VIVO STAND-TV05L Black TV Cart Instruction Manual
- June 13, 2024
- Vivo
Table of Contents
VIVO STAND-TV05L Black TV Cart
Product Information
- Product Name: Black Mobile TV Cart
- SKU: STAND-TV05L
- Manufacturer: VIVO
- Contact Information: help@vivo-us.com | www.vivo-us.com | 309-278-5303
- Weight Capacity: Cart – 77lbs (35kg), Shelf – 11lbs (5kg)
- Tools Needed: Phillips Screwdriver
Product Usage Instructions
-
Attach the Legs (B) to the Center Base (C) using the M6x35 Screw (S-B) through the sides and M6x16 Screws (S-A) through the top. Use the 5mm Allen Wrench (T-A) to tighten the screws. Install the Casters (J) and adjust them to sit level. Tighten the nuts on the stems against the legs using the Wrench (T-B). Snap the Left Base Cover (K) and Right Base Cover (L) in place and lock the Casters (J) by pressing down on the levers.
-
Install the Column (A) with the Center Base Cover (I) and Base Plate (O) using the M6x50mm Screws (S-C) with 6 Washers (S-D). Make sure the lock and cable hole are in the back. Tighten the screws with the 5mm Allen Wrench (T-A).
-
Install the Cable Grommets (M) and Top Cover (N) to the column. Insert an M6x16mm Screw (S-A) into the back and tighten using the 5mm Allen Wrench (T-A). This screw will function as a stopper to
prevent the column from lowering too far. -
Attach the TV Plate (D) to the Column (A) using the M6x16mm Screws (S-A) with D6 Washers (S-D). Tighten the screws with the 5mm Allen Wrench (T-A).
-
Mount the Shelf (G) and Shelf Support (H) to the column using the M6x16mm Screws (S-A). Tighten them at the desired height using the 5mm Allen Wrench (T-A).
-
Install the Left VESA Bracket (E) and Right VESA Bracket (F) on the back of the TV using the appropriate Screws (M-A thru M-D) with M8 Washers (M-E). Spacers (M-F, M-G) may be required.
-
Hang the TV with the VESA brackets onto the TV plate and tighten the security bolts using a Phillips screwdriver.
-
Organize cables using cable grommets and the cable clip on the back of the shelf support.
-
Loosen the knobs on the VESA brackets to adjust the TV tilt, then retighten them.
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-tv05l
GET IN TOUCH | Monday-Friday from 7:00 am-7:00 pm CST
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity.
We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly, or inappropriate use.
WARNING
CHOKING HAZARD SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION
IS REQUIRED.
TIPOVER WARNING SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
- USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL
- THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Attach Legs (B) to Center Base (C) using M6x35 Screw (S-B) through the sides
and M6x16 Screws (S-A) through the top, and tighten screws with 5mm Allen
Wrench (T-A). Install Casters (J), adjusting if needed to sit level, and
tighten nuts on stems against legs using a Wrench (T-B). Snap the Left Base
Cover (K)and Right Base Cover (L) in place as shown, and lock Casters (J) by
pressing down on the levers.
STEP 2
Install Column (A) with Center Base Cover (I) and Base Plate (O) using M6x50mm
Screws (S-C) with 6 Washers (S-D), making sure the lock and cable hole are in
the back, and tighten with the 5mm Allen Wrench (T-A).
CAUTION: To prevent possible damage or injury due to dropping, do NOT release the column until the lock has fully engaged. Do not attempt to raise the column beyond the MAX line.
STEP 3
Install Cable Grommets (M) and Top Cover (N) to the column. Insert M6x16mm
Screw (S-A) into the back as shown and tighten using a 5mm Allen Wrench (T-A).
The screw will function as a stopper to prevent the column from lowering too
far.
STEP 4
Attach TV Plate (D) to Column (A) using M6x16mm Screws (S-A) with D6 Washers
(S-D) and tighten with 5mm Allen Wrench (T-A).
STEP 5
Mount Shelf (G) and Shelf Support (H) to the column using M6x16mm Screws (S-A)
and tighten at the desired height with a 5mm Allen Wrench (T-A).
STEP 6
Install Left VESA Bracket (E) and Right VESA Bracket (F) on the back of the TV
using appropriate Screws (M-A thru M-D) with M8 Washers (M-E). Spacers (M-F,
M-G) can be required.
STEP 7
Hang TV with VESA brackets onto TV plate as shown, and tighten security bolts
using a Phillips screwdriver.
STEP 8
Organize cables using cable grommets and the cable clip on the back of the
shelf support.
STEP 9
Loosen the knobs on the VESA brackets to adjust the TV tilt, then retighten.
Love your new VIVO setup and want to share?
Tag us in your photo!
Open Monday – Friday 7:00 am – 7:00 pm CST
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black TV Cart for 32" to 70" Screens – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>