BEACON TRP1 GeoPak Outdoor Lighting Instructions

: June 13, 2024
: BEACON

Table of Contents

BEACON TRP1 GeoPak Outdoor Lighting
Product Information
Product Usage Instructions
TOOLS REQUIRED
MOUNTING PREPARATION
WIRING
FIXTURE MOUNTING
Documents / Resources

BEACON TRP1 GeoPak Outdoor Lighting

Product Information

The product mentioned in the user manual is the TRP1, RDI1, & QSP1. These are fixtures designed for installation in a specific size, known as GEO SIZE1. The fixtures come with easy-to-install mounting brackets. The weight of each fixture is as follows:

TRP1 fixture weighs about 13 lbs
RDI1 fixture weighs about 12 lbs
QSP1 fixture weighs about 13 lbs

Additional parts required for installation, which are not supplied with the product, include silicone caulk, 1/4 wall anchors, and fasteners appropriate for wall construction type.

Product Usage Instructions

Step I – Mounting Preparation:

Before starting, ensure that the power is turned off. Wiring should only be performed by a qualified electrician.
Remove the fixture mounting bracket from the fixture.
Align the holes in the bracket to the matching j-box holes on the wall.
Anchored the bracket to the wall using appropriate hardware.
Pull the supply wires from the junction box, where it meets the wall.

Step II – Wiring:

Follow the wiring diagram provided in Figure 1.

Step III – Fixture Mounting:

Refer to Figure 2 for fixture mounting instructions.

Wall Caulking:

Refer to Figure 1 for wall caulking instructions.

Important Note:

The fixtures are not designed for uplighting. They should only be installed face down.

WARNING! Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to do so may increase the RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH. Install and use so fixture failures do not cause a hazard and use only in environments for which the product is specifically marked.
WARNING! This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
CAUTION! Follow ALL luminaire recommendations, product markings, instructions, restrictions and warnings regarding luminaire operation and burning position. Luminaire label shows electrical and environmental requirements and restrictions.
All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optical system. Any accumulation of dust or dirt should be removed regularly.
Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact your distributor or Lightingtechsupport@currentlighting.com or 864-678-1000 Give instructions to facility owner/manager for future reference.

NOTE:

DO NOT OPEN THIS PRODUCT UNLESS INSTRUCTED BY STEPS INCLUDED IN THESE INSTRUCTIONS OR BY CURRENT LIGHTING TECHNICAL SUPPORT PERSONNEL. FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL MOUNTING BRACKETS.

TOOLS REQUIRED

1/4″ ALLEN WRENCH
DRILL
T-15, T-20 TORX BIT
ANY ADDITIONAL TOOLS NEEDED FOR APPROPRIATE WALL FASTENERS

PARTS REQUIRED:

(SUPPLIED BY OTHERS)
SILICONE CAULK, 1/4” WALL ANCHORS AND FASTENERS APPROPRIATE FOR WALL CONSTRUCTION TYPE

MOUNTING PREPARATION

STEP I – (Figure 1)

POWER MUST BE OFF.
(WIRING MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN)

CAUTION:

TRP FIXTURE WEIGHS ABOUT 13 LBS RDI FIXTURE WEIGHS ABOUT 12 LBS QSP FIXTURE WEIGHS ABOUT 13 LBS
Remove fixture mounting bracket from fixture by
loosing the two hex screws (G).
Align holes in bracket to matching j-box holes.
Secure mounting bracket to j-box.
If no j-box is available, mounting plate must be anchored to wall (hardware by others).
Pull the supply wires (C) from junction box (B).
Apply caulking sealant (supplied by others) around the top and two sides of the bracket where it meets the wall.

WIRING

STEP II (See Fig. 1)

Connect service leads to fixture power leads according to local
and National Electric Codes.
Luminaire is equipped with a universal voltage driver capable of 120V-277V input.
For direct wire connections, connect ground wire to the two green wires. Connect black to line and white to neutral then push connections back inside J-box

FIXTURE MOUNTING

STEP III (See Fig. 2)

Hold fixture at a slight angle, slide over mounting plate and rotate upward to capture plate.
Tighten hex screw (G) securely.
Check to ensure secure mount.
Energize product.

WARNING:

NOT DESIGNED FOR UPLIGHT FIXTURE TO BE INSTALLED FACE DOWN ONLY
Current Lighting
701 Millennium Boulevard
Greenville, SC 29607
Phone: 864-678-1000
©2022 HLI Solutions, Inc. All Rights Reserved. Information and specifications subject to change without notice.
All values are design or typical values when measured under labarotory conditions.
www.beaconproducts.com

Documents / Resources

| BEACON TRP1 GeoPak Outdoor Lighting [pdf] Instructions
TRP1 GeoPak Outdoor Lighting, TRP1, GeoPak Outdoor Lighting, Outdoor Lighting, Lighting
---|---