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Google and other relaled marks and logos are trademarks of Google LLC.

MESURE & TRIM TO SIZE

1. STEP 1
   Measure where you’re planning to install your lights. If your space requires Light Strip Extensions, make sure to attach them before trimming your strips.

2. STEP 2
   With your Light Strip unplugged, cut where the trim points (faint gray hash marks) are indicated.
   A Make sure the strip is not plugged in at the wall when cutting.
   NOTE: Cutting anywhere else will permanently damage the strip.

3. STEP 3
   Using the end cap and adhesive, put a bead of glue around the inside edge of the end cap and insert on the end of the Light Strip. Let dry for 30 minutes.

STRIP BENDING OPTION

INSTALL YOUR STRIP

1. STEP 1
   Locate the starting point to install your Light Strip. Install the first clip by drilling a 1/16-inch hole and screwing in the provided screw. The open ends of the clip should follow the desired direction of your strip.

2. STEP 2
   Install mounting clips every 13 inches until you reach the end of your Light Strip.

3. STEP 3
   Mount the Light Strip into the clips by snapping the Light Strip into each clip. To reposition the strip, unsnap the Light Strip and reinstall the mounting clip in the desired location.
   NOTE: The mounting clips/screws will damage walls.

4. STEP 4
   Connect the adapter to a waterproof outlet box and turn on the lights to complete setup.

Extend Strip & Manually Enable Light Shows

• STEP 1
  Unplug the power supply Screw on the waterproof connector to attach the extension to the Light Strip.
  NOTE : 16 ft. Outdoor Strip can be extended up to 32 ft total. 32 ft. Outdoor Strip can be ethxete nLidgehdt Sutpri pt,o a Mpp lfyt. gtolutea l. aInf dn oint setaxltl etnhdei ng end cap for waterproof protection.

• STEP 2
  Unplug, then plug your strip back in to detect its new length. This is important for Light Effects.

ENABLE LIGHT EFFECTS
Cycle through light show by pressing the Light Effect button

FCC Statement

• STEP 1
  Measure where you’re planning to install your lights. If your space requires Light Strip Extensions, make sure to attach them before trimming your strips.

• STEP 2
  With your Light Strip unplugged, cut where the trim points (faint gray hash marks) are indicated.
  A Make sure the strip is not plugged in at the wall when cutting.
  NOTE : Cutting anywhere else will permanently damage the strip.

• STEP 3
  Using the end cap and adhesive, put a bead of glue around the inside edge of the end cap and insert on the end of the Light Strip. Let dry for 30 minutes.

Warning : Changes or modifications to lhis unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment hos been tested and found to comply with the limits for a Closs B digital device, pursuant to Port 15 of the FCC Rules. These limits ore designed to provide reasonable protection against harmful Interference In o residential installation. This equipment generates, uses, and con radiates radio frequency energy ond, if not installed ond used in accordance with the instructions, moy cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct lhe interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect lhe equipment into an oullet on o circuit different from lhat to which lhe receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

The device must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Port 15 of the FCC Rules. Operation Is subject to the following two conditions:
(1) this device moy not cause harmful interference, ond (2) this device must accept ony interference received, Including Interference that may cause undesired operation.
FCC RF Radiolion Exposure Statement Caution, To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

IC Statement

This device complies with RSS2L,7 of Industry Canada. Cet oppareil se conforme a RSS2L,7 de Canada This device complies with Industry Canada license-exempt RSS standord(s). Operation is subject to the following two conditions,
(1) this device moy not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Appareils radio exempts de licence.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must be installed to provide o separation distance of at least 20cm from all persons and must not be collocated or operating In conjunction with any other antenna or transmitter.

Like your new Outdoor Dynamic Effects
Light Strip or Extension?
Share your creations!
See the possibilities at gelighting.com/cync

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>