eta Master Robot Vacuum Cleaner User Manual

Master Robot Vacuum Cleaner
User Manual
Robot vacuum cleaner 3 in 1 with smart application
eta 5229-00/10

USER MANUAL
Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing.

GENERAL SAFETY INSTRUCTIONS

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.

• Check whether the data on the type label correspond with the voltage in electric socket.

•  Never use the appliance if its power cord of adaptor is damaged, if it does not work properly, if it fell down and was damaged.
  In this case take the appliance to a special service to check its safety and proper function.

• The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction  concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance!

• If the power cord of the adaptor is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.

• Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to water. In this case take the appliance to a special service to check its safety and proper function.

• In order to ensure safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.

• If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.

• WARNING: To charge the battery, use only the network adapter supplied with this appliance.

• To power the appliance, only apply safe small voltage in accordance
  with the type plate.

• Don´t put hands close to rotating part.

• Never immerse the vacuum cleaner into water (even its parts)!

• In order to avoid overexposure to UV light, people and house animals must be at a minimum distance of 30 cm from the UV light source. Never stare directly at the UV light source or expose your face or skin to a near UV light  source, UV light can cause burns to eyes and/or skin.

• Never vacuum without a properly inserted filtration system and micro-filters.

• Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items (e.g. ash, hot cigarette butts, gasoline, thinners and aerosol vapours) or greases (e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these  objects may lead to damage of the dust filters, or the vacuum cleaner.

• Pores of the filters may be clogged when vacuum cleaning very fine dust (e.g. fine sand, cement dust, plaster). Thus, air permeability will be reduced and the suction performance will drop. In this case, clean the filters even though the dust container is not full yet.

• Always switch off the vacuum cleaner first and disconnect the power cord from power supply and only then empty the dust container, clean/replace micro-filters, clean the vacuum cleaner or its accessories.

• Never leave the vacuum cleaner exposed to weather conditions (rain, frost, direct sun radiation, etc.).

• Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!

• Disconnect the appliance from the mains when not in use for a long period.

• Secure please gaps on the floor (eg, Threshold Strip) to avoid damaging the rotating brushes. These joints may also limit the vacuum cleaner jams bristle of brush into the gaps.

• This device can not be used on a carpet whose pile length is over 1 cm. At the same time, the vacuum cleaner may not function properly on some types of dark carpets which surface „deceives” the sensors an can cause chaotic  movements of the vacuum cleaner or its failure to reach some parts of the floor. Robot vacuum cleaner can cross floor transition strips of approx. 2 cm in height.

• Make precautions to solve the problem which may make the cleaning in trouble, such as:
  • Keep the easily knock over objects in a safe place.
  • Permian the edge of the carpet.
  • The hanging table cloth and curtain should not touch the ground.
  • The flammable object should be cut from the fire source.
  • Sort out the tangled power cord on the floor.
  • Pick up the newspaper, book, magazine and large piece of paper scattered on the floor.

• Check whether the main brush is correctly fixed inside the robot before cleaning.

• Examine if the dustbin is empty and insure it is fixed before it works.

• See if up-ground height sensor are wiped clean.

• If you only need to clean one room, please close the door.

• If the room which needs to be cleaned wants a partition, you can place the virtual wall, at the same time, check the facing opening width.

• Please be aware that device needs 10 cm of clearance underneath furniture so that it will not become trapped.

• Do NOT drop the Robot, should this happen, run the Robot to see that everything is okay before letting it operate by itself without you being present.

• If the battery is leaking, remove it immediately; it can damage the vacuum cleaner.

• Keep batteries out of reach of children and incapacitated people. A person, who would swallow the batteries, must seek medical help immediately.

• Dispose of a discharged battery in a suitable way.

• Never use the appliance for any other purpose than for the intended one described in these instructions for use! This appliance is not intended for outdoor use.

• The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied with.  failure to replace or maintain all filters regularly and also using non-original filters, the properties of which resulted in failure or damage of the vacuum cleaner is also understood to be improper use of the appliance.

Wireless connection and compatibility

• The ETA company cannot be liable in any way for any incidental, indirect or consequential damages, or for any loss of data or loss due to information leakage during wireless communication.
• Successful wireless communication cannot be guaranteed 100% on all Smart devices and Wifi networks (routers). Due to the variety of devices on the market, there may be cases where the character or specification of a given smart  device or Wifi network (router) makes connection impossible or is in some way disturbed. In addition, several factors, including hardware and software configuration, also affect the success of wireless communication over a Wifi  network. The connection between the robot and your Wifi network can also be adversely affected by the surrounding Wifi networks that they can be tuned to the same channel and disrupt connections (e.g. in housing estates, apartment buildings, etc.). These facts are not a reason to claim the appliance.

The application is owned and operated by a third party (hereinafter the “Subject”) different from HP TRONIC Zain, Ltd. (hereinafter the „Seller“). No personal information is transmitted between the Subject and the Seller. When registering for the application, the customer transfers the personal data directly to the Subject, which becomes the personal data controller. The Application and the associated privacy policy are governed by the Rules of the Subject.

No one else can disassemble maintain or. Transform the product except the maintenance technicians designated by our company or it may cause fire electric shock or personal injury.| Don’t use other charger but the equipped one of the Robot, or it may cause product damage, electric shock or fire due to high voltage.
---|---
Don’t touch high-voltage power cord of the electric appliance with your wet hand, or it may cause electric shock.| Don’t bend the power cord overly or place weight on it, or it may cause power cord damage, fire or electric shock.
Don’t twist your clothes or any part of your body (head, finger, etc.) into the brush or wheel of the Robot, or it may cause personal injury.| Don’t approach cigarette, lighter, match and other heat objects or combustible materials such as the gasoline cleaner.
Don’t use the Cleaner in commercial places, or the Cleaner may be damaged by excessive use.| Insert the power cord of the charger well or it may cause electric shock, short circuit, smoking or fire.
Check whether the adapter and connector are connected well, or it may cause charging failure or even fire.| Remove all easily damaged objects (including luminous objects, fabrics, glass bottles, etc.) before using, or it may cause damage to these objects or affect the using of the cleaner.
Please use the Cleaner cautiously in the presence of the children to avoid frightening or harming them.| Don’t stand or sit on the Cleaner, or it may cause damage to the Cleaner or personal injury.
---|---
Don’t make the Cleaner take in water and other liquors for fear of the product damage.| Don’t use the Cleaner on small tables and chairs or other small space, otherwise the Cleaner may be damaged.
Don’t use the Cleaner outdoors, or it may cause the product damage.| Don’t leave movable thread, wire and other objects with the length of more than 150 mm on the ground or the brush may be entangled.

APPLICABILITY

The product, mainly applicable to home, hotel rooms and small office, is good for cleaning to various short-haired carpet, wood floor, hard floor, ceramic tile, etc.
Since the vacuum cleaner moves freely in the space of your home, it is necessary to adapt the environment to this fact. Before use, remove all unwanted objects (stretched cables, scattered clothes, papers, bags, etc.) from the floor that  could impede the movement of the vacuum cleaner or, conversely, fragile objects (e.g. glass and ceramic vases) that could be damaged by the vacuum cleaner.
If you use the device in an apartment with several stores, it is necessary to carry the charging station along with the device from one story to another.

PRODUCT COMPONENTS

3.1 PACKAGE CONTENTS

Item

| Description| Designation| Quantity
---|---|---|---
| Robotic vacuum cleaner| **A| ** 1

| Charger station| **D| ** 1

| Remote control| F| 1

| Power adapter| **E| ** 1
| Mop extension| **G| ** 1

| Mop| G3| 2
Item| Description| Designation| Quantity
---|---|---|---
| Side brushes| A7| 2×2
| HYBRID BRUSH (combined slat and
bristle brush)| A8| 1
| RUBBER BRUSH| A9| 1
| FINE BRUSH| A10| 1
| Main brush cover| A11a| 1
| Fine brush cover| A11b| 1
| HEPA filter| B4/G5| 1
| Foam filter| B5/G4| 1
| Cleaning tool| I| 1

3.2 ROBOTIC VACUUM CLEANER

A – Robotic vacuum cleaner
A1 – Front bumper
A2 – Sensors against falling downstairs
A3 – Charging contacts
A4 – Storage battery compartment cover
A5 – Drive Wheels (Left / Right)
A6 – Front wheel
A7 – Side brushes
A8 – HYBRID BRUSH (combined slat and bristle brush)
A9 – RUBBER BRUSH
A10 – FINE BRUSH| A11a – Main brush cover
A11b – Fine brush cover
A12 –RESET button
A13 – Service port
A14 – Disinfection UV light
A15 – Laser module
A16 – Wall detection sensor
A17 – Ultrasonic sensor (only ETA5229-10)
B – Dirt hopper
C – Control panel
---|---

3.3 DUSTBIN

B – Dirt hopper
B1 – Dirt tank release button
B2 – Dirt tank
B3 – Filter cover
B4 – HEPA filter
B5 – Foam filter

3.4 CONTROL PANEL

C – Control panel
C1 –ON /OFF/AUTO (automatic cleaning) / STOP (PAUSE) button
C2 – CHARGING / STOP (PAUSE) / LOCAL CLEANING button

3.5 CHARGER STATION

D – Charger station
D1 – Operation indicator
D2 – Signalisation area
D3 – Charging contacts
D4 – Cable storage cover
D5 – Cable storage
D6 – Adapter connection port
D7 – Cable holes
E – Power adapter

3.6 REMOTE CONTROL

F – Remote control
F1 – F1 – ON /OFF/AUTO (automatic cleaning) / STOP (PAUSE) button
F2 – Directional buttons for manual control (FORWARD / RIGHT/ LEFT)
F3 – Button for setting the suction power level
F4 – Voice message on/off button
F5 – Light signalisation on/off button
F6 – Local cleaning button
F7 – Dampening intensity button
F8 – Button for return to charging station
F9 – Switching on/off UV disinfection
F10 – Pressed Button indicator lamp

3.7 MOP EXTENSION

G – Mop extension
G1 – Mop unit locking button
G2 – Rubber stopper
G3 – Filter cover
G4 – Plastic foam filter
G5 – HEPA filter
G6 – Dirt container
G7 – Swing-out handle
G8 – Lid
G9 – Mop

3.8 SPARE PARTS LIST
Hybrid brush: ETA522900060
Rubber brush: ETA522900061
Fine brush: ETA522900062
Side brushes (left + right): ETA522900170
Set HEPA filter and foam filter: ETA522900280
Mop: ETA522900250

PREPARATION FOR USE

Remove all packing material, remove vacuum cleaner and accessories.
Remove any adhesive, stickers, or paper from the vacuum cleaner.

4.1 VACUUM CLEANER PREPARATION
According to use, install the dustbin B or moping attachment G. Install side brushes A7.
Choose appropriate main brush type:

• HYBRID BRUSH – a combination of lamellae and bristles, suitable for carpets and hard floors, including moping
• RUBBER BRUSH – rubber brush for all types of hard floors, suitable for hair collection and mopping
• FINE BRUSH – extra fine brush for hard and delicate floors, suitable for fine dust, pet and human hair (fine brush must be used with fine brush cover A11b)

4.2 CHARGER STATION INSTALLATION

1. Place the charging station on the floor. Make sure there is enough space on the sides of the base (at least 0.5 m) and in front of the base (at least 1.5). Not necessary power cable length can be stored in cable storage D5. Don´t expose  the charging dock to sunshine.
2. Connect the adapter to the charging station and then to the wall outlet. (the indicator lights up D1). Not necessary power cable length can be stored in cable storage D5.

VACCUM CLEANER USE

Remark
The device has voice notification function which can be set in various languages (this function can be deactivated).

Insert the battery into the remote control, observe correct polarity (2 pieces, battery type AAA).
5.1 SWITCHING ON THE VACUUM CLEANER

1. Press button C1 for approx. 3 seconds.
2. First you hear voice message about loading of the system, then the message about successful switching on the device (light signalization is on).

Note
Factory setting of voice messages in Czech
5.2 BATTERY CHARGING

1. Check that the charging station is properly connected to the mains. (light D1 must be on).
2. Position the device near the charging dock and press C2 button on the device or F8 on the remote control. If the battery is too low, place directly and correctly the vacuum cleaner on the charging station.

Remarks
– Standard charging time is approx. 4-6 hours. Fully charged battery will work for approx. 230 minutes, depending on set functions.
– The stated operating times are based on ETA‘s internal testing and only apply to a new and fully charged battery. Depending on the age and wear of the battery, the operating time decreases.
– After cleaning, the vacuum cleaner will automatically search for the charging station.
– The “ETA SMART” application makes it easy to find out the battery status. The application can also be sent back to the charging station at any time.

WARNING
– If the robot vacuum will not be used for more than 2 days, we recommend full charging of the device and its switching off. To do this, remove the device from the docking station (charging contacts will be disconnected) and switch off  the device by pressing and holding button C1 for more than 3 seconds. Confirmation voice message about switching off will be issued. Then you can disconnect the charging station from the mains. Do not return the robot vacuum back to  the docking station! In this way, you prevent the battery of the device from being deeply discharged and avoid serious problems with putting the robot vacuum into operation in future and also unnecessary complaints.
– If the robot vacuum stops outside of the docking station or has been parked in the charging station disconnected from the mains, it will be switched to Sleep mode and after approx. 2 days, the battery will be completely discharged. As a  result, loss of battery´s electrical capacitance can occur (to less than 20%, or even to 0%). This condition is referred to as ‟undercharge“ and results in permanent damage of the battery.

5.3 START / STANDBY MODE
Start (Cleaning)
Press C1/C2 on the control panel or F1/F2/F6 buttons to start the device.
Standby mode (Pause)
Press the C1 button on the control panel or the F1 button on the remote control to interrupt the ongoing cleaning and put the vacuum cleaner in standby mode.
Notes
The robot vacuum must start cleaning from the charging dock. Put the charging dock on a suitable place in accordance with the instructions and do not change its location so that the robot vacuum can easily find it.

5.4 CLEANING MODES AND DEVICE FUNCTIONS WITHOUT USING THE ETA SMART APPLICATION
Manual operation
You can operate the device manually using F2 direction buttons and clean only the areas where cleaning is necessary.
Smart automatic cleaning
Press the C1 button on the control panel or the F1 button on the remote control. During cleaning, the vacuum cleaner moves gradually and systematically in the space according to the programmed route. It divides the space into individual segments. As soon as the vacuum cleaner cleans the entire available space, it automatically searches for the charging station. This is the most used method of cleaning.

Local cleaning
Press and hold C2 on the control panel or F6 on the remote control for approx. 3 seconds. When cleaning, the vacuum cleaner moves in the space according to the programmed route (square 1.8×1.8 m). When cleaning has been  completed, the device will return to the charging dock automatically. When cleaning is complete, the vacuum cleaner stops and goes into standby mode. This cleaning mode is suitable for cleaning a small soiled area.

Suction power level setting
You can switch over various suction power levels by pressing F3. Four levels are on choice.
Switching over dampening intensity levels
Use F7 button to switch over various dampening intensity levels.
Three levels are on choice. This function is only available with the mop unit G (see below).
Switching on/off light signalization
Use F5 button to switch on/off light signalization.
Switching on/off voice messages
Use F4 button to switch on/off voice messages.
Switching on/off UV disinfection
UV disinfection can be switched on/off using button F9.
Return to the charging station
In the Automatic cleaning and Routine cleaning modes, the vacuum cleaner has the function of automatic return to the charging station after the cleaning is completed. You can also send the device to the charging dock by pressing C2 on the control panel or F8 on the remote control.
System reset
Remove dirt container B (or, as the case may be, the mop unit G) and press A12 RESET button using a suitable tool.
CAUTION
After pressing A12 reset button, all parameters set using the ETA SMART application will be lost.

5.5 USING THE MOPING ATTACHMENT

1. Attach the G9 mop to the lower part of the moping attachment correctly. Soak and wring the mop before use.

2. Open the rubber stopper G2 and fill the mop attachment with water. Remove dirt container G6 before filling water.

3. Insert dirt container G6 back into the mop unit.
   Important warning: it is always necessary to place the assembled dirt suction tank G6 in the front part, when using the moping attachment G.
   Failure to do so may result in damage to the product that is not covered by the warranty.
   

4. Place the mop attachment in place in the vacuum cleaner.

5. Switch on the device and select the required cleaning mode.

Notes
– When mopping, we recommend cleaning the individual rooms.
– Do not use/pour any detergent in the mop water tank.
– When mopping, check the vacuum cleaner and add water to the moping attachment, if necessary, or rinse the mop.
– Do not use the mop attachment on carpets and prevent the vacuum cleaner from hitting the carpet.
– Remove and clean the moping attachment after use. Do not leave it installed on the vacuum cleaner while charging.

5.6 OVERVIEW OF LIGHT SIGNALS
Remark
Some light signals can have several meanings. Meanings of light signals are supported by voice notifications or, as the case may be, by relevant notifications in the “ETA SMART” application .

Fast blue/violet flashing, then continuous light

| Start the cleaning
Pause
Continuing the cleaning
Slow blue/violet flashing| Finalization of the cleaning, return to charging dock
Fast blue/violet flashing, then continuous red light| Battery discharged, start of charging
Slow blue/violet flashing| Start of charging

Fast flashing blue/violet, then continuous light

| Charging temporarily stopped
Charging
Charging completed
Continuous red light (approx. 3 seconds), then pulse light| Battery discharged
Fast blue/violet flashing, then faster flashing| Updating device system

Fast red flashing

| Dirt container removed
Dirty filters
Charging dock cannot be found
Device cannot be switched off in the charging dock. Before switching off, remove the device from the charging dock.
Restart
Suction failure
System update failed
Device localization failed
Mop adapter removed
Fast red flashing, then continuous blue/ violet light| Dirt container correctly installed
Fast red flashing, then the lamp goes out| Switched off
Blue/violet flashing, then continuous light| Loss of data, new map creation
Blue/violet light| Charging completed
Slow red flashing| Dirty sensors
Light signal| Meaning
---|---
Red light| Front bumper locked
Device locked
Device not in horizontal position
Main wheel locked
Main brush locked
Side brushes locked
Fast blue/violet flashing| Start of cleaning
Device position message (Find Robot Vacuum function
Fast violet flashing, then continuous light| Connecting the device

APPLICATION ETA SMART

In the simple operation mode, the device can be controlled using buttons on control panel C or remote control F (see above). In order to use all device´s functions, you will have to install and use smart app “ETA SMART”, allowing extension of vacuum cleaner functionality and increased user comfort.
All other information, operating instructions of the app, instructions and hints for successful pairing with home network can be found at: www.etasince1943.com/robot
The app is available from Apple Store or Google Play database (or use the following QR code for easy installation:

https://qrs.ly/ucdsv11

Remarks
If QR code is not active, find the app manually (by its name).

VACUUM CLEANER MAINTENANCE

Carry out maintenance and cleaning regularly, depending on the frequency of use and the amount of cleaning. In a more polluted environment (a pet household), more frequent maintenance will be required. Failure to carry out maintenance may damage the vacuum cleaner and its components!

7.1 CHARGING CONTACTS CLEANING
Switch off the vacuum cleaner and disconnect the charging station from the power supply! Clean the charging contacts (A3, D3) on the vacuum cleaner and on the station with a soft dry cloth. Clean at least once a month. Do not use aggressive cleaning agents or oils to clean the contacts.

7.2 DIRT TANK AND FILTERS CLEANING

1. Remove the dirt tank B from the vacuum cleaner. Dispose of dirt together with normal household waste.

2. Clean the dirt tank with the tool I (or other suitable).

3. Remove the filters from the dirt tank and clean them with tool I (or other suitable). Blow or knock the HEPA filter B4 gently.
   Plastic foam filter B5 can be rinsed in flowing water. NOTICE
   – For filters cleaning do not use aggressive detergents or cleaning agents or hot water
   – Dry cleaning is recommended to maintain HEPA filter parameters.
   – If you choose to wash the HEPA filter with water, its filtering ability will be reduced.
   – The maximum number of filter washes is 3x. Then it is necessary to buy a new one.
   – It is recommended to change the HEPA filter at least twice a year.
   – The filters are not intended for use in a dishwasher.
   – Cleaning failure and possibly filters replacing can lead to malfunction of the vacuum cleaner!

4. After the maintenance, assembly dirt container incl. filters, insert it back to the device or store in a suitable and safe place.

7.3 MAIN BRUSH CLEANING

1. Press the cover towards you and remove the cover A11 and remove the main brush A8/A9/A10 from the vacuum cleaner.
2. Clean the main brush with the cleaning tool I (or other suitable). You can also use scissors to remove tangled hair / hair. Wipe the main brush cover and main brush compartment with a soft, dry cloth.

7.4 SIDE BRUSHES CLEANING

1. Remove the two side brushes, clean them and remove the twisted hair / pet’s hair).
2. Observe side marks (L – left, P – right).

7.5 WHEELS CLEANING
Clean the front, left and right wheels with the I device.

NOTICE
Some hair / pet’s hair may be wrapped around the wheel axes and other dirt may stick. Inspect and clean the wheels regularly.

7.6 SENSORS CLEANING
After each cleaning, clean the sensors with tool I (or another suitable one).

7.7 MOP EXTENSION CLEANING

1. Remove mop unit G from the device.
2. Remove dirt container G6 from the mop unit.
3. Remove mop G9 from the mop unit. Drain excessive water from the tank. Rinse the tank with water. Rinse mop G9 in flowing water. More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by a professional service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

PROBLEMS SOLUTIONS

The device cannot be switched on

| Low battery. Place the device in the charging dock and recharge.
Ambient temperature lower than 0 °C or higher than 40 °C. Working temperature of the device is 0-40 °C.
Problem| Solution
---|---

The device cannot be charged

| Remove the device from the charging dock and check correct connection of the cleaning dock to the electric mains.
Check and clean charging contacts (on the device and the charging dock).
The device cannot find its charging dock| The device is too far from the charging dock, move it nearer to the charging dock. Do not relocate the charging dock during cleaning operation of the device.
Abnormal behavior of the machine| Restart the device.
Abnormal sounds are generated| Wheels and the brushes are clogged. Clean where necessary.
Lower cleaning potential or remaining dust on the surface| The dirt container is full. Clean it.
The filters are clogged, clean or replace the filters.
The main brush is clogged. Clean it.

TECHNICAL SPECIFICATION

Declared acoustic level is 68 dB(A) re 1pW.

Compatibility:
Smart device operational system – Android 6.0 and higher
– IOS 11.0 and higher
WiFi network
– 2.4 / 5 SGHz
– WPA1 and WPA2 security (recommended WPA2)

NOTICE

The device cannot be operated on IEEE 802.1X-secured Wifi networks (usually corporate Wifi networks).

Charging adapter

Device manufacturer’s name or trademark, business registration number and address| ETA
AC adapter model identifier| NLD100240W1U4
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 24 V (DC)
Output current| 1.0 A
Output power| 24.0 W
Average efficiency in active mode| 86.70 %
Low load efficiency (10%)| 79.08 %
Power consumption without load| 0.07 W
Appliance protection class| II.
Charging station

Appliance protection class| III.
Input voltage| 24 V (DC)

Hereby, ETA a.c. declares that the radio equipment type ETA5229 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the ETA internet address.
The manufacturer reserves the right to change the technical specifications for the respective model. The manufacturer reserves the right to change/update the ETA SMART application without prior notice. Due to the character of such changes/updates, some information or procedures in this manual might become obsolete or might be missing.
The capacity of the product battery decreases over time. Decreasing of battery capacity occurs during normal use of the appliance and is considered usual wear and tear of the appliance. Decreasing battery capacity is not a defect of the appliance.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with the Li-Ion battery with long life.
For environmental protection it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site. For environmental protection it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site.
Battery removing
Remove the 2 battery compartment cover screws at the bottom of the vacuum cleaner.
Remove the battery and unplug the connector. Remove the battery and unplug the connector. For unplugging the connector use more force for advantage of overcoming the safety fuse against spontaneous disconnection.
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS. TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS,  BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

REMOVE FILM BEFORE USE
LEDS EMIT VERY STRONG UV RADIATION.
DON’T LOOK DIRECTLY INTO THE LED LIGHT,UV RADIATION CAN HARM YOUR EYES.
TO PREVENT EVEN LNADEQUATE EXPOSURE,WEAR PROTECTIVE EYEWEAR.
IF LEDS ARE EMBEDDED IN DEVICES, PLEASE INDICATE WARNING LABELS
AGAINST THE UV LIGHT LED USED.
KEEP OUT OF REACH OF CHILDREN.

– Please read the instructions manual
– Removable power supply unit

NOTICE

https://qrs.ly/ucdsv11 ****

References

• eta.de
• Technická podpora robotických vysavačů | ETA - tady je doma
• ETA Magyarország – ETA HUNGARY
• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• eta-polska.pl
• Obsługa robotów odkurzających | eta-polska.pl
• ETA - tady je doma
• Technická podpora robotických vysavačů | ETA - tady je doma
• Robotporszívók műszaki támogatása – ETA HUNGARY
• ETA - tu je doma
• Robot vacuum cleaner support – ETA since 1943

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>