SOLE MATE SM-76C Intelligent Shoe Cover Machine Instruction Manual
- June 4, 2024
- SOLE MATE
Table of Contents
Operating Instruction Manual
XT-46C
Intelligent Shoe Cover Machine
Our Hospitality Begins at your Feet
Foreword
- Welcome to use XT-46C Intelligent Shoe Cover Machine. With this helper, it is not necessary to worry about the required clean environment being polluted by the sole. This instruction will give you operation details and make you quickly get familiar with it and create the fun of using shoe covers.
Unpacking
Unpack it and check for the following necessary items:
| XT-46C Intelligent Shoe Cover Machine | 1 set |
|---|---|
| Instruction Manual | 1 copy |
| Power Wire | 1 piece |
| Coiled Film | 1 coil |
Product Specifications
| Model | XT-46C |
|---|---|
| Type | Intelligent |
| Dimension | 800x445x330 |
| Level Over Ground | 20mm |
| Net Weight | 21Kg |
| Film-feeding Time | 4.0sec |
| Shaping Time | 2sec |
| Maximum Power | 1300W |
| Start Preheating Time | 3min |
| Voltage/Frequency | 220±5%V 50Hz |
| Hot Standby Power | 75W |
| Highest Temperature of Heater | 250°C |
Operation Condition and Safety
Operation Condition
The shoe cover machine shall be used in a clean environment without much high-
conductivity fiber. The ambient temperature is 5°C-40°C, and the humidity is
not more than 87%. The elevation is less than 1,000m. The film used in the
shoe cover machine is made of PVC with a certain static electricity. If it is
used in a location with the requirement of static electricity, the application
scope must be measured.
Safety
In order to ensure safe usage, please strictly follow the following points:
- Before using the XT-46C machine, please read these instructions carefully and follow the operating procedure. Maloperation is not allowed.
- Before powering on, please make sure the input voltage meets the 220V-240V requirement.
Warnings: the power supply must have a reliably earthed circuit, or it may cause serious personal safety or equipment damage problems.
- In order to avoid machine failure and safety problems, it is prohibited to place the machine in the open or flush the machine with water for cleaning.
- It is prohibited to cover barefoot with film in the machine; It is prohibited to press the footboard when the film is feeding.
- It is prohibited to put any foreign matter into the machine.
- Children are prohibited to use or play the machine alone.
- It is prohibited to walk on the floor where is water and oil, and attention to anti-skid should be paid.
- During maintenance for the machine or moving the machine. it is necessary to disconnect the power.
- Please often clear up the ventilation slot at the bottom of the machine, in order to avoid blocking and influencing the normal operation.
Usage
Turning On
-
Connect to the power: Insert both ends of the wire into the indoors socket and the machine socket respectively.
-
Press to tum on the machine
Installation of Coiled Film -
Open the rear cover of the machine, and dean up the burrs and other impurities on the head of the coiled film, ensuring that the head of the coiled film is smooth.
-
Put the coiled film into the case of the machine horizontally
-
Press the film head with one hand and push it into the film outlet medially.
-
At the same time, press with another hand and send the film into the machine until the film is positioned.
-
Press the footboard by hand and then loose, and the film will be automatically sent out to the working location.
If need to adjust the remaining of the coiled film, please see (a) Reset Remain”.
If it does not work, press to turn back the film and repeat the above steps.
Start to Use
When the coiled film is located in the working position, the machine can be used. -
Step on the position with “PRESS” mark.
-
When five digits on the screen are lit and a long “beep” sound is produced, that means the shoe cover is shaped.
-
Please leave your foot from the footboard, at the same time, the film will automatically stretch out for the next usage.
Turning Off
The machine can be turned off by pressing
How to Use (Diagrammatic Sketch)
Control Panel Instructions
The control panel is composed of the LCD screen and four function keys, as shown on the right figure.
Through the function keys to
implementing three basic functions: “Shoe Covering” , “Warm Wind” and “Data
Adjustment” ,
these functions can be looping shown by pressing key. See the following
figures
- There are two using functions which are “Shoe Covering”, and “Warm Wind” .
- The default function is “Shoe Covering”.
On/Off
Warm Wind
- This function is used to warm or dry, and the heater is in a continuous working state.
- Before using this function, please make sure that there is no film on the footboard. Enter into the “Warm Wind” function, the footboard should be pressed.
- According to the ambient temperature or the requirement, the temperature of the warm wind can be adjusted.
- If you need to quit this function, please press and the machine will be turned off.
- Press and the machine will be turned on and in the ” Shoe Covering” function.
Data Adjustment
As shown in the right figure, press to choose the adjustment function and
Press to enter into the looping submenu of the adjustment function, then press
to select the five sub-functions:
Reset Remain Temp. Control”, “Reset Time”, “Working Time”, “Cancel Timing”
(a) Reset Remain”
According to the number on the coiled film or estimated value of remain, reset remain of the film.
(b) Temp Control
-
This temperature is the temperature of the shoe covering.
-
There are 9 levels of temperature that is from 1 to 9, and the default level is 2. According to personal preference, the level of the temperature can be micro-adjusted.
(C) Reset time
- According to the figure©, adjust the current time.
- Press or firstly, to bring the cursor out.
(d) Working Time
- According to figure(d), reset the open and close time.
- Press or firstly, to bring the cursor out.
(e) Cancel Timing
Troubleshooting
| Failure | Reason | Troubleshooting method |
|---|---|---|
| Blocking | External blocking | Pull out the film from the outlet for next usage |
or withdraw it for another installation.
Internal blocking| Take down the top cover of the machine(with display
screen), and clear up the PVC film which is blocked under the cutting knife.
Non-separated film| Serious blocking| Re-install the film roll; Or take down
the top cover of the machine(with display screen), and clear up the PVC film
which is blocked under the cutting knife.
Non-functional| Contact professional personnel for repair.
Delivered film bias| The film is not normally located| Re-install the film
roll according to the instruction, and pull the film in place until the film
position is correct.
Open the top cover to check the rotation of the coil. If interference is
found, get rid of it.
Delivered direction bias| Natural wind too high| Place the machine in the
leeward location
The air outlet loosened or bias| Contact professional personnel for repair.
Poor shaping effect| Cutting system problem| Contact professional personnel
for repair.
Bottom ntilat ion outlet for blocked| Check the machine bottom and get rid of
it
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>