minka 4046-84 Acacia 6 Light 30 Wide Vantage Chandelier Instructions

minka 4046-84 Acacia 6 Light 30 Wide Vantage Chandelier

Product Information

The product is item#4046-84, a lighting fixture. It is designed for installation in residential or commercial spaces. The fixture requires electrical power to function and can accommodate up to six medium base (E26) bulbs with a maximum wattage of 60 watts each. The fixture comes with a mounting plate, ground screw, mounting screws, glass shade, and metal rings.

Product Usage Instructions

1. Before starting the installation, ensure that the power is shut off at the fuse or circuit breaker.
2. Connect the electrical wires according to the provided diagram (Fig.3). Make sure all wire connectors are secured. If your outlet box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided.
3. Tuck the wire connections neatly inside the outlet box.
4. Proceed to finish the installation by following the steps below:
   • Thread the fixture screws through the canopy and into themounting plate. Secure them in place.
   • Place the glass shade over the socket cups and secure it using the metal rings.
   • Install up to six medium base (E26) bulbs, or CFL or LED equivalents, with a maximum wattage of 60 watts each. Make sure to adhere to the fixture’s specification and not exceed the maximum wattage rating.
5. Your installation is now complete. Restore power and test the fixture to ensure proper functionality.

WARNING:  SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

Installation Instructions

READ AND SAVE THESE INSTRUCTIONS

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker and remove the old fixture included the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.
3. Adjust position of each lamp arm. (As shown in Fig.2)
4. Place mounting plate (B) over outlet box (A) (Not included) and align mounting slots with mounting holes of outlet box (A). Feed mounting screws (C) through mounting slots of mounting plate (B) and mounting holes of outlet box (A). Make sure the side of the mounting plate (B) marked “GND” must face out.
5. Determine desired hanging height and thread rods (I1 and I2) to the all thread of the fixture body. Screw loop (H1) onto rod (I1). Pass wires carefully through each rod as you assemble.
6. Attach quick link (G) to loop (H1) and loop (H2) on canopy (E). Carefully feed wire through loop (H1), quick link (G), and loop (H2).
   • CONNECTING THE WIRES (Fig.3)
7. Connect the electrical wires as shown in Fig.3, making sure that all wire connectors (D) are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.
8. Tuck wire connections neatly inside the outlet box (A).
   • FINISHING THE INSTALLATION (Fig.1)
9. Thread fixture screws (F) through canopy (E) and into mounting plate (B) and secure.
10. Place glass shade (K) over socket cups (J). Secure glass shade (K) using metal rings (L).
11. Install (6) six medium base (E26) bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>