LEDOLUX LUXA DOB ZEBRA Intelligent LED Street Luminaire User Guide

: June 13, 2024
: LEDOLUX

Table of Contents

DIMENSION
WARNING
INSTALLATION
LUMINAIRE SERVICE
NEMA socket
CUSTOMERS SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LEDOLUX LUXA DOB ZEBRA Intelligent LED Street Luminaire

DIMENSION

P /P in [W]| Wymiary L × W × H [mm]| Powierzchnia [m 2 ]| Powierzchnia boczna [m 2 ]| Waga [kg]
---|---|---|---|---
0 – 35| 650×220×108| 0.1218| 0.0271| 4.3
36 – 50| 650×220×108| 0.1218| 0.0271| 4.3
51 – 70| 720×270×109| 0.1611| 0.0293| 5.8
71 – 100| 840×320×109| 0.2079| 0.0337| 7.3
101 – 150| 840×320×109| 0.2079| 0.0337| 7.3

NOMINAL VOLTAGE 205 – 250V ~
FREQUENCY 50 / 60Hz
COLOUR TEMPERATURE 2700K / 4000K / 6000K
LUMINOUS EFFICACY 170lm/W
BEAM ANGLE Asymmetric
OPERATING TEMPERATURE -40°C ÷ +40°C
MOUNTING HEIGHT 4 – 10m

WARNING

When installing luminaires on composite poles, it is absolutely necessary to ground the fixture by connecting the PE wire to the knife terminal inside the luminaire. In case of any problems in this matter, please consult the manufacturer.

Mounting diameter

Ø45 – 60mm

The outer diameter of the electric wire

min max
Ø7 – 10mm

INSTALLATION

Make sure you disconnect the power supply before installation.
Open the luminaire housing.
After servicing, disassemble the service body. Then while squeezing the locking pins, fix the upper part of the housing.
The upper housing should be mounted on both hinges.
Check the position of the gasket and its cleanliness (all solid parts must be removed). Close the luminaire and press it with the clips (properly closed, it should make a loud “click”). The serviced luminaire does not require re-positioning on the pole.

LUMINAIRE SERVICE

CAUTION, risk of electric shock. Open the luminaire. After opening, the power supply in the upper part of luminaire body is disconnected.
Tilt the upper part of the luminaire body as far as possible.
UWAGA, ryzyko porażenia prądem elektrycznym w dolnej części korpusu. Dolną część korpusu zabezpiecz przed warunkami atmosferycznymi oraz przedostawaniem się zanieczyszczeń, dedykowanym w tym celu korpusem serwisowym.

Place the power cord from the pole to inside the luminaire – 2×1.5mm wire. Adjust the length of the cable, then lock the cable by tightening the cable gland with 2 flat wrenches (20mm, 10Nm).

Connect the power cord to the blade terminal M29 as specified below.

Characteristic of the blade terminal
Number of terminals 3
Rated voltage 500V
Rated current 16A
Rated connecting capacity 1.5-4mm2
Preparation of the power cable
NOTE
Use wires with double insulation .

Applies to the connection of control cables.

Place the lamp on the pole or the extension arm by securing it with the fixing screws by means of a hex wrench (6mm, 3.5Nm), and countering it with a flat wrench (13mm, 10Nm).

6A. STANDARD
Adjust the angle of inclination of the luminaire by adjusting the screws at the mounting bracket with a hex key (6mm, 3.5Nm).

6B. Bracket 90D
Adjust the angle of inclination of the luminaire by adjusting the screws at the mounting bracket with a hex key (8mm, 5Nm).

NEMA socket

Attach the controller to the NEMA socket by pressing and turning as indicated on the controller. If there is no controller, secure the NEMA socket by installing a special Jumper.

NOTE

Installation must be performed by a qualified person. In case of doubts as to the installation or use of the LED luminaire, consult manufacturer.

The luminaire should be installed in dry weather conditions to avoid the entrapment of moisture inside the luminaire, which may lead to corrosion of electrical components and damage to the luminaire. The luminaire should not be installed during rainfall or high air humidity.

This product contains a light source with energy efficiency class B.

For luminaires without 0-10V controller, the connection point for control wires (+, -) should be left empty.

Do not ground the terminal provided for the control wires (+, -).

Replace the luminaire after a failure. Self Repair shall void the warranty.

Keep the luminaire in a cool, dry and clean environment. Keep away from water and fire.

Make sure you disconnect the power supply before installation. Turn on the power after connecting and securing all luminaires in the circuit.

The light source used in this luminaire should only be replaced by the manufacturer or their service representative, or a similarly qualified person.

Protect your eyes, avoid looking at the light for a long period of time.

Dirtiness that settle down on the luminaire due to normal operation shall be cleaned with a damp cloth. Do not use invasive cleaners or cleaning methods.

APPLICATION