HOT WHeeLs GVK49 Radio Control Mattel Car Instructions

: June 9, 2024
: HOT WHEELS

Table of Contents

ASSEMBLY INSTRUCTION
CONTENTS/ FEATURES
BATTERY INSTALLATION
OPERATION
QUICK TIPS
CONSUMER INFORMATION
SAFETY TIPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HOT WHeeLs GVK49 Radio Control Mattel Car Instructions

CAUTION: Surfaces may become hot and cause burns if electronics get wet. Do not operate vehicle through water or snow.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION

ASSEMBLY INSTRUCTION

This set includes: 1 vehicle

PRODUCT OVERVIEW

FORWARD

REVERSE

FORWARD LEFT OR RIGHT

REVERSE LEFT OR RIGHT

©2022 Mattel. ® and ™ designate
U.S. trademarks of Mattel, except as noted. ®

ASSEMBLY INSTRUCTION

CONTENTS/ FEATURES

Forward / Reverse
Left / Right
Battery cover
ON(I) / OFF(O)
Steering adjuster – Adjust, if necessary, to keep vehicle running straight
Antenna tube

A. Insert flexible antenna wire through antenna tube, then insert end of tube firmly into transmitter hole

B. Tie a knot at the end of the flexible antenna wire to keep the tube in place.

Do not insert wire into sockets.

BATTERY INSTALLATION

(Transmitter & Vehicle)

Requires 4 AA (LR6) 1.5V alkaline batteries for the vehicle and 2 AA (LR6) 1.5V alkaline batteries for the transmitter. Batteries not included.

Vehicle

Unscrew the battery cover with a Philips head screwdriver (not included).
Vehicle requires 4 AA (LR6) 1.5V alkaline batteries. Install with polarity (+/-) as shown inside the battery compartment.
Replace battery cover and tighten screw.

Transmitter

Remove the battery cover.
Transmitter requires 2 AA (LR6) 1.5V alkaline batteries. Install with polarity (+/-) as shown inside the battery compartment.
Replace battery cover and push shut.

NOTE: Once the batteries are installed, the transmitter will always be “ON” and will work automatically the moment you use it.

OPERATION

FORWARD
REVERSE
FORWARD LEFT OR RIGHT
REVERSE LEFT OR RIGHT

QUICK TIPS

When the vehicle starts to lose power, it may lose functionality or performance. It’s time for fresh batteries. The vehicle’s running time may change depending on your driving style.
Radio interference can affect the vehicle’s performance. Interference can be caused by other R/C vehicles running on the same frequency, electrical wires, large buildings or CB radios. Try to stay away from these!
Point the transmitter up – not down toward the vehicle. If the vehicle gets too far away, it won’t work properly.
Don’t drive the vehicle in sand or through water or snow. If the vehicle does get wet, wipe it with a towel and allow to dry completely overnight.
Don’t store the vehicle near heat or in direct sunlight. Always turn the vehicle’s power OFF and remove all batteries for storage.
If the vehicle malfunctions, turn the vehicle’s power OFF and ON again. If the transmitter malfunctions, remove and reinstall all batteries in the transmitter. These should reset the vehicle and transmitter and let you resume normal operation.

CONSUMER INFORMATION

Note to Adults: To ensure that the child’s play is both safe and fun, please review all operating instructions and safety rules with your child.

SAFETY TIPS

NEVER drive your vehicle on streets! They’re for real cars!
DO NOT pick up the vehicle while in motion.
Keep fingers, hair and loose clothing away from the tires and the wheel hubs while the vehicle is switched ON.
Adult supervision is recommended when this vehicle is being operated.
To avoid accidental operation, remove all batteries when not in use.

Battery Performance Note:

For best performance use regular or high-performance alkaline batteries (where disposable batteries are called for). If your vehicle is supplied with standard (carbon-zinc) batteries for initial use and/or demonstration purposes, we recommend replacing them with alkaline batteries when necessary. Battery life may vary depending on battery brand.

FOR PRODUCT SOLD IN USA

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

FOR PRODUCT SOLD IN CANADA

This equipment complies with FCC & Canada radiation exposure limits set forth for uncontrolled environments.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.