eta 1244 90000 Rondo Robotic Vacuum Cleaner User Manual

: June 13, 2024
: ETA

Table of Contents

Product Information
Product Usage Instructions
CHARGER STATION INSTALLATION
OVERVIEW OF LIGHT SIGNALS
VACUUM CLEANER MAINTENANCE
PROBLEMS SOLUTIONS
TECHNICAL SPECIFICATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

eta 1244 90000 Rondo Robotic Vacuum Cleaner

eta-1244-90000-Rondo-Robotic-Vacuum-Cleaner-
PRODUCT

Product Information

Product Name: Rondo Model
Number: eta 1244
Battery Type: Li-Ion
Battery Capacity: 4000 mAh
Operating Time: 5-6 hours
Weight: 2.05 kg
Wireless Connectivity: 2.4 / 5 GHz
Wi-Fi Signal Strength: 17.5 dBm

Product Usage Instructions

Before using the Rondo, please read and keep the user manual, receipt, and the box with the internal packing.

General Safety Instructions:

Follow all safety warnings provided in the user manual.
Regularly replace and maintain all filters and use only original filters.
Do not disassemble, maintain, or transform the product by yourself. Contact designated maintenance technicians for any issues.
Do not touch the high-voltage power cord with wet hands to avoid electric shock.
Do not use the cleaner outdoors.
Use only the provided charger for charging the Robot.
Avoid bending the power cord excessively or placing weight on it to prevent damage, fire, or electric shock.
Keep the Rondo away from heat sources, such as cigarettes, lighters, matches, and combustible materials

Wireless Connection and Compatibility:

The Rondo supports wireless connectivity through Wi-Fi. – It operates on 2.4 / 5 GHz frequency bands.
The signal strength is 17.5 dBm. – Ensure that your Wi-Fi network is compatible with the Rondo’s frequency bands.

For further assistance and information on using the Rondo, visit www.eta.cz/robot/. Please note that the above instructions are a general overview. For detailed usage instructions and safety guidelines, please refer to the complete user manual included with the product.

INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Keep these instructions, the receipt, and, if possible, the box with the internal packing.

GENERAL SAFETY INSTRUCTIONS

Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
Check whether the data on the type label correspond with the voltage in the electric
Never use the appliance if its power cord or adaptor is damaged, if it does not work properly, or if it fell and was In this

case take the appliance to a special service to check its safety and proper function.

The product is intended for home use and similar (in shops, offices, and similar workplaces, in hotels, motels, and other

residential environments, and facilities providing accommodation with breakfast). It is not intended for commercial use!

This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
Before replacing accessories or accessible parts, that move during operation, before assembly and disassembly, and before cleaning or maintenance, turn off the appliance!
If the power cord of the adaptor is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person to prevent dangerous situations.
Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell and was damaged, or if it fell into the water. In this case, take the appliance to a special service to check its safety and proper function.
To ensure the safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.
If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person to prevent dangerous situations
WARNING : To charge the battery, use only the network adapter supplied with this appliance.
To power the appliance, only apply a safe small voltage by the type plate.
Don´t put hands close to rotating
Never immerse the vacuum cleaner in water (even its parts)!
Never vacuum without a properly inserted filtration system and micro-
Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items (e.g. ash, hot cigarette butts, gasoline, thinners, and aerosol vapors) or greases (e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these objects may lead to damage to the dust filters or the vacuum cleaner.
Pores of the filters may be clogged when vacuum cleaning very fine dust (e.g. fine sand, cement dust, plaster). Thus, air permeability will be reduced and the suction performance will In this case, clean the filters even though the dust container is not full yet.
Always switch off the vacuum cleaner first and disconnect the power cord from the power supply and only then empty the dust container, clean/replace micro-filters, and clean the vacuum cleaner or its accessories.
Never leave the vacuum cleaner exposed to weather conditions (rain, frost, direct sun radiation, ).
Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!
Disconnect the appliance from the mains when not in use for a long Switch off the vacuum cleaner and slide it out of the contacts of the charging station.
Secure please gaps on the floor (e.g., Threshold Strip) to avoid damaging the rotating brushes. These joints may also limit the vacuum cleaner jams bristle of brush into the
This device can not be used on a carpet whose pile length is over 1 cm. At the same time, the vacuum cleaner may not function properly on some types of dark carpets whose surface „deceives” the sensors and can cause chaotic movements of the vacuum cleaner or its failure to reach some parts of the floor. Robot vacuum cleaners can cross floor transition strips of approx. 2 cm in height.
Make precautions to solve the problem which may cause the cleaning in trouble, such as:
- Keep the easily knocked-over objects in a safe
- Permian the edge of the
- The hanging tablecloth and curtain should not touch the
- The flammable object should be cut from the fire
- Sort out the tangled power cord on the
- Pick up the newspaper, book, magazine, and large piece of paper scattered on the
Check whether the main brush is correctly fixed inside the robot before
Examine if the dustbin is empty and ensure it is fixed before it
See if up-ground height sensors are wiped
If you only need to clean one room, please close the
If the room that needs to be cleaned wants a partition, you can place the virtual wall and, at the same time, check the facing opening width.
Please be aware that the device needs 9 cm of clearance underneath furniture so that it will not become trapped.
Do NOT drop the Robot, should this happen, run the Robot to see that everything is okay before letting it operate by itself without you being present.
If the battery is leaking, remove it immediately; it can damage the vacuum
Keep batteries out of reach of children and incapacitated A person, who would swallow the batteries, must seek medical help immediately.
Dispose of a discharged battery in a suitable
Never use the appliance for any other purpose than for the intended one described in these instructions for use! This appliance is not intended for outdoor use.
The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied Failure to replace or maintain all filters regularly and also using non-original filters, the properties of which resulted in failure or damage of the vacuum cleaner is also understood to be improper use of the appliance.

Wireless connection and compatibility

The ETA company cannot be liable in any way for any incidental, indirect, or consequential damages, or for any loss of data or loss due to information leakage during wireless communication.
Successful wireless communication cannot be guaranteed 100% on all Smart devices and WiFi networks (routers). Due to the variety of devices on the market, there may be cases where the character or specification of a given smart device or Wi-Fi network (router) makes connection impossible or is in some way disturbed. In addition, several factors, including hardware and software configuration, also affect the success of wireless communication over a Wi-Fi network. The connection between the robot and your Wi-Fi network can also be adversely affected by the surrounding Wi-Fi networks that they can be tuned to the same channel and disrupt connections (e.g. in housing estates, apartment buildings, etc.). These facts are not a reason to claim the appliance.

The application is owned and operated by a third party (hereinafter the “Subject”) different from HP TRONIC Zlín, Ltd. (hereinafter the „Seller“). No personal information is transmitted between the Subject and the Seller. When registering for the application, the customer transfers the personal data directly to the Subject, which becomes the personal data controller. The Application and the associated privacy policy are governed by the Rules of the Subject

| No one else can disassemble the main- main. Transform the product except for the maintenance technicians designated by our company or it may cause fire electric shock or personal injury.|

| Don’t use other charger but the equipped one of the Robot, or it may cause product damage,

electric shock or fire due to high voltage.

---|---|---|---
| Don’t touch the high-voltage power cord of the electric appliance with your wet hand, or it may cause an electric shock.| | Don’t bend the power cord overly or place weight on it, or it may cause power cord damage, fire, or electric shock.
|

Don’t use the Cleaner outdoors, or it may cause the product damage.

| | Don’t approach cigarettes, lighters, matches, and other heat objects or combustible materials such as gasoline cleaners.
| Don’t use the Cleaner in commercial places, or the Cleaner may be damaged by excessive use.| | Insert the power cord of the charger well or it may cause electric shock, short circuit, smoking, or fire.
---|---|---|---

|

Check whether the adapter and connector are connected well, or it may cause charging failure or even fire.

|

| Remove all easily damaged objects (including luminous objects, fabrics, glass bottles, etc.) before using,

or it may cause damage to these objects or affect the use of the cleaner.

| Please use the Cleaner cautiously in the presence of the children to avoid frightening or harming them.| | Don’t stand or sit on the Cleaner, or it may cause damage to the Cleaner or personal injury.
| Don’t make the Cleaner take in water and other liquors for fear of the product damage.| | Don’t use the Cleaner on small tables and chairs or other small spaces, otherwise, the Cleaner may be damaged.

APPLICABILITY

The product, mainly applicable to homes, hotel rooms, and small offices, is good for cleaning to various short-haired carpets, wood floors, hard floors, ceramic tiles, etc. Since the vacuum cleaner moves freely in the space of your home, it is necessary to adapt the environment to this fact. Before use, remove all unwanted objects (stretched cables, scattered clothes, papers, bags, etc.) from the floor that could impede the movement of the vacuum cleaner or, conversely, fragile objects (e.g. glass and ceramic vases) that could be damaged by the vacuum cleaner.

If you use the device in an apartment with several stories, it is necessary to carry the charging station along with the device from one story to another.

PRODUCT COMPONENTS
PACKAGE CONTENTS $eta-1244-90000-Rondo-Robotic-Vacuum-Cleaner-FIG- $2$$

ROBOTIC VACUUM CLEANER

$eta-1244-90000-Rondo-Robotic-Vacuum-Cleaner-FIG- $3$$

A: Robotic vacuum cleaner
A1: Front bumper
A2: Sensors against falling downstairs
A3: Charging contacts
A4: Storage battery compartment cover
A5: Drive Wheels (Left / Right)
A6: Front wheel
A7: Side brushes
A8: Dust cover
A9: Powerd cord connector

DUSTBIN

B: Dust bin
B1: Release button
B2: Lid of dust bin
B3: Filter cover
B4: HEPA filter
B5: Foam filter

CONTROL PANEL

C: Control panel
C1: ON /OFF/AUTO (automatic cleaning) / STOP (PAUSE) button
C2: CHARGING / STOP (PAUSE)
C3: LOCAL CLEANING button / STOP (PAUSE)
C4: Wifi indicator
C5: Charging indicator

CHARGER STATION

D: Charger station
D1: Operation indicator
D2: Signalisation area
D3: Charging contacts
D4: Adapter connection port

REMOTE CONTROL

F: Remote control
F1: ON /OFF to stand-by mode
F2: Directional buttons for manual control (FORWARD /RIGHT/ LEFT/BACK)
F3: Local cleaning mode
F4: Back to charger station
F5: Automatic cleaning mode
F6: Edge cleaning mode / STOP (PAUSE)
F7: STOP (PAUSE) / START

Remote control notes

Do not combine various types of batteries. Do not even combine used and new batteries.
Batteries not intended for this purpose must not be charged.
Rechargeable batteries must be removed from the appliance before charging.
Remove the batteries if you will not be using the appliance for a long time.
The supply terminals must not be short-circuited.

Charging

Battery type : 2x AAA

Inserting/replacing batteries

Remove the cover on the back of the controller and insert the batteries. Pay attention to the correct polarity. Oppositely replace the cover.

MOP EXTENSION

G : Watter tank
G1: Mop
G2: Rubber lid

SPARE PARTS LIST

ETA124400100: Dust bin
ETA124400170: Side brushes 2 pcs
ETA124400180: Battery Li-Ion 7,4V, 4000mAh
ETA124400200: Charger station
ETA124400210: Power adapter 12V, 1 A
ETA124400220: Hepa filter + foam filter
ETA124400230: Remote control
ETA124400240: Mop extension
ETA124400250: Mop 2 pcs

PREPARATION FOR USE

Remove all packing material, and remove the vacuum cleaner and accessories.
Remove any adhesive, stickers, or paper from the vacuum cleaner.

VACUUM CLEANER PREPARATION
Install side brushes

CHARGER STATION INSTALLATION

Place the charging station on the floor. Make sure there is enough space on the sides of the base (at least 1 m) and in front of the base (at least 2 m). Don´t expose the charging dock to sunshine.
Connect the adapter to the charging station and then to the wall outlet. (the indicator lights up D1).

VACUUM CLEANER USE

Insert the battery into the remote control, and observe the correct polarity (2 pieces, battery type AAA).

SWITCHING ON THE VACUUM CLEANER

Press button C1 for approx. 3 seconds.
First, you hear a beep of successful switching on the device (light signalization is on).

The vacuum cleaner can be also switched on by placing it in the charging station connected to the mains.
Until the vacuum cleaner is not switched on, it cannot be controlled by remote control

BATTERY CHARGING

Check that the charging station is properly connected to the mains. (light D1 must be on).
Position the device near the charging dock and press the C2 button on the device or F4 on the remote control. If the battery is too low, place directly and correctly the vacuum cleanerdirectly on the charging station.
The vacuum cleaner can be charged even without a charging station. The power adapter can be plugged directly into the vacuum cleaner.

Notes

Standard charging time is 5-6 hours. A fully charged battery will work for approx. 100 minutes, depending on set functions.
The stated operating times are based on ETA‘s internal testing and only apply to a new and fully charged battery. Depending on the age and wear of the battery, the operating time decreases.
After cleaning, the vacuum cleaner will automatically search for the charging

WARNING

If the robot vacuum will not be used for more than 2 days, we recommend full charging of the device and its switching To do this, remove the device from the docking station (charging contacts will be disconnected) and switch off the device by pressing and holding button C1 for more than 3 seconds. Then you can disconnect the charging station from the mains. Do not return the robot vacuum to the docking station!
In this way, you prevent the battery of the device from being deeply discharged and avoid serious problems with putting the robot vacuum into operation in the future and also unnecessary complaints.

START / STANDBY MODE Start (Cleaning)

Press C1/C3 on the control panel or F1/F3/F5/F6 buttons to start the device.

Standby mode (Pause)

Press the C1 button on the control panel or the F7/F1 button on the remote control to interrupt the ongoing cleaning and put the vacuum cleaner in standby mode. If the vacuum cleaner is stopped outside the charging station, it will switch off after five minutes of inactivity.

Note: The robot vacuum should start cleaning from the charging dock. Put the charging dock in a suitable place according to the instructions and do not change its location so that the robot vacuum can easily find it.

CLEANING MODES AND DEVICE FUNCTIONS WITHOUT USING THE ETA SMART APPLICATION

Manual operation
You can operate the device manually using the F2 direction buttons and clean only the areas where cleaning is necessary. Repeatedly press the F2 button to move the vacuum cleaner.

Automatic cleaning

Press the C1 button on the control panel or the F1 button F5 on the remote control. During cleaning, the vacuum cleaner moves gradually and systematically in the space. It divides the space into individual segments. As soon as the vacuum cleaner cleans the entire available space, it automatically searches for the charging station. This is the most used method of cleaning.

Local cleaning

Press and hold C3 on the control panel or F3 on the remote control. When cleaning, the vacuum cleaner moves in the space according to the programmed route. When cleaning has been completed, the device will return to the charging dock automatically. This cleaning mode is suitable for cleaning a small soiled area.

Edge mode
This mode is good for cleaning the edges and corners of a room. In edge- cleaning mode, the robot runs along a border (e.g. wall). Under this mode, the robot will go back to the charging base once the cleaning is finished. Click the button F6 on the remote control to start Edge mode

CAUTION: After pressing the A12 reset button, all parameters set using the ETA SMART application will be lost.

USING THE MOPING ATTACHMENT

Attach the G2 mop to the lower part of the moping attachment correctly. Soak and wring the mop before use.
Open the rubber stopper G1 and fill the mop attachment with water.
Place the mop attachment in place in the vacuum cleaner. There are 4 sticks on the bottom of the attachment and point them into the holes in the vacuum Gently press the attachment until it clicks into the vacuum cleaner. To remove the attachment, grasp it and remove it in the opposite direction using a small force.
Switch on the device and select the required cleaning mode.

Notes

When mopping, we recommend cleaning the individual
Do not use/pour any detergent in the mop water
When mopping, check the vacuum cleaner and add water to the moping attachment, if necessary, or rinse the mop.
Do not use the mop attachment on carpets and prevent the vacuum cleaner from hitting the carpet.
Remove and clean the moping attachment after use. Do not leave it installed on the vacuum cleaner while charging.

OVERVIEW OF LIGHT SIGNALS

Light signal	Meaning
Indicator C4 light Blue	Device connected to WiFi
Indicator C4 Blue pulse light	The device is not connected to WiFi
Slow blue flashing C5	Charging
Indicator C5 light Blue	Charging completed
Slow red flashing D1	The vacuum cleaner is correctly connected to the

charging station.
Indicator D1 light red| The charging station is connected to the power supply network.

APPLICATION ETA SMART
In the simple operation mode, the device can be controlled using buttons on control panel C or remote control F (see above). Vacuum cleaners can be also controlled via an app. Functions are the same as on the remote control. All other information, instructions of the app, instructions, and hints for successful pairing with the home network can be found at: www.etasince1943.com/robot

The app is available from the Apple Store or Google Play database (or use the following QR code for easy installation:

Note: If the QR code is not active, find the app manually (by its name).

VACUUM CLEANER MAINTENANCE

Carry out maintenance and cleaning regularly, depending on the frequency of use and the amount of cleaning. In a more polluted environment (a pet household), more frequent maintenance will be required. Failure to carry out maintenance may damage the vacuum cleaner and its components!

CHARGING CONTACTS CLEANING

Switch off the vacuum cleaner and disconnect the charging station from the power supply! Clean the charging contacts (A3, D3) on the vacuum cleaner and the station with a soft dry cloth. Clean at least once a month. Do not use aggressive cleaning agents or oils to clean the contacts.

DIRT TANK AND FILTERS CLEANING

Remove dirt tank B from the vacuum Dispose of dirt together with normal household waste.
Clean the dirt tank with water
Remove the filters from the dirt Blow or knock the HEPA filter B4 gently. Foam filter B5 can be rinsed in flowing water.

NOTICE

For filter cleaning do not use aggressive detergents or cleaning agents or hot water
Dry cleaning is recommended to maintain the HEPA filter
If you choose to wash the HEPA filter with water, its filtering ability will be
The maximum number of filter washes is Then it is necessary to buy a new one.
It is recommended to change the HEPA filter at least twice a day
The filters are not intended for use in an ability
Cleaning failure and possibly filter replacement can lead to malfunction of the vacuum cleaner

After the maintenance, assemble dirt container filters, insert them back into the device, or store them in a suitable and safe place.

SIDE BRUSHES CLEANING

Remove the two side brushes, clean them, and remove the twisted hair/pet’s hair).
Observe side marks (L – left, P – right).

WHEELS CLEANING

Clean the front, left and right wheels.

NOTICE: Some hair / pet’s hair may be wrapped around the wheel axes and other dirt may stick. Inspect and clean the wheels regularly

SENSORS CLEANING

After each cleaning, clean the sensors with a wet cloth.

MOP EXTENSION CLEANING

Remove mop unit G from the device.
Remove mop G2 from the mop unit. Drain excessive water from the tank. Rinse the tank with water. Rinse mop G2 in flowing water.

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by a professional service! Failure to comply with the instructions of the manufacturer will lead to the expiration of the right to guarantee repair!

PROBLEMS SOLUTIONS

Problem	Designation	Solution
Left fall protection sensor failure	LED flashes 1 time, beep sounds once

Check if the sensor lens A2 on the bottom of the device is dusty and clean it
Front fall protection sensor failure| LED flashes 2 times, beep sounds once| Check if the sensor lens A2 on the bottom of the device is dusty and clean it
Right fall protection sensor failure| LED flashes 3 times, beep sounds once| Check if the sensor lens A2 on the bottom of the device is dusty and clean it
Right Collision Avoidance Sensor Malfunction| LED flashes 4 times, beep sounds once| Check if the right side of the bumper body is jammed
Left Collision Avoidance Sensor Malfunction| LED flashes 5 times, beep sounds once| Check if the left side of the bumper housing is jammed
Left wheel overcurrent| LED flashes 6 times, beep sounds once| Check if the left wheel is stuck
Right wheel overcurrent| LED flashes 7 times, beep sounds once| Check if the right wheel is stuck
---|---|---
Right wheel defective| LED flashes 8 times, beep sounds once| Check if the right wheel is stuck
Left wheel defective| LED flashes 9 times, beep sounds once| Check if the left wheel is stuck
Engine failure| LED flashes 10 times, beep sounds once| Check for foreign objects on the plan
Broken side brushes| LED flashes 11 times, beep sounds once| Check if the left and right brushes are jammed
Appliance gets stuck| LED flashes 13 times, beep sounds once| Check if the device is tangled or stuck

TECHNICAL SPECIFICATION

Robotic vacuum cleaner

Compatibility:

Smart device operational system – Android 6.0 and higher
- IOS 11.0 and higher
Wifi network – 2.4 Ghz
- WPA1 and WPA2 security (recommended WPA2)

NOTICE: The device cannot be operated on IEEE 802.1X-secured WiFi networks (usually corporate WiFi networks).

Charging adapter

The device manufacturer’s name or trademark, business registration number, and address| ETA
AC adapter model identifier| XDJ121T-120100
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 12 V (DC)
Output current| 1 A
Output power| 12,0 W
Average efficiency in active mode| ≥ 82.96 %
Low load efficiency (10%)| ≥ 67 %
Power consumption without load| 0,1 W
Appliance protection class| II.
Charging station

Appliance protection class| III.
Input voltage| 12 V (DC)

Hereby, ETA a.s. declares that the radio equipment type ETA1244 complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the ETA internet address.

The manufacturer reserves the right to change the technical specifications for the respective model. The manufacturer reserves the right to change/update the ETA SMART application without prior notice. Due to the character of such changes/ updates, some information or procedures in this manual might become obsolete or might be missing. The capacity of the product battery decreases over time. Decreasing of battery capacity occurs during normal use of the appliance and is considered the usual wear and tear of the appliance. Decreasing battery capacity is not a defect of the appliance

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components, and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal ofthe product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with a Li- Ion battery with a long life. For environmental protection, it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or the local waste collection site. For environmental protection, it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or the local waste collection site.

Battery removing
Remove the 4 battery compartment cover screws at the bottom of the vacuum cleaner. Remove the battery and unplug the connector. Remove the battery and unplug the connector. For unplugging the connector use more force for the advantage of overcoming the safety fuse against spontaneous disconnection.

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING, OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
KEEP OUT OF REACH OF CHILDREN.
| TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, ARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
|

Please read the instructions manual

| Removable power supply unit
| WARNING

© DATE 22/06/2023
e.č. 42/2023