Honeywell SLN 700 SmartLine Level Non-Contact Radar Installation Guide
- June 6, 2024
- Honeywell
Table of Contents
- Honeywell SLN 700 SmartLine Level Non-Contact Radar
- INTRODUCTION
- MOUNTING THE TRANSMITTER
- Installation position
- Conduit Entry Plugs and Adaptors
- WIRING
- Hazardous Locations & Intrinsic Safety
- EU Declaration of Conformity
- EMC Conformity
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Honeywell SLN 700 SmartLine Level Non-Contact Radar
This document provides descriptions and procedures for the quick installation
of Honeywell’s SmartLine Non-Contact Radar Level Transmitters.
The SmartLine Level Non-Contact Radar is available as a family of SLN72x
models for liquid and solid applications.
Copyrights, Notices and Trademarks
Copyright 2020 by Honeywell
Revision 1.0, July 2020
Trademarks
SFC, SmartLine, ST 800 and ST 700 are U.S. registered trademarks of Honeywell
Inc.
HART® and FOUNDATION™ are trademarks of the FieldComm Group™
Documentation
To access complete documentation, including language variants, scan the QR
code below using your smart phone/device or QR code scanner.
Go to the APP store for your free Smartphone QR scanner
Or you can follow the URL to access the online SmartLine HUB page.
The HUB page will contain direct links to open SmartLine product
documentation.
https://hwll.co/SmartLineHUB
INTRODUCTION
The Smartline SLN700L is available for both liquid and solid non-contact radar level measurement. Each model is available with a range of flange or threaded antenna, lens diameters, process connection, and accessories to suit most applications. Mounting the Transmitter
INSTALLATION
Evaluate the site selected for the SmartLine SLN700 installation with respect
to the process system design specifications in table 1. Please note that the
display can become unreadable below -20C (-4°F) but it will recover once the
temperature increases.
Operating conditions
Table 1: Operating Conditions
P arameter
|
Operative Limits
| T r ansportation and Storage
---|---|---
° C| ° F| ° C| ° F
A m b i ent Temperature 1| -25 to 80| -13 to 176|
-40 to 80| -40 to 176
H u m i d ity %RH| 0 to 100| 0 to 100
Process Connector
The 80 GHz non-contact radar transmitter has three different series of
products and associated process connections.
Table 2: Process Connectors
S eries| M edium| A pp lications| P r
o cess connections
---|---|---|---
82 Series| Liquid| Strong corrosive liquid vapors or foam| Flange
options
83 Series| Liquid| Strong corrosive or pressure resistant liquid| Thread
options
87 Series| Solid| Storage vessel/proces s vessel or high dust
applications| Flange options
For list of all options and accessories please refer to the product specifications, which is available, here: https://www.honeywellprocess.com /smartline-level-transmitter.aspx.
MOUNTING THE TRANSMITTER
There should be no obstacles in the area radiated by the transmitted microwave
beam from the lower edge of the antenna to the material surface to be measured
within the cone angle of the radar beam. These obstacles include ladders,
limit switches, heating equipment, supports, etc. When these are unavoidable,
the gauge offers background subtraction (“Virtual Echo Learning”) so that
obstacles will be ignored during level measurement. In addition, please note
that the microwave beam should not intersect with tank fluid in or out flows.
In addition, the highest liquid or solid tank level should not encroach into
the upper blocking distance of the gauge
(typically a few cm). (see Figure 1), The instrument should be kept at a
certain distance from the tank wall and the transmitting antenna should be
perpendicular to the measured material surface as much as possible.
The instruments installed in a hazardous classified area shall follow the
local national installation regulations.
The reference plane for measurement is the sealing surface of threads or
flanges.
- Near (blocking) distance
- Far distance
- Distance at which sensor reads 100% level (or current)
- Distance at which sensor reads 0 % level (or current)
Installation position
The minimum distance between the antenna and tank wall is variable for different antenna. Please refer to Table 3.to calculate the minimum distance for your particular model. In no instance, should the instrument be mounted closer than 200 mm to the tank wall.
- Reference plane
- Center of the vessel or symmetry axis
Table 3: Minimal distance to tank wall
| S L N 700 Model | M in distance to tank wall |
|---|---|
| 83A | 1/5 × Tank Height |
| 82A 82B 83B 83C | 1/10 × Tank Height |
82C 82D 83D 83E
87A 87B 87C 87D
| 1/20 × Tank Height
For a conical vessel with a flat tank top, the best installation position of the instrument is the top center of the vessel, which ensures that the bottom of the container is measured.
Nozzle installations
In the case of a tank fluid or solid with good reflection properties (high
dielectric constant), the sensor may be mounted on a nozzle. The background
subtraction (“virtual echo learning”) feature can further reduce false echoes
from nozzle openings.
Table 4 shows detail of the size limitations of the nozzle.
Table 4: Nozzle specification table
N o zzle Diameter d （ mm ）| M aximum Nozzle
Height h （ mm ）
---|---
83A| 82A 82B
83B 83C
| 82C 82D
83D 83E
| 87A 87B
87C 87D
40| 150| NA| NA| NA
50| 150| 150| NA| NA
80| 200| 200| 200| NA
100| 300| 300| 300| 300
125| 400| 400| 400| 400
150| 500| 500| 500| 500
If there are agitators in the tank, the instrument should be installed as far away from these as possible. Once the installation is completed, the “”virtual echo learning” should be carried out while the agitators are running. This will eliminate the influence of false echo generated by mixing blades. If foam, strong liquid agitation or only a narrow clear volume is available then the customer should consider a guided wave radar sensor such as the Honeywell SLG-700 series.
Conduit Entry Plugs and Adaptors
Procedures
It is the User/Installer’s responsibility to install the transmitters in
accordance with national and local code requirements. Conduit entry plugs and
adapters shall be suitable for the environment, shall be certified for the
hazardous location when required and acceptable to the authority having
jurisdiction for the plant.
CONDUIT ENTRY PRECAUTIONARY NOTICE
THE CONDUIT/CABLE GLAND ENTRIES OF THIS PRODUCT ARE SUPPLIED WITH PLASTIC DUST
CAPS WHICH ARE NOT TO BE USED IN SERVICE. IT IS THE USER’S RESPONSIBILITY TO
REPLACE THE DUST CAPS WITH CABLE GLANDS, ADAPTORS AND/OR BLANKING PLUGS WHICH
ARE SUITABLE FOR THE ENVIRONMENT INTO WHICH THIS PRODUCT WILL BE INSTALLED.
THIS INCLUDES ENSURING COMPLIANCE WITH HAZARDOUS LOCATION REQUIREMENTS AND
REQUIREMENTS OF OTHER GOVERNING AUTHORITIES AS APPLICABLE
Use the following procedures for installation.
Conduit Entry Plugs
| S tep | A ction |
|---|---|
| 1 | Remove the protective plastic cap from the threaded conduit entry. |
2
| To ensure the environmental ingress protection rating on tapered thread (NPT), a non-hardening thread sealant may be used.
3
| Thread the appropriate size conduit plug (M20 or ½” NPT) into the conduit entry opening. Do not install conduit entry plugs in conduit entry openings if adapters or reducers will be used.
4
| Tighten adapters according to the following torque: Torque: 32 Nm or 24 lb- ft
Note: Plugs do not come installed in the housings. All housings come with temporary plastic dust protectors (red or blue) installed and are not certified for use in any installation.
WIRING
Wiring must comply with local codes, regulations and ordinances. Grounding may be required to meet various approval body certification, for example CE conformity. Refer to the SmartLine Level Non-Contact Radar User’s Manual, Document #34-SL-25-13.
HART / 4-20mA Operating Ranges
The Power supply and the output current signal are carried by the same two-
core cable. The allowed supply voltage range is 12V to 30Vdepending on loop
resistance. There must always be between 12V and 30V on the transmitter
terminals, regardless of loop current. A safety barrier (refer to Table 5 for
detailed specification) should be placed between the power supply and
instrument for the intrinsically safe version.
The grounding mode of current output can be adopted for the standard
instrument, while the floating current output should be adopted for the
intrinsically safe instrument. Normally, the grounding terminals can be
connected to the grounding point of tank or an available nearby ground in case
of plastic tank.
Maximum Loop Resistance (Ω)
Table 5: Maximum Loop Resistance (Ω)
S u pp ly Voltage (VDC)| M ax. Loop Resistance (
Ω )
---|---
12| 0
17.5| 250
23| 500
30| 818
A regular two conductor cable can be used as the power supply cable, and the
outside diameter of the cable should be (5-9) mm to ensure the sealing of
cable entry. The two ends of the shielded cable should be grounded only where
allowed by the installation location. In hazardous locations, only one end of
the cable can be shielded, typically on the non-hazardous side.
Remove the display to access the wiring connections
Note: For intrinsically safe installations, shield is normally terminated at one end only
Hazardous Locations & Intrinsic Safety
See manual for Special Conditions of safe use
Table 6: Hazardous Location Ratings
| A GENCY | T YP E OF PROTECTION |
|---|---|
| IECEx TUR 20.0056X | Intrinsically Safe: Ex ia IIC T6…T2 Ga |
Ex ia IIIC T85˚C…T300˚C Da
ATEX
TÜV 20 ATEX 8576 X
| Intrinsically Safe:
II 1 G Ex ia IIC T6…T2 Ga
II 1 D Ex ia IIIC T85˚C…T300˚C Da
Table 7: Intrinsic Safety Entity Parameters
I n t r insic Safety Entity Parameter| 4-20mA
T erminal 1 & 2
| RS 485
T erminal 1
& 2
| RS 485
T erminal 4
& 5
---|---|---|---
Ui| 30.6V| 26.4V| 6.5V
Ii| 131mA| 166mA| 68mA
Pi| 1.0W| 1.1W| 111mW
Ci| 0| 0| 102μF
Li| 102μH| 0| 0
Table 8: Process Temperature Vs Temperature Class
T r ansmitter Ambient
temperature ( ℃ )
| P r o cess Temperature at the
antenna ( ℃ )
| T emperature Class of entire equipment
---|---|---
-40 to +50| -40 to +50| T6/85C
-40 to +60| -40 to +95| T5/100C
-40 to +70| -40 to +130| T4/135C
-40 to +195| T3/200C
-40 to +200| T2/300C
EU Declaration of Conformity
Hereby, Honeywell International Inc. declares that the SLN700 Radar Level
Transmitters are in compliance with the directives listed below.
The full text of the EU declaration of conformity is available at the
following internet
address:
https://www.honeywellprocess.com/library/support/Public/Documents/50164363.pdf
The SLN700 transmitters comply with the following directives
D I R E C T I V E| DESC R I
P T I ON
---|---
2014/53/EU| Radio Equipment Directive
2014/34/EU| ATEX Directive
2011/65/EU &
2015/863
| Restriction of Hazardous Substances Directive
EMC Conformity
The SLN700 transmitters comply with the following EMC standards
| STANDARD | DESCRIPTION |
|---|
EN 301 489-1 V2.2.0
| ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
EN 301 489-3 V2.1.1| ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 3: Specific conditions for Short-Range Devices
(SRD) operating on frequencies between 9 kHz and 246 GHz
EN 302 729 V2.1.1| Short Range Devices (SRD);
Level Probing Radar (LPR) equipment operating in the frequency ranges 6 GHz to 8,5 GHz, 24,05 GHz to 26,5 GHz, 57 GHz
to 64 GHz, 75 GHz to 85 GHz
EN 302 372 V2.1.1| Short Range Devices (SRD); Tank Level Probing Radar (TLPR)
equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6
GHz, 24,05 GHz to 27 GHz, 57 GHz to 64
GHz, 75 GHz to 85 GHz
EN 62311:2008| Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz
– 300 GHz)
T a b l e 9 : Display Men u Tree Basic Settings, Display and Diagnostics
| L evel 1 / Menu no| L evel 2 / Menu no.| L evel 3| L evel 4| L evel 5|
1.Basic Settings
|
1.1 Medium
|
Liquid
| Rapid Material Change| Y N
First Echo| Normal Small Big Bigger Biggest
Surface Wave| Y N
Low DK| Y N
Solid
| Rapid Material Change| Y N
First Echo| Normal Small Big Bigger Biggest
Large Angle of Repose| Y N
Strong Dust| Y N
Low DK| Y N
1.2 Unit of measurement| m / ft / inch
/cm / mm
| |
1.3 Near blanking| | |
1.4 Range| | |
1.5 Minimum Adjustment| | |
1.6 Maximum Adjustment| | |
1.7 Current Output| 4-20mA /
20-4mA
| |
1.8 Sensor Tag| | |
L evel 1 / Menu no| L evel 2 / Menu no.| L evel 3|
L evel 4| L evel 5
---|---|---|---|---
2. Display
| 2.1 Display Value| Distance / Height / Percent| |
2.2
Language
| Chinese / English| |
3.
D iagnostics
| 3.1 Choose Curve| Eff Curve / Echo Curve / False Echo / Log curve| |
3.2 Start Simulation| Current/Distance| |
3.3 Sensor Status| T/ DB/Volt/Service Time| |
3.4 Measure status| Max Volt / Min Volt /
Min Volt Time
| |
3.5 Peak Values| Max Distance / Min Distance| |
3.6
Calibration Date
| | |
Sales and Service
For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one of the offices below.
ASIA PACIFIC (TAC) hfs-tac-support@honeywell.com
Australia Honeywell Limited, Phone: +(61) 7-3846 1255, FAX: +(61) 7-3840 6481
Toll Free 1300-36-39-36, Toll Free Fax: 1300-36-04-70
China – PRC – Shanghai, Honeywell China Inc. Phone: (86-21) 5257-4568,
Fax: (86-21) 6237-2826
Singapore, Honeywell Pte Ltd. Phone: +(65) 6580 3278. Fax: +(65) 6445-3033
South Korea, Honeywell Korea Co Ltd. Phone:+(822)799 6114. Fax:+(822) 792 9015
EMEA, Phone: + 80012026455 or +44 (0)1202645583. FAX: +44 (0) 1344 655554
Email: (Sales) sc-cp-apps-salespa62@honeywell.com
or (TAC) hfs-tac-support@honeywell.com
AMERICAS, Honeywell Process Solutions,
Phone: (TAC) 1-800-423-9883 or
215/641-3610. (Sales) 1-800-343-0228.
Email: (Sales) FP-Sales-Apps@Honeywell.com
or (TAC) hfs-tac-support@honeywell.com
For more information
To learn more about SmartLine Transmitters, visit
www.honeywellprocess.com Or contact your
Honeywell Account Manager
Process Solutions
Honeywell
1250 W Sam Houston Pkwy S
Houston, TX 77042
Honeywell Control Systems Ltd
Honeywell House, Skimped Hill Lane
Bracknell, England, RG12 1EB
Shanghai City Centre, 100 Jungi Road
Shanghai, China 20061
www.honeywellprocess.com
34-SL 25-14, Rev.2
November 2020
2020 Honeywell International Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>