MEAN WELL HBG-100P Series Constant Current LED Driver User Guide

MEAN WELL HBG-100P Series Constant Current LED Driver User Guide?

Features

• Constant Current mode output
• Circular shape PCB type design
• Built-in active PFC function
• Function options: output adjustable via potentiometer; 3 in 1 dimming; DALI
• Typical lifetime>50000 hours
• 5 years warranty

Applications

• LED bay lighting
• LED down lighting
• LED spot lighting
• LED mining lighting
• LED stage lighting

Description
HBG-100P seriesis a 100W AC/DC PCB type LED driver featuring the circular shape design.  It operates from 90~305VAC and offers constant current output models with different ratedvoltage ranging between 36V and 60V. Thanks to the high efficiency up to 91.5%, with thefanless design, the entire series is able to operate for -40°C ~ +45°C under free air convection. HBG-100P is equipped with various function options, such as dimming methodology, so as to provide the optimal design flexibility for LED lighting system.

Model Encoding

SPECIFICATION

60V
OPEN CIRCUIT VOLTAGE (max.)| 37V| 49V| 62V
CURRENT ADJ. RANGE| Adjustable for A-Type only (via built-in potentiometer)
1.62 ~ 2.7A| 1.2 ~ 2A| 1.0 ~ 1.6A
CURRENT RIPPLE| 5.0% max. @rated current
CURRENT TOLERANCE| ±5.0%
SET UP TIME Note.4| 2000ms / 115VAC            500ms / 230VAC
**INPUT| VOLTAGE RANGE Note.3| 90 ~ 305VAC             127 ~ 431VDC(Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE| 47 ~ 63Hz
POWER FACTOR| PF≧0.96/115VAC, PF≧0.96/230VAC, PF≧0.94/277VAC@full load(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
TOTAL HARMONIC DISTORTION| THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC)(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY (Typ.) Note.5| 91%| 91%| 91.5%
AC CURRENT| 1.1A / 115VAC| 0.5A / 230VAC| 0.45A / 277VAC|
INRUSH CURRENT(Typ.)| COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER| 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| <0.75mA / 277VAC
NO LOAD / STANDBY POWER CONSUMPTION| Standby power consumption <0.5W for B/DA-Type A-Type please refer to Note. 7
****PROTECTION| OVER CURRENT| 95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
OVER VOLTAGE| 41 ~ 49V| 54 ~ 63V| 65 ~ 75V
Shut down o/p voltage, re-power on to recovery
OVER TEMPERATURE Note.11| Shut down o/p voltage, re-power on to recovery
****ENVIRONMENT| WORKING TEMP.| Ta=-40 ~ +45℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
WORKING HUMIDITY| 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 45℃)
VIBRATION| 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
****SAFETY & **EMC| SAFETY STANDARDS| UL8750,CSA C22.2 No.250.13-12; ENEC BS EN/EN61347-1,BS EN/EN61347-2-13,BS EN/EN62384, GB19510.1, GB19510.14,EAC TP TC 004 approved
DALI STANDARDS| Compliance to IEC62386-101, 102, 207 for DA-Type only
WITHSTAND VOLTAGE| I/P-O/P:3.75KVAC| I/P-FG:2KVAC| O/P-FG:0.5KVAC|
ISOLATION RESISTANCE| I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load ≧60%) ; BS EN/EN61000-3-3, GB17743, GB17625.1,EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547,light industry level(surge immunity:Line-Earth:4KV, Line- Line:2KV),EAC TP TC 020
**OTHERS| MTBF| 346.8Khrs min.         MIL-HDBK-217F (25℃)
DIMENSION| Refer to mechanical specification
PACKING| 0.3Kg; 45pcs/14.5Kg/1.60CUFT
NOTE**|

1.  All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2.  Please refer to “DRlVlNG METHODS OF LED MODULE”.
3. De-rating may be needed under low input voltages. Please refer to Static Characterless sections for details.
4. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
5. The DA type power supply is less efficient than the typical efficiency in specification by 1%
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains
8. This series meets the typical life expectancy of >50,000 hours of operation when Ta is about 45℃ or less.
9. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com
10. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
11.  All functional testing must be filled with potting,including OTP function .※ Product Liability Disclaimer：For detailed information, please refer to https://[www.meanwell.com/serviceDisclaimer.aspx](http://www.meanwell.com/serviceDisclaimer.aspx)

BLOCK DIAGRAM

DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.

Typical output current normalized by rated current (%)

Typical output current normalized by rated current (%)

3in 1 dimming function (for B-Type)

•  Output constant currentlevel can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1~10VDC, or 10V PWM signal or resistance.
• Direct connecting to LEDs is suggested. Itis not suitable to be used with additional drivers.
• Dimming source current from power supply: 1004A (typ.)

pplying additive 1~ 10VDC
pplying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):

**Applying additive resistance:

Note:** In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.

Using a switch and relay can turn ON/OFF the lighting fixture.

DALI Interface (primary side; for DA-Type) –

• Apply DALIsignal between DA+ and DA-.
• DALI protocol comprises 16 groups and 64 addresses.
• Firststeps fixed at 8% of output. 
  

OUTPUT LOAD vs TEMPERATURE

AMBIENT TEMPERATURE, Ta (C)

STATIC CHARACTERISTIC

INPUT VOLTAGE (V) 60Hz 

**POWER FACTOR (PF) CHARACTERISTIC

**

TOTAL HARMONIC DISTORTION (THD)

EFFICIENCY vs LOAD
HBG-100P series possess superior working efficiency that up to 91.5% can be reached in field applications. X 60V Model

LOAD

MECHANICAL SPECIFICATION

Atype

BIDAtype

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>