LiGHTPRO Nina 129P Standing Lamp Instruction Manual
- October 31, 2023
- LiGHTPRO
Table of Contents
Nina 129P
MANUAL AND SAFETY INSTRUCTIONS
12VOLT
MI3825-20190517
TECHNICAL DATA AND CONTENTS OF THE SET
Replaceable Light source
MR16 12V GU5.3
| 3 Watt – LED | Instant full light |
|---|---|
| 190 Lumen | Power factor > 0,5 |
| 3000 Kelvin | Failure < 5% after 1000h |
| 20.000 Hours | Failure < 10% after 6000h |
| On/Off 10.000 | Flux > 80% after 6000h |
| Non dimmable | CRI > 65 |
ASSEMBLY OF THE LIGHTS MUST BE AFFECTED AS SHOWN IN THE PHOTO’S BELOW.
REPLACEABLE LIGHTSOURCE
For questions about parts, service, any complaints or other matters, you can contact us at any time. E-mail: info@lightpro.info
MANUAL AND SAFETY INSTRUCTIONS
Read the safety instructions carefully and follow the advice. Keep these
instructions in case you need them later.
The product you just have bought complies to all european and national
qualifications with respect to the specified LVD (Low Voltage Directive) and
Electro Magnetic Compatibilty (EMC) (89/336/EEG)
SAFETY
- Do not use this product in areas where combustible gases, fumes or liquids may be stored. Install the product a safe distance away from highly flammable materials.
- Always fit this product so that it can still be accessed for servicing or maintenance. This product must never be permanently embedded or bricked in.
- This product is suitable for outdoor use (IP44/IP67, splash-water-proof).
- This product is suitable for outside temperatures of: -20°C.till 50°C
- If the protective glass is broken, it must be replaced before the product is used again!
- The distance away from the surfaces to be illuminated by the product must be a minimum of 0.5 m.
- Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volts.
- Use the correct type of light source and ensure that the maximum wattage is not exceeded. The correct light source is indicated on the (label of the) bracket by a symbol and is the maximum wattage shown.
INSTALLATION OF THE LIGHTS
- Install the products in the desired position and lay the cables so that they can be comfortably connected to the transformer or cables.
- If products are provided with a drain hole for water, this hole must be pointing downwards.
- Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
- Connect the lights to the main cable by using the connector as shown on page 5.
- Plug the plug of the transformer into the wall socket (230 Volt 50 Hz).
REPLACEABLE LIGHTSOURCE
Proceed as follows in order to install or change the light source:
-
Turn the power off.
-
Let the light source cool down for at least 5 minutes.
-
Replace the light source, bearing the following points in mind:
• Only replace the light source by an identical model with the same specifications.
• When (re)assembling, ensure that the parts are dry and clean. -
Turn the power back on.
Proceed as follows if the lamps do not light after you have followed the above instructions:
- Turn the power off.
- Check whether all plugs have been connected properly.
- Check the light source(s) and replace them if necessary.
- Check the transformer and the fuse (if applicable, and have them circuit-tested if necessary).
- Check whether cables have been damaged.
- Turn the power back on.
CONDITIONS OF GUARANTEE
We guarantee the perfect condition and function of this appliance. The
guarantee is valid for 5 years beginning from the date of sale to the end
user. We will rectify all faults arising from defective materials or
manufacturing. The guarantee covers repair or replacement of the defective
parts, subject to our approval. The guarantee does not apply to damage to
parts which are subject to wear and tear nor damage or defects caused by
improper use or incorrect maintenance. The guarantee only applies if the
purchase receipt is sent to the dealer together with the appliance. This
guarantee does not affect your statutory rights.
**** Discarded electrical equipment must not be put in the household waste.
If possible, take it to a recycling company. For details of recycling, contact
a municipal waste processing company or your dealer.