ESR 6B012A REBOUND Series Rebound Magnetic Keyboard Case User Manual
- June 13, 2024
- ESR
Table of Contents
ESR 6B012A REBOUND Series Rebound Magnetic Keyboard Case User Manual
Button Descriptions
Power On/Off
Long press button for 2 seconds to turn keyboard on or off.
Pairing Mode
Long press + for 3 seconds to enter pairing mode. Bluetooth status will flash to indicate that keyboard has entered pairing mode. If not connected after 2 minutes, pairing mode will turn off.
Auto Reconnect
When turned on, keyboard will automatically reconnect with last paired device within 5 seconds.
Power Light Overview
Charging:
Fully charged:
Low battery:
Standby Mode
Keyboard backlight will turn off automatically after 90 seconds of inactivity.
After 10 minutes of inactivity, keyboard will enter standby mode. When in
standby mode, press any key to wake keyboard
Backlight
Press + to select backlight brightness level (high, medium, low, off).
Press + to select backlight color (12 colors).
Factory Reset
Long press + + for 3 seconds until charging status and Bluetooth status lights flash 3 times, indicating successful factory reset
Shortcut Keys
Troubleshooting Guide
If the keyboard stops working, please check the following:
- Keyboard is turned on. If not, Long press on/off button for 2 seconds to turn keyboard on.
- Keyboard has sufficient battery (at least 20%). If not, fully charge it using included USB-A to USB-C cable.
- Bluetooth connection to your iPad is stable. Turn keyboard off, wait 10 seconds, and then turn back on again.
If problem persists, unpair keyboard by going to Settings > Bluetooth > Device List > “ESR Keyboard” and tap , then choose “Forget This Device”. Follow Bluetooth pairing instructions to reconnect your keyboard.
If keyboard remains unresponsive, repeat above steps. If you are still experiencing problems, contact our customer service team at.
Reminder
This Bluetooth keyboard has a rechargeable battery. When not using keyboard
for an extended period of time, turn it off using the on/off button to prolong
battery life.
FCC ID：2APEW- 6B012A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC：24790- 6B012A
This device complies with Industry Canada licence-exempt RSS standard( s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device.”
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp.
hereby declares that this product 6B012A is in compliance with the essential
requirements and other relevant provisions of Directive
2014/53/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 6B012A
is available from www.esrgear.com
This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>