PANDUIT CCPLTR3745-X Plastic Trefoil Cable Cleat Instruction Manual
- June 13, 2024
- PANDUIT
Table of Contents
PANDUIT CCPLTR3745-X Plastic Trefoil Cable Cleat
Safety Precautions
| TO REDUCE THE RISK OF INJURY, USER MUST READ INSTALLATION INSTRUCTIONS
BEFORE ATTEMPTING TO INSTALL
---|---
| NOTE: In the interest of higher quality and value, Panduit products are
continually being improved and updated. Consequently, pictures may vary from
the enclosed product.
NOTE: Updates to this Installation Instructions may be available. Check _ _www.panduit.com__ for the latest version of this manual.
---|---
Preparing for Order
| Step | Picture | Description |
|---|---|---|
| 1 | **** | Contact Panduit Sales for assistance with Cleat and hardware |
selection.
2|
| Measure actual diameter of the cables. Select a cleat part number based on
the actual diameter of the cables.
3|
| Measure height of the ladder rung. If using center securing bolt (Method 1), procure M10 or 3/8” hex bolts, washers, and nylon locknuts with sufficient length to pass through the ladder rung. Procure fastening M10 or 3/8” hex bolts based on the chart below. If using side bolts for both securing and fastening (Method 2), procure M10 or 3/8” hex bolts with sufficient length to pass through the ladder rung and the cleat with cables installed. Dock washers can be used to span the opening at the bottom of the rung if there is insufficient clearance between the flanges.
Center Bolt
| Cleat Part Number | Minimum Bolt Length |
|---|---|
| CCPLTR2228-X | 90mm (3 1/2”) |
| CCPLTR2633-X | 90mm (3 1/2”) |
| CCPLTR3139-X | 100mm (4”) |
| CCPLTR3745-X | 100mm (4”) |
| CCPLTR4352-X | 120mm (4 3/4”) |
| CCPLTR5060-X | 120mm (4 3/4”) |
| Step | Picture |
Description
---|---|---
1|
| Assemble M10 or 3/8” fastening bolts through the cleat base. Fully threaded
bolts are shown but not required.
2| ****| Position cleat over the appropriate hole in the rung.
3|
| Assemble M10 or 3/8” securing bolt through the hole in the bottom of the cleat. Tighten to 90 in-lbs [10.2Nm]. Skip to “Securing the Cable” section.
Side Bolts
Step
| Picture|
Description
---|---|---
1|
| Position cleat over the appropriate hole in the rung. Assemble M10 or 3/8”
securing bolt through the holes in the bottom of the cleat. Fully threaded
bolts are shown but not required. Continue to “Securing the Cables” section.
1A|
| OPTIONAL. Thread a
regular hex nut onto each
bolt until it bottoms out on
the bottom plastic shell.
This will hold the bolts in
place. Nuts do not need
to be removed before
assembly. Requires fully
threaded bolt. Continue
to “Securing the Cables”
section.
Securing the Cables
Step
| Picture|
Description
---|---|---
1|
| Place cables in the opening between the fastening bolts, careful not to
damage the cables on the bolts. Center securing bolt is not used if using
Method 2.
2|
| Assemble top of cleat on fastening bolts.
3|
| Assemble washer and nylon locknut on fastening bolts. Tighten to 90 in-lbs
[10.2Nm]. Ensure top remains level during tightening process.
END| ****| Completed product.
Customers Support
Email:
techsupport@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter@panduit.com
Panduit Corp.
USA Technical Support
Tel: 800-777-3300
Panduit Europe • EMEA Service Center
Tel: +31 546 580 452 • Fax: +31 546 580 441
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>