GOLDEN LIGHTING 3124-BA3 30.88 Inch 3-Light Dark Rust Vanity Light Instruction Manual
- June 4, 2024
- GOLDEN LIGHTING
Table of Contents
Thank You for Choosing Golden Lighting for Your Lighting Needs!
3124-BA3 30.88 Inch 3-Light Dark Rust Vanity Light
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by an accredited professional.
- Shut off the power supply at the fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixtures from the wall, including the old
mounting strap. THIS A FIXTURE CAN BE INSTALLED ON THE WALL OR CEILING. PLEASE
REVIEW THESE
INSTRUCTIONS FULLY BEFORE PROCEEDING.
-
Mounting strap (A) may be attached to backplate (F). If the mounting strap is attached, remove small screws
(B) to detach. The mounting strap (A) contains several pairs of threaded holes. Find the pair of holes that matches the spacing of the holes on the junction box and your fixture’s backplate. Test backplate (F) on mounting strap (A) to ensure that the backplate will hang straight. Place the fixture aside for future use. -
Pull the house wires through the center of the mounting strap (A). Place mounting strap (A) over the junction box so that mounting screws (D) may be inserted. Secure mounting strap (A) to the junction box with mounting screws (D) and a screwdriver. Tighten the mounting screws (D) securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of the ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
IF INSTALLING A FIXTURE ON THE WALL REFER TO THE DIAGRAM LABELED “(1)”. 4.
Place the fixture’s backplate (F) over the mounting strap (A) so that the
holes in the top of the mounting strap (A) line up with the holes in the
backplate (F). Use a screwdriver to thread screws (B) into backplate (F) until
backplate (F) is snug against the wall. 5. Slide shade (H) over the socket (J)
and secure it in place with socket ring (I). Adjust the arms by loosening
thumbscrews (C) and positioning the arms to the desired placement. Retighten
thumbscrews (C) to secure arms in place. Install a light bulb (not included)
in accordance with the fixture’s specifications. Do not exceed the maximum
recommended wattage. IF INSTALLING A FIXTURE ON THE CEILING REFER TO THE
DIAGRAM LABELED “(2)”. 4. Place the fixture’s canopy (F) over the mounting
strap (A) so that the holes in the top of the mounting strap (A) line up with
the holes in the canopy (F). Use a screwdriver to thread screws (B) into the
holes found on the side of the canopy (F) until the canopy (F) is snug against
the ceiling. 5. Slide shade (H) over the socket (J) and secure in place with
socket ring (I). Adjust the arms by loosening thumbscrews (C) and positioning
the arms to the desired placement. Retighten thumbscrews (C) to secure arms in
place. Install a light bulb (not included) in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage.
Pendants
& Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of the island. Fixtures should hang at least 30″ above the
countertop.
Pendants
& Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>