VIVO STAND-TV70B Black V Base Studio TV Stand Instruction Manual
- June 13, 2024
- Vivo
Table of Contents
Black V-Base Studio TV Stand
Instruction Manual
SKU: STAND-TV70B
STAND-TV70B Black V Base Studio TV Stand
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-tv70b
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
www.vivo-us.com
Chat live with an agent!
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Slide the Feet (C) onto the base of the Leg (A). Insert M8x12mm Screws (S-A)
into the bottom holes of the feet. Tighten with the 5mm Allen Wrench (T-B).
Insert M6x15mm Screws (S-B) through the base into the rear holes of the feet.
Tighten with the 5mm Allen Wrench (T-B). Screw the Foot Pads (F) into the
base, and adjust foot pads to sit level on the floor.
S-B
Screw the Foot Pads (F) into the base, and adjust foot pads to sit level on the floor.
STEP 2
Screw Pole (B) onto Leg (A). Loosen the set screws in Collar (B1) using the
4mm Allen Wrench (T-A). Adjust height of Collar (B1) to the recommended
position below the top of the pole based on your TV’s VESA mounting hole
pattern. Tighten the set screws, making sure they face towards the back of the
stand.
STEP 3
Remove Screw (E1) from the lower VESA Bracket (E) and open the clamp.
STEP 4
OPTION A: Flat Back TV
Position Upper VESA Bracket (D) over top holes on TV and secure with Screws
(M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position Lower VESA
Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8
Washers (M-E).
OPTION B: Curved Back TV
Position Upper VESA Bracket (D) over top holes on TV and secure with Screws
(M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position Lower VESA
Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8
Washers (M-E).
STEP 5
Slide the TV onto assembled stand. Close the clamp on the Lower VESA Bracket
(E) over the pole and secure with previously removed Screw (E1).
STEP 6
Route cables through the cables holes in the Leg (A). Install Cable Covers (G)
to the cables holes, using pliers to break out sections for x2 or x3 cables if
needed.
Anchor TV Stand
OPTION A: Wood Wall Installation
Using Security Cable Clamps (P-C) as guides, mark drilling locations on the
wall.
Use of a stud finder is recommended. Drill holes at least 1.6” (40mm) deep
using a 1/8” (3.5mm) drill bit.
Mount Clamps (P-C) to the wall using ST4.8 x38mm Screws (P-E).
Thread Steel Cable (P-A) through the Security Clips (P-B) on the TV and center holes in the Cable Clamps as shown, then tighten clamps using the 2mm Allen Wrench (P-C).
OPTION B: Concrete/Brick Wall Installation
Using Security Cable Clamps (P-C) as guides, mark drilling locations on the
wall.
Drill holes at least 1.6” (40mm) deep using a 9/32” (7mm) drill bit.
Insert Anchors (P-F) into the holes and mount Clamps (P-C) to the wall using ST4.8 x38mm Screws (P-E).
Thread steel cable (P-A) through the security clips on the TV and center holes in the cable clamps as shown, then tighten clamps using the 2mm Allen wrench (P-D).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 02/08/2023
REV5
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---
www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com| AVG. RESPONSE TIME (within office
hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black V-Base Studio TV Stand for 49" to 70" TVs – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>