AMERICAN LIGHTING 2433-84 Winsley 3 Light 22 Wide Vantage Bathroom Vanity Light Instructions

AMERICAN LIGHTING 2433-84 Winsley 3 Light 22 Wide Vantage Bathroom Vanity

Light

Product Information

Product Usage Instructions

1. Before starting the installation, ensure that the power is shut off at the fuse box or circuit breaker.
2. Remove the old fixture, including the mounting hardware.
3. Carefully unpack the new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary forinstallation.
4. Thread the mounting screws (B) into the pre-drilled holes inthe circular strap (G), spaced the same distance apart as the holesin the back plate. Tighten them with nuts (E). Adjust the length of the mounting screws if necessary.Attach the circular strap (G) to a junction box (not included) using junction box screws (D). Ensure that the side of the circular strap marked “GND” faces out.
5. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directlyto the circular strap (G) using the green screw provided. Tuck wire connectors neatly into the junction box.
6. Place the back plate onto the mounting screws (B) and secure it with finials (A).
7. Unscrew the metal ring (F) and place the glass shade (I) ontothe socket cup (H). Secure the glass shade (I) with the metal ring (F).
8. Install up to four medium base (E26) bulbs, each up to 60 watts or CFL or LED equivalent (not included), following the fixture’sspecification. Do not exceed the maximum wattage rating.
9. Your installation is now complete. Return power to the junctionbox and test the fixture.

Note: The illustration in this manual (Fig.1) is for installation purposes only. It may or may not be identical to the fixture purchased.

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small partsnecessary for installation.

3. Thread mounting screws (B) into pre-drilled holes in circular strap (G) spaced same distance apart as holes in back plate and tighten with nuts (E). The length of mounting screws (B) may be adjusted if necessary.

4. Attach circular strap (G) to junction box (not included) using junction box screws (D). The side of circular strap marked “GND” must face out.
   CONNECTING THE WIRES (Fig.2)

5. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’sground wire directly to the circular strap (G) usingthegreen screw provided.

6. Tuck wire connectors neatly into the junction box.
   FINISHING THE INSTALLATION (Fig.1)

7. Place back plate onto mounting screws (B) and secure with finials (A).

8. Unscrew metal ring (F) and place glass shade (I) onto socket cup (H). Secure glass shade (I) with metal ring (F).

9. Install (4) four medium base (E26) bulb up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not beidentical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>