LEDOLUX Hermes LT Microwave Instruction Manual
- June 13, 2024
- LEDOLUX
Table of Contents
LEDOLUX Hermes LT Microwave
Product Information
- Product Name: HERMES LT MICROWAVE
- Power: 15W, 30W
- Dimensions: L 1270mm x W 70mm x H 110mm (15W) / L 1270mm x W 55mm x H 55mm (30W)
- Weight: 1.6kg (15W), 1.8kg (30W)
- Application: Industrial facilities, Warehouses, Sport facilities, Commercial facilities
- Manufacturer: Ledolux Poland Sp. z o.o.
Contact Information:
- E-mail : info@ledolux.pl
- Tel : +48 696 966 622
- Date: 07.03.2023
Technical Specifications
- Nominal Voltage: 210 – 240V ~
- Frequency: 50 / 60Hz
- Colour Temperature: 4000K
- Luminous Efficacy: 120lm/W
- Mounting Height: 2 – 5m
Product Usage Instructions
- Fix the screws on the ceiling. Attach the mounting cables.
- Adjust the length of the cables. Lock the length by turning the clamping handle. Attach the mounting bracket to the cables.
- Fix the luminaire to the mounting bracket. Connect the luminaire to the power supply according to the wire marking provided. Install the LED lamps in the luminaire and close the housing by snapping all the clips.
DIMENSIONS
| DIMENSIONS| L| W| H| Waga
---|---|---|---|---|---
15W| 1| 1270mm| 70mm| 55mm| 1.6kg
30W| 2| 1270mm| 110mm| 55mm| 1.8kg
Instruction manual
- NOMINAL VOLTAGE: 210 – 240V ~
- FREQUENCY: 50 / 60Hz
- COLOUR TEMPERATURE: 4000K
- LUMINOUS EFFICACY: 120lm/W
- BEAM ANGLE: 120°
- OPERATING TEMPERATURE: -20°C ÷ +50°C
- MOUNTING HEIGHT: 2 – 5m
Suspended mounting
- Fix the screws on the ceiling. Attach the mounting cables.
- Adjust the length of the cables. Lock the length by turning the clamping handle. Attach the mounting bracket to the cables.
- Fix the luminaire to the mounting bracket. Connect the luminaire to the power supply according to wire marking below. Install the LED lamps in the luminaire and close the housing by snapping all the clips.
Ceiling mounting
- Drill holes with a 6mm diameter drill, and attach the mounting brackets to the ceiling.
- Mount the luminaire in the mounting bracket.
- Connect the luminaire to the power supply according to wire marking below. Install the LED lamps in the luminaire and close the housing by snapping all the clips.
Connecting the power cable
NOTE
Installation must be performed by a qualified person. In case of doubts as to
the installation or use of the LED luminaire, consult the manufacturer
Replace the luminaire after a failure. Self-repair shall void the warranty.
This product contains a light source with energy efficiency class D.
Do not install the luminaire in an environment with high chemical exposure
(e.g. chemical factories, animal pens).
Keep the luminaire in a cool, dry and clean environment. Keep away from water
and fire.
Make sure you disconnect the power supply before installation. Turn on the
power after connecting and securing all luminaires in the circuit.
The light source used in this luminaire should only be replaced by the
manufacturer or their service representative, or a similarly qualified person.
Protect your eyes, and avoid looking at the light for a long period of time.
Dirtiness that settles down on the luminaire due to normal operation shall be
cleaned with a damp cloth. Do not use invasive cleaners or cleaning methods.
APPLICATION
- Industrial facilities
- Warehouses
- Sport facilities
- Commercial facilities
- E-mail : info@ledolux.pl
- Tel : +48 696 966 622
- Date : 07.03.2023
We reserve the right to make design changes to luminaires.