NEXIGO AS200 Sliding Tray Ultra Short Throw Projectors User Manual

: June 16, 2024
: NEXIGO

Table of Contents

NEXIGO AS200 Sliding Tray Ultra Short Throw Projectors
Product Information
Installation Guide
Setting up the Sliding Tray for Use with the Projector
IMPORTANT SAFETY NOTES
INTRODUCTION
WHAT’S IN THE BOX?
BUTTON INSTRUCTIONS
SPECIFICATIONS
INSTALLATION GUIDE
FCC REQUIREMENT
WEEE
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NEXIGO AS200 Sliding Tray Ultra Short Throw Projectors

NEXIGO-AS200-Sliding-Tray-Ultra-Short-Throw-Projectors-
PRODUCT

Product Information

Specifications

Maximum Load Capacity: 55.12 lbs
Maximum Forward Slide Distance: 12.99 inches
Device Dimensions: 24.02 x 14.49 x 2.36 inches
Product Weight: 25.66 lbs

Installation Guide

Mounting the Sliding Tray

To mount the Sliding Tray on a table or credenza:

Place the Sliding Tray in the desired position on the table or credenza.
Insert the long sides of the two Bracket Plates into the bottom of the Sliding Tray, with the short sides facing downward.
Turn over the Sliding Tray and place the long end of each bracket plate on the bottom of the tray, with the short end pointing outward.

Setting up the Sliding Tray for Use with the Projector

To set up the Sliding Tray for use with your projector:

Power the Sliding Tray using the provided Power Cable.
Set your projector on the tray and power it on.
Adjust the distance of the Sliding Tray using the forward and backward buttons on the back of the tray. When the projected screen is in the desired position, wait for 30 seconds to save that position as a preset.
Power off both the tray and the projector. Wait for an additional 30 seconds before proceeding to the next step.
Connect the Sliding Tray to your projector using the provided USB Cable.
Power on the tray to return it to its initial position. If it doesn’t return to its initial position, please start over the preset process or contact customer support for assistance.
Turn on your projector to return the Sliding Tray to the preset position. The tray will automatically move into the preset position when you power your projector on and return to its initial position when you power your projector off.
For reference, remove the adhesive backing from the four L-Brackets and place them at each corner of your projector. These brackets will serve as a reference point if you ever need to move the projector back into place.

IMPORTANT SAFETY NOTES

HAZARD: Small Parts. Keep out of reach from children under 5 years of age.
Make sure that the NexiGo Sliding Tray is powered off during installation.
Avoid placing your hands into any gaps in the tray to prevent injury.
Keep the area in front of the tray clear and free from obstructions.
Do not attempt to force the tray.
Do not attempt to disassemble or repair the product yourself. If you encounter any technical issues, seek professional assistance.
Due to the significant weight of the product, it is advised to handle it with care to prevent any potential incidents.
Please take precautions to avoid any risk of ﬁnger pinching when using the product.
Avoid exposing the tray to moisture or liquids to reduce the risk of ﬁre and/or electric shock.
Only use attachments and accessories directly speciﬁed by the manufacturer.
Only use a power source with the voltage speciﬁed in this manual to avoid potential hazards.
Avoid setting up the tray in areas prone to vibration or other disturbances to ensure stable operation.

INTRODUCTION

The NexiGo Sliding Tray is an automated platform designed for use with ultra- short throw projectors. The tray can be repositioned forward/backward with the buttons on the back of the device. Its integrated memory enables it to automatically return to a pre-set position every time the projector powers on.

WHAT’S IN THE BOX?

NEXIGO-AS200-Sliding-Tray-Ultra-Short-Throw-Projectors-
FIG-1

BUTTON INSTRUCTIONS

Forward: Move tray forward.
Backward: Move tray backward.
Power: Connect tray to a power source.
Signal: Connect tray to your projector.

NEXIGO-AS200-Sliding-Tray-Ultra-Short-Throw-Projectors-
FIG-2

SPECIFICATIONS

NEXIGO-AS200-Sliding-Tray-Ultra-Short-Throw-Projectors-
FIG-3

INSTALLATION GUIDE

HOW TO MOUNT THE SLIDING TRAY?

Mounting to a Table or Credenza

Place the SlidingTray in the appropriate position on the table or credenza, and insert the long sides of the two Bracket Plates into the bottom of the Sliding Tray (with the short sides of the Bracket Plates facing downward), marking the lengths at which the bracket plates need to be inserted.
Turn over the Sliding Tray. With the holes in the bottom of the tray. Place the long end of each bracket plate on the bottom of the tray, with the short end of the bracket plate pointing outward, as shown below.
To fasten the Bracket Plates to the tray, insert an M5×16mm Screw into each of the six holes and tighten until snug.
M5×16mm Screw can be inserted into any place of each hole of the bracket plate.
Place the Sliding Tray on the surface where you intend to keep it. Fix the bracket to the back of your table or credenza using the M4×15mm Self-Tapping Screws.

HOW TO SET UP THE SLIDING TRAY FOR USE WITH THE PROJECTOR?

Setting a Position Preset

Power the Sliding Tray with the provided Power Cable.
Set your projector on the tray and power on it.
Adjust the distance of the Sliding Tray using the forward and backward buttons on the back of the tray. When the projected screen is in the right position, wait 30 seconds to save that position as a preset.
Power off both the tray and the projector. Please wait 30 more seconds before proceeding to the next step.

Connecting the Projector to the Sliding Tray

Connect the Sliding Tray to your projector using the provided USB Cable.
Power on the tray to return it to its initial position. If it doesn’t return to its initial position, please start over the preset process or contact customer support for more assistance.
Turn on your projector to return the Sliding Tray to the preset position. The tray will now automatically move into the preset position when you power your projector on and return into its initial position when you power your projector off.
Remove the adhesive backing from the four L-Brackets and place them at each corner of your projector. These brackets will serve as a reference point if you ever need to move the projector back into place.
Use the Reusable Cable Ties to bundle all cables together.
Please carefully repeat all of the steps above when moving the tray to different locations.

FCC REQUIREMENT

Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference,
this device must accept any interference received, including interference that may cause undesired operation.

WEEE

CORRECT DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL & ELECTRONIC EQUIPMENT)

(Applicable in countries with separate collection systems)
This marking on the product, accessories, or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

CONTACT INFORMATION

Website: www.nexigo.com
Manufacturer: Nexight INC
Address: 11075 SW 11th St, Beaverton, OR 97005, US
Tel: +1(458) 215-6088 Email: cs@nexigo.com