Beacon LIGHTING 010460 Gypsum 1lt Pendant Instruction Manual

: June 3, 2024
: Beacon LIGHTING

Table of Contents

Beacon LIGHTING 010460 Gypsum 1lt Pendant
Warranty
Installation Requirements
Installation Directions
Safety Tips
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Beacon LIGHTING 010460 Gypsum 1lt Pendant

Thank you for purchasing this quality MFL product . To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

This luminaire is covered by a 12 month warranty. The warranty is from the date of purchase, not the date of installation
If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
Warranty will be void if there is any damage due to improper usage or modification to the luminaire
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

This luminaire m ust be assembled and installed by a licensed electrician
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules. E.g. AS/NZS 3000 Electrical Installations.
This luminaire is a Class I product and must be earthed during wiring and installation.
Do not exceed the maximum wattage rating. This luminaire must be used with LED lamps only.
Select a suitable location for installation:
- This luminaire is suitable for indoor use only
- The mounting point must support 2 times the weight of the luminaire .
- Ensure the luminaire is not installed in the direct line of an air vent/system
- If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty .
Take care not to pull any electrical wires during unpacking as this may damag e the connection.
Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the lumina ire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement
Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work

Installation Directions

Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material. If assembly is required, place the luminaire on a smooth non scratch surface
Loosen the nut from the canopy by looseni ng the grub screw with the Allen key prov ided.
Use the mounting bracket as a template to mark the screw positions on the ceiling (Fig.
C onnect the mains supply wire to the terminal block. Ensure the wires are secure, and no bare wires are exposed.
Mains Supply Wire Luminaire Wire / Terminal block Earth Yellow/Green Yellow/Green or Neutral Blue or Black Blue or N Live Brown or Red Brown or L
NOTE : This luminaire is a Class I product and must be earthed during wiring and installation
Install the mou nting bracket onto the ceiling by using appropriately sized mounting screws and anchors. Ensure the
screws and anchors used are suitable for the mounting surface and the surrounding environment. (Fig. C)
Slide the canopy back up the cord suspension and over the mounting bracket (Fig.
Slide the nut back up the cord suspension and tighten the nut and the grub screw to hold the canopy in place (Fig.
Install a globe (not included) into the lamp holder and s ecure the globe by using the spring clip (Fig. Do not exceed themaximum wattage rating.
After the installation, switch on the luminaire to test and enjoy your new lighting product (Fig.

Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning ,
changing the globe or making any adjustment to the luminaire
To avoid injury or damage to the luminaire , ensure that power leads and screws are secure before connecting the
power.
Select a suitable location away from liquids and hazards.
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc