AMERICAN LIGHTING 2430-878 Winsley 5 Wide Vantage Mini Pendant Instruction Manual

AMERICAN LIGHTING 2430-878 Winsley 5 Wide Vantage Mini Pendant

Product Information

• Product Name: 2430-84/878
• Date of Manufacture: New. 08/27/2021

Product Usage Instructions

Installation:

• Shut off power at the fuse box or circuit breaker before installation.
• Remove the old fixture and its mounting hardware.
• Carefully unpack the new fixture and lay out all theparts.

Connecting the Wires:

• Connect the electrical wires as shown in Fig.2.
• Ensure that all wire connectors (C) are secured.
• If your junction box has a ground wire (green or bare copper),connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (G) using thegreen screw provided.
• Tuck wire connectors neatly into the junction box.

Finishing the Installation:

• Place the canopy (J) onto screws (B) and secure with finials (A).
• Unscrew metal ring (F) and place glass shade (I) onto socket cup (H).
• Secure glass shade (I) with metal ring (F).
• Install (1) one medium base (E26) bulb up to 60 watts each orCFL or LED equivalent (not included) in accordance with the fixturespecification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
• Your installation is now complete. Return power to the junction box and test the fixture.

Note: The illustration in Fig.1 is for installation purposes only and may or may not be identical to the fixture purchased.

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.

3. Thread screws (B) into pre-drilled holes in circular strap (G) spaced same distance apart as holes in canopy (J) andtighten with nuts (E). The length of screws (B) may be adjusted if necessary.

4. Attach circular strap (G) to junction box (not included) using mounting screws (D). The side of circular strap marked “GND”must face out.

5. Determine desired hanging height and thread rods (M2, and M1) to all thread of fixture’s body. Screw loop (K1) onto rod (M1). Pass wires carefully through each rod as you assemble.

6. Attach quick link (L) to loop (K1) and loop (K2) on canopy (J). Carefully feed wires through loop (K1), quick link (L),and loop (K2).
   CONNECTING THE WIRES (Fig.2)

7. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’sground wire directly to the circular strap (G) using thegreen screw provided.

8. Tuck wire connectors neatly into the junction box.
   FINISHING THE INSTALLATION (Fig.1)

9. Place canopy (J) onto screws (B) and secure with finials(A).

10. Unscrew metal ring (F) and place glass shade (I) onto socket cup (H). Secure glass shade (I) with metal ring (F).

11. Install (1) one medium base (E26) bulb up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM

WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the junction box and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not beidentical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>