deerma DEM-F800 Humidifier Instructions
- June 13, 2024
- deerma
Table of Contents
deerma DEM-F800 Humidifier
Product Information
The Deerma Humidifier is designed to keep your life clean and refreshing. With its micron mist and simple operation, it deeply moisturizes your skin and each corner of your house. This humidifier creates a comfortable environment by atomizing water into ultrafine particles and diffusing water mist into the air through a pneumatic device. It can maintain ideal humidity levels in your bedroom and prevent the generation of static electricity.
Product Structure
- Mist nozzle
- Water tank
- Water gauge
- Water tank port
- Knob
- Decorative ring
- Base air inlet
- Base
- Power cord
- Air outlet
- Silicone box
- Float
- Float gland
Product Parameters
- Product name: Humidifier
- Rated voltage: 220-240V
- Capacity: 5L
- Product size: 219201304mm
- Product model: DEM-F800
- Rated frequency: 50-60Hz
- Rated power: 25W
Operating Principle
The Deerma humidifier uses ultrasonic waves to atomize water into ultrafine
particles. The 1.7 million high-frequency oscillations per second generated by
the ultrasonic wave diffuse water mist into the air through the pneumatic
device, achieving uniform air humidification. It helps maintain ideal humidity
levels in your bedroom and prevents the generation of static electricity.
Product Usage Instructions
- Lift the water tank out.
- Press the button to open the water gland outward.
- Fill water into the water tank, controlling the amount according to demand.
- Press the water gland down until it clicks.
- Install the water tank filled with water onto the machine body.
- Plug in the machine and turn the knob switch.
Cleaning and Maintenance
If there is no mist after power-on:
- Cause: Check whether the bottom air inlet screen is blocked or if there is a large amount of scale on the atomizer plate.
- Solution: Clean the surface of the atomizer plate with clear water or clear the foreign bodies in the air inlet screen.
If there is a small amount of mist:
- Cause: There is too much scale or impurity in the water.
- Solution: Clean the atomizer plate and change to clean water.
If there is abnormal noise:
- Cause: The water in the tank is too little and unstable.
- Solution: Fill the tank with water and place the humidifier on a firm surface.
Note:
If the above issues persist, please contact the maintenance point or dealer.
Non-professional personnel should not disassemble or assemble the machine.
Tips
If the switch is turned on but there is no mist:
- Cause: The power supply is not connected or faulty.
- Solution: Reconnect the power supply. If the machine still works abnormally, please contact Deerma after-sales service center.
About usage:
Remove the nozzle cover before filling water into the water tank. Turn the
water tank upside down and open the water tank lid to fill water, or fill
water from the side water filling nozzle. Tighten the water tank lid and
install the water tank on the base. The machine can then be used normally.
Keep your life clean and refreshing all the time. With its micron mist and simply operation so that to deeply moist your skin and each corner in your house. You can enjoy each wonderful moment when you use it.
Product Structure
- Mist nozzle
- Water tank
- Water gauge
- Water tank port
- Knob
- Decorative ring
- Base air inlet
- Base
- Power cord
- Air outlet
- Silicone box
- Float
- Float gland
Electrical Circuit
This diagram is only for reference, and is subject to update without notice. Please in kind prevail. Deerma reserves the right to final interpretation.
Product Parameters
- Product name: Humidifier
- Rated voltage: 220-240V
- Capacity: 5L
- Product size: 219201304mm
- Product model: DEM-F800
- Rated frequency: 50-60Hz
- Rated power: 25W
Operating Principle
Deerma humidifier atomizes water into 1-5μm ultrafine particles by using the
principle that the ultrasonic wave generates 1.7 million high-frequency
oscillations per second, and diffuses water mist into the air through the
pneumatic device to achieve the purpose of uniform air humidification. The
humidifier can maintain the bedroom at ideal humidity and prevent the
generation of static electricity.
Safety Precautions
- Welcome to buy Deerma humid to avoid danger, it must be replaced by the manufacturer or its maintenance department or similar professional maintenance department or full-time personnel.
- If there is any abnormal phenomenon, please immediately disconnect the power plug, and ask the manufacturer or its maintenance department or similar full-time personnel to repair.
- Clean the dust on the power plug regularly.
- Before cleaning or moving, please turn off the power supply and disconnect the power plug.
- When disconnecting the power plug, hold the power plug tightly instead of pulling the power lead.
- Do not move or turn over this product under the condition of power-on or filling with water.
- Do not touch water and parts in the sink when the power is on.
- When the machine is working, do not cover the air inlet and the mist outlet with towels and other articles.
- This product is not a toy. To avoid accidents, please keep it away from babies and children. Do not place it in a crib, stroller or playpen, and do not allow infants and children to play and use the machine.
- Do not use the machine on the inclined surface, but place it in a flat solid place.
- Do not add any essence or other similar substances that are not produced or supervised by our company in the sink and water tank of the machine.
- Do not use the machine in the kitchen, please place it away from the heat source, avoid direct sunlight, and keep it 2 meters away from furniture and other household appliances, and avoid getting damp.
- Please disconnect the plug when filling water.
How to Use
- Lift the water tank out.
- Press the button to open the water gland outward.
- Fill water into the water tank, and control the amount of water according to demand.
- Press the water gland down until “click”.
- Install the water tank filled with water onto the machine body.
- Install the water tank filled with water onto the machine body, plug it in, and turn the knob switch.
Function Description
- After plugging in, the machine is in the standby state;
- Turn the knob clockwise until a beep is heard, and the humidifier is switched on and enters the low-position operation state; continue to turn clockwise, the mist gradually increases to the maximum; then continue to turn counterclockwise, the mist decreases to the minimum until a beep is heard, and the machine is powered off and exits the working state;
- Water shortage protection: in the water shortage state, the reed switch is automatically turned off, and then the machine enters the standby state;
Note: Be sure to disconnect the power cord plug when the machine is not working.
Precautions
- The supply voltage must be equal to the rated voltage of the product. If the supply voltage is inconsistent, please contact the dealer, and do not use the product;
- Please place the humidifier at room temperature for 30 minutes before using it, in case of damage to the water tank caused by sudden temperature change;
- Please use the machine at room temperature (5℃~40℃);
- Please place the machine on a flat surface, and avoid tilting;
- Please do not use the humidifier directly on the wood floor to avoid the deformation and damage to the wood floor;
- Please keep the humidifier 2 meters away from the furniture and electrical appliances to avoid getting damp;
- Keep the humidifier away from heat source and avoid direct sunlight;
- Do not fill hot water above 40℃ into the water tank and the sink not to damage the machine;
- Do not let the water flow from the air outlet into the body, and clean water on the body with dry cloth not to damage the machine;
- When the room temperature is below 0℃, please pour water out of the water tank and the sink to avoid freezing and damage to the machine;
- Do not put metal products, chemicals and detergents into the sink, otherwise there will be a phenomenon of poor atomization;
- Power off and unplug before pouring water out of the tank;
- Power off and unplug if the humidifier needs to be moved, cleaned or filled with water; do not move the machine at will during working;
- Do not fill water into the mist outlet and the air outlet;
- When cleaning, prevent the water getting into the machine;
- Do not disassemble the body parts at will.
Cleaning and Maintenance
- In order to maintain the optimum performance of the humidifier, clean the sink and water tank of the humidifier regularly.
- Prevent the transducer and the filter from accumulating dirt, and clean them frequently; it is difficult to clean stubborn dirt after a long time.
- Before cleaning, power off and disconnect the power plug. When unplugging, hold the power plug tightly instead of pulling the power lead.
- Do not clean the machine surface with chemical solvents, gasoline, polishing powder and other substances, and do not clean the machine with any detergent freely; it is best to clean with clear water.
- Use soft cloth for routine cleaning of all parts. If the scale in the sink cannot be removed by routine cleaning, use the detergent produced or supervised by our company. Dissolve the citric acid with 60℃ hot water (the ratio of water to citric acid is 10mL : 1g), pour it to the scaling part, soak it for 5 minutes, then gently scrub the scaling surface with a brush until the scale is removed.
- Remove the filter from the water tank lid, soak it in the edible white vinegar for 15 minutes, gently shake dozens of times, and then clean with clear water. The function of the cleaned filter is indistinguishable from the new one.
- Regularly change the old water in the sink and water tank to keep the humidifier clean.
- When the machine is not used for a long time, please clean all parts and put them in the original packing box or place them in a dry place after drying.
Fault Analysis and Removal
Turn on the switch but there is no mist
- Cause: The power supply is not connected or faulty
- Solution: Reconnect the power supply. If the machine still works abnormally, please contact Deerma after-sales service center in time.
There is no mist after power-on
- Cause: Check whether the bottom air inlet screen is blocked by foreign bodies, or whether there is a large amount of scale on the atomizer plate.
- Solution: Clean the surface of the atomizer plate with clear water, or clear the foreign bodies in the air inlet screen.
A small amount of mist
- Cause: There is much scale or too much impurity in the water.
- Solution: Clean the atomizer plate and change clean water.
Abnormal noise
- Cause: The water in the tank is too little, and the surface is unstable.
- Solution: Fill the sink with water, and place the humidifier on a firm surface
Note:
If the fault cannot be removed after the above phenomenon analysis, please
contact the maintenance point or dealer of our company. Non-professional
personnel shall not disassemble and assemble the machine.
Tips
About usage:
Remove the nozzle cover before filling water into the water tank, turn the
water tank upside down and open the water tank lid to fill water, or fill
water from the side water filling nozzle, tighten the water tank lid and
install the water tank on the base, and then the machine can be used normally.
About the accumulated water in the base:
the humidifier scatters the liquid water into water mist by the vibration of
the ultrasonic atomizer plate, and the water tank is only a transitional water
storage tool. The sinks of all humidifier bases will accumulate water, please
feel free to use.
About mist amount adjustment:
The humidifier can adjust the fog amount. If there is water around the machine
during use, it will indicate that the room humidity is too high. Please adjust
the fog amount appropriately.
Guangdong Deerma Technology Co., Ltd.
Add:
No. 4-1 Longhui Road, Malong Village Committee, Beijiao Town, Shunde District,
Foshan City, Guangdong Province, China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>